Bojano LMGC Series LED Illuminated Aluminum Cabinets Installation Guide

Bojano LMGC Series LED Illuminated Aluminum Cabinets Installation

LED ILLUMINATED ALUMINIUM CABINETS

WARNING:
All fittings must be installed by a trained professional. Switch off the electrical supply onthe main unit Before installation and maintenance. Suitable for Bathroom Zones 2, 3 and non bathroom/dry areas. See diagram below. Not suitable for the above Bath Zones (Zone “O”& Zone”1”)nor for installation in Saunas, Steam Rooms or Shower Cubicles. DO NOT connect to a plug and socket outlet. Rated IP44 and suitable for indoor use only. Do not fix to damp or conductive surfaces Site well away from curtains and fabrics. Never cover the mirror. Switch off after use Do not leave on for prolonged periods.

IMPORTANT! BEFORE YOU BEGIN

Inspect the product immediately upon receipt for transit damage, missing parts or manufacturing faults. Handle the product with care and protect against knocks to all sides and edges of the glass. Fixings supplied are for use in solid walls, hollow or stud walls will require specialist fixings available from your hardware supplier Make sure that you have all the tools you need to complete the job (SEE BELOW) Ensure there are no hidden pipes or cables in the wall before drilling. If driling holes in ceramic tiles use a piece of masking tape on the tile to stop the drill bit from slipping.

AFTERCARE INSTRUCTIONS

Clean using a soft dry cloth only when turned off. Never use cleaning agents or abrasive materials. Do not allow moisture to come into contact with the lamps.

TOOLS REQUIRED

CONTAINS:
760024-LED-MC 760036-LED-MC 1x Mirror cabinet, 4 x screws and 4 x wall plugs 760048-LED-MC 1x Mirror cabinet, 5 x screws and 5 x wall plugs

INSTALLATION INSTRUCTIONS

1. Switch off the electrical supply at the mains before beginning
2. Using the template, mark the wall with a pencil.
3. Ensure that the mirror cabinet is level and check there are no hidden pipesor cables before driling.
4. Wearing suitable eye protection, drill 4 holes using a 6mm dill bit and fix the wall plugs and screws in place leaving the end of the screw head protruding from the wal.
5. Make the electrical connections in accordance with current IEE wiring regulations. If in doubt consult your electrician.
6. Carefuly hang the mirror.
7. Switch on the mirror lights.

Exploded view

Recessed Opening Dimensions (in.)

ELECTRICAL SAFETY INSTRUCTIONS
All connections must be installed by a licensed electrician, in accordance with current building codes. Consut a qualified electrician.
IMPORTANT
Always switch off the electrical supply at the main during installation and maintenance. It is recommended that the circuif breaker is switched ot for the necessary circuit before installation commences. Fitting in Bathrooms is subject to the appropriate building code Regulations. This product is NOT suitable for outside zones. It is also NOTsuitable tor installation in saunas, steam rooms or shower cubicles. This product is only suitable for permanent installation. DO NOT connect to a trailing plug and socket oulet. This product is only suitable tor indoor use. DO NOT attach the product to surfaces that are damp or otherwise electrically conductive.

INSTALLATION CARE & SAFETY

Wear suitable eye protection when drilling. Take care wnen using power tools. Beware ot hidden cables or pipes. Take care if drilling on tiled surfaces in case the drill slips. A piece of masking tape applied to the wall betore marking out the fixing holes will stop the drill from wandering.

CLEANING

is recommended that the unit is cleaned with a sot, dry, non abrasive cloth when turned ott. Never use deaning agents or abrasive materials on any type of surtace fnish. DO NOTallow moisture to come into contact with the electrical components.

INSTALLATION INSTRUCTION

IMPORTANT

DO NOT strike glass components with hard or pointed items. DO NOT place very hot or very cold items against or in close proximity to glass surfaces unless an adequately thick insulation materal is Used to prevent such items coming in contact with the glass. The nominal thickness of the mirror glass used in this product is 1/4* and is film backed for safety. If the glass becomes chipped or broken replace immediately.

The first step Is to make the electrical connection from the mirror to the mains suPPIy. Ose the connection wire toung at thereare sne mrror ake tns. ake necessary connections. A second person will need to nold the mirror in place wniist electrical connectIons are made. Electric Outlet: This outlet only suitable for those appliances with low power such as shaver or electric toothbrush, the maximum watts of this outlet is 500W.

Assembly instruction for wall mount installation

1. Measure the length,width, depth of back of cabinet for wall mount
2. Fix the screws of the supporting bracket at the desired location. (See diagram D)
3. With the cabinet mounted at the supported bracket, mark the location of the top slideable brackets and fix the screws (see diagram E). Hint: The electrical supply must be connected before fixing the top brackets.
4. Before making any electrical connections it is necessary to turn off the main electricity supply. This unit is provided with a supply cable already fitted. This cable should be fted to the household lighting circuit or to a fused 3 AMP supply.
5. Fitting the glass shelves. Firstly insert a shelf into the top two shelf support brack ets then slide upwards so the grub screws on the under side of the support brackets (Screw C) can be sufficienly tightened to hold glass in place. Repeat for the bottom shelf (NOTE: be careful not to overtighten). Shelves can be positioned accordingly by sliding the supports up or down (NOTE: Take care to use both hands when sliding shelves and ensure thatsupport brackets at both ends slide simutaneously). C
6. IF the doors are out of alignment first remove the soft close buffer (from the relevant hinges) which clips into the main hinge plate. The soft-close hinges offer adjustment in 3 directions via adjustment screws Dand E (see diagram
7. Measure the length,width, depth of back of cabinet for recess (see diagram A)
8. Put cabinet into recessed hole and fitting screws through installation holes at left and right side aluminum frame ( see diagram B)
9. Before making any electrical comections it is necessary to turn off the main electricity supply. This unit is provided with a supply cable already fitted, This cable should be fted to the household lighting circuit or to a fused 3 AMP supply. Connections should be made in accordance with the latest regulations. This cabinet is manufactured to CLASS 1 and requires an earth connection.
   Operation Instructions:
   1.Quick touch the light switch for LED color change (3 options available: warm, neutral, and cool).
   2.Press and hold the light switch to activate dimmer function.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>