DOC W3665A Spider Electrical Self-Balancing Vehicles Instruction Manual

DOC W3665A Spider Electrical Self-Balancing Vehicles

The document overview

Description

Describe safety and warning infom1ation to ensure every user can drive Electrical Self-balancing Vehicles safely and enjoy Electrical Self-balancing Vehicles .
A.Introduce every part of Electrical Self-balancing Vehicles manual warnings and precautions to help you enjoy it.
B. This manual is only for Electrical Self-balancing Vehicles.
C.Any questions, please contact Electrical Self-balancing Vehicles

Driving Risk

Electrical Self-balancing Vehicles is a personal transporter and Personal entertaimn ent, our technology and production processes have strict testing for every Electrical Self-balancing Vehicles. Driving without attention to contents of this manual may cause injury.
Falling, losing control, collision, or failure to obey Electrical Self- balancing Vehicles manual, may cause injury even death. In order to minimize the risk of driving, insure that you read Electrical Self-balancing Vehicles manual.

1. The risks of driving under low temperature. Low temperature will affect the lubrication of moving parts inside then create internal resistance; at the same time, under the condition of low temperature, discharge capacity and the capacity itself of the battery will significantly decreased, so ,don’t do violent action when riding a Electrical Self-balancing Vehicles especially under low temperature (below -10 °C ), otherwise it may increase the risk of losing control and falling down.

Preparation before Driving

Before driving, please check level of battery, details in chapter Failure to obey the Electrical Self-balancing Vehicles Manual, 1nay cause injury.

Related Instructions

Instruction below are for Electrical Self-balancing Vehicles. Please give special attention to related WARNING! and NOTE.

notes on usage.

Product lntroduction

Description of Electrical Self-balancing Vehicles

Electrical Self-balancing Vehicles is a high-tech electric product, it is based on dynamic balance principles and can control forward, backward, and stopping. Easy Operation, flexible control, low carbon footprint, green environmental protection and easy on-road travel are Electrical Self-balancing Vehicles ‘s advantages. Electrical Self-balancing Vehicles is widely used in leisure, scenic tours, security patrol and other fields.

Working Principles

Electrical Self-balancing Vehicles uses gyroscopes and acceleration sensors to control balance intelligently depending on center of gravity. Electrical Self- balancing Vehicles also uses a servo-control system to drive the motor. It adapts to the human body, when you stand on the Electrical Self-balancing Vehicles, lean body forward or backward and the power plant will control the wheels in a forward or backward movement to keep balance. When you tum, you need to slow down and move body left or right. Built-in inertia dynamic stabilization system can keep the direction of frontward and backward, however, it cannot guarantee the stability of left and right. When you drive Electrical Self-balancing Vehicles, please shift your weight in order to overcome the centrifugal force and improve the security of turning.

Control Device and Information Display Device

Mat Sensor

A. While driving Electrical Self-balancing Vehicles, you must ensure that you are stepping on the foot mats, please don’t step on any other area besid h
B. Please do not put items on the mats which will make Electri. cal Self- balancm. g Vie h 1′ c1 e s sw1. tc h on, an d m. crease t h e probab·11 ·1 ty of collision and ca estemats · people or damage to Electrical Self balancing Vehicles. use Jury to

Display Board

Display boar? is locate? on the middle of Electrical Self-~alancing Vehices. It is_ for displaying the current infrmoatio~ o~ Electrical Self-balancing Vehicles
A. Battery Display: This green LED hight md1cates the Electrical Self- balancmg Vehicles 1s fully charged, red LED hight md1cates the power is down to 20°’ h • • 101 wen LED light become red, please recharge 1t.
B. Rurming LED: When the operator triggers the foot switches, the running LED will light up, which means that the system has entered the running state; when the system has an error in operation, rurming LED light will tum to red. please recharge to.

How to connect Bluetooth

1. Press the switch turn on the scooter.
2. You would hear a sound that means the built-in Bluetooth function well.
3. Then turn on the Bluetooth of your mobile, search for the Bluetooth of the scooter.
4. There will be a sound again indicates the Bluetooth of the mobile and the scooter are connected.
5. Put on some music and test if the Bluetooth speaker works.

Sell-balancing circuit board function

1. Circuit board installation requirement: aluminium casting near battery, major circuit board connect switch board.
2. Low-air warning: when the source voltage was 34V + 0.SV,the buzzer alarm will ring, red light turn on(green light indicator flashes and close, then red light will turn on).
3. Overs peed warning: On the player mode, speed more than 1 0krn/h, the buzzer alarm will ring. On the easy mode, speed more than 8km/h, the buzzer alarm will ring.(hub motors:6.5 inches).
4. Charge indication: While charging, press the switch tum on the scooter, circuit board break-off ,indicator flashes(yellow light).
5. Goto Start: if the GotoStart abnormal, Electrical Self-balancing Vehicles will auto shut off in 1s.
6. Change mode: The first mode is fit to player , then you can boot button is pressed in twice to enter the beginner mode (8km/h).
7. Safe protect: the max angle is 80 ° ,when the angle more than 80 ° ,vertical motor and Photo inductive switching motor both stopped work.
8. Motor operation: Electrical Self-balancing Vehicles Positive Speed is the same as negative speed, according to the circuit board ,the angle bigger and speed faster. On the other hand, block the light sensing system of the circuit board , the blue light will tum on.

Safe-using of Electrical Self-balancing Vehicles

We hope every user can drive Electrical Self-balancing Vehicles safely and enjoy the fun. You can recall the memories of learning how to ride a bicycle, drive a car, ski or use other similar means of transportation; all these experiences can be applied to our product.

1. Please follow the related content in “Product Manual”. We strongly recommend that you read the “Product Manual” carefully before riding Electrical Self balancing Vehicles the first time. Check whether tires are damaged, or parts are loose before driving. If there is any abnormal situation, please contact local dealer for repair.
2. Please carefully read the “Product Manual”, this will help you to get a lot of important safety information such as speed limits, vibration alert and safety shutdown, etc.
3. Do not use the Electrical Self-balancing Vehicles incorrectly to endanger the safety of persons or property.
4. Do not modify the parts of Electrical Self-balancing Vehicles, it will affect the performance of Electrical Self-balancing Vehicles, and can cause serious injury.
5. WARNING -Risk of Fire -No User Serviceable Parts.

User’s Weight Limit

1. The following two points are the reason for a weight limit:
   ——::ro ensure the safety of the user.
   ——::ro reduce damage due to overload.

2. Maximum Load: 75kg

3. Minimum Load: 20kg

WARNING! :Overweight use may increase possibility of iuj1lry.

Environmental Limit

There are a lot of factors that will affect driving range such as ; The ground: A smooth, flat surface will increase the driving distance, while an incline or hilly terrain will reduce the distance.

1. Weight: The weight of the driver can affect driving distance.
2. Ambient temperature: Please ride and store Electrical Self-balancing Vehicles under recommended temperature, which will increase driving distance.
3. Maintenance: Reasonable battery charging and maintenance will increase thedriving distance.
4. Speed and Driving Style: Maintaining a moderate speed will increase distance, on the contrary, frequent starting, stopping, acceleration and reduce the distance. deceleration Will

Speed Limit

1. Electrical Self- Balancing vehicle scooter’s top speed is 10km/h
2. When the speed is close to the maximum allowable speed, the buzzer alarm will ring.

Learning to drive

It is important to learn and remember the related warnings and notes before driving Electrical Self-balancing Vehicles.

Operation Procedure

Step 1: Start Electrical Self-balancing Vehicles press the power button.
Step 2: Prepare driving

1. Put Electrical Self-balancing Vehicles on a flat surface.
2. Put one foot on pad that will trigger pedal switch.
3. The balance indicator light will turn on ,enabling the automatic balancing system.
4. Put the other foot on the other pad.

Step 3: Control Electrical Self-balancing Vehicles After standing up successfully, keep your balance and center of gravity stable while Electrical Self-balancing Vehicles is in stationary state Make backward movements through body, remember do not make sudden movements.
NOTE: If user stands on Electrical Self-balancing Vehicles, and platform is not at the level state, the buzzer will alarm and warning indicator will light up. at that time the system cannot enter self-balancing status, users are forbidden to operate Electrical Self-balancing Vehicles.
Step 4: Control Turning Lean your body slightly left, Electrical Self- balancing Vehicles will turn to the left; lean right, and it will turn to the right. The right foot forward will turn left, The left foot forward will turn right.
Step 5: Get off
Keep Electrical Self-balancing Vehicles balanced; get one foot down, then the other foot off mat quickly.

WARNING :

1. Do not tum sharply or at high speed to avoid danger.
2. Do not drive and tum around quickly on slopes, it may cause serious injury.

Protection Function

During operation, if there is a system error or illegal operation, Electrical Self-balancing Vehicles will prompt drivers in different ways. Prohibited riding , alarm indicator lights up, buzzer sounds intermittently.

1. lfyou get on the Electrical Self-balancing Vehicles, while the platform is forward or backward more thanlO degrees
2. Battery voltage is too low.
3. In charging mode.
4. In driving status, platform begins to tilt, stop driving.
5. Over-speed.
6. Battery has a short.
7. Motor temperature is too high.
8. Electrical Self-balancing Vehicles body rocking back and forth over 30 seconds.
9. System enters protection mode, alarm indicator will be lighted up, buzzer will alarm.
10. The platform is leaned forward or backward more than 15 degrees, Electrical Self-balancing Vehicles will engine off. o
11. Tires blocked, Electrical Self-balancing Vehicles will halt after 2 seconds.
12. Battery is insufficient below protection, Electrical Self-balancing Vehicles will engine off after 15 seconds.
13. Sustained high discharge rate during performance (such as driving up long steep slope), Electrical Self-balancing Vehicles will engine off after 15 seconds.
14. When Electrical Self-balancing Vehicles goes into engine off, system will halt, press battery display to unlock.
15. Do not continue driving Electrical Self-balancing Vehicles when the battery is exhausted or the system initiates the stop state, it may lead to danger.
16. Continued driving under low power will affect battery life.

• You should always keep in 1nind your height has increase 6.5 inches, be carefully when you pass doors.
• When turning, please keep yow· balance.
• Do not be distracted when driving Electrical Self.-balancing vhicles, such as talking on the phone, listening to music, or engaging in any other activities.
• Do not drive on slippery roads or on rainy days, reverse turning wh1le at high-speeds or long range high-speeds.
• Do not drive in dark places.
• Avoid driving in impediment and smooth surface, such as: snow, ice, and slippery floor.
• Do not drive in road with obstacles, such as tvvigs, litter or small stones, etc.
• Avoid driving in narrow spaces.
• Avoid driving on a steep slope.
• Avoid driving in unsafe places, including flammable gas, steam, liquid, dust, fiber which could cause fire or an explosion accident.
• Can choose to add bluetooth APP, acoustics or LED.
• When the voltage of Electrical Self-balancing Vehicles was too lows the buzzer alarm will ring,Player must get off as soon as possible.

Usage of Battery

This section mainly describes the charging method of Electrical Self-balancing Vehicles , how to maintain the battery, some security issues, and battery specifications.
For users’ safety, and the maximum extent of prolonging the battery life and improved battery performance, please follow the following operations using the battery.

Battery Power

You must stop driving if Electrical Self-balancing Vehicles displays low power, or it may affect lifetime use and cause dangerous situations. Don’t use the battery if the following occurs:

1. Use only supplied battery pack
2. Emits odor or overheats.
3. Don’t touch any leaking materials.Avoid damp the battery
4. Children and animals are forbidden to touch battery.
5. The charger must be taken out before installing or driving or it may cause danger.
6. Battery contains dangerous substances, do not disassemble the battery, do not insert anything into the battery.
7. Please use the charger provided from Electrical Self-balancing Vehicles .Please read the Product Manual carefully, and follow the rule.
8. Don’t charge the battery that has been overly discharged. It should be discarded for safety.
9. Electrical Self-balancing Vehicles battery should be disposed of according to local law.
10. Please put the used battery in a right place,easpilly no water or fire.
11. The charging time not over 12 hours .
12. Keep the using envirorunent,temperature:-10-40°C , relative humidity:55 + 20%.
13. In spare time,the battery keep Full electricity.on the other hand, avoid the battery touch the metal.

Charging process

1. Ensure charging port is dry.
2. Plug the charging cable into the Electrical Self-balancing Vehicles, make sure indicator lights up, then connect the cable with the power supply (ACIOOV-240V; 50-60HZ).
3. The red light indicates that it has began to charge, otherwise check whether the cable is connected.
4. When the indicator light goes from red to green, it indicates that battery is fully charged. At this time, please stop charging, over-charging will affect lifetime use.
5. Use local standard plug.
6. Charge and store battery as suggested, otherwise it will damage the battery. The charging time is about 2 hours.
7. Keep the charging environment clean and dry.
8. Do not insert anything into the charging port.

Temperature

The best charging temperature is 25 °C. Over cold and over heat will not completely charge the battery.

Battery Parameter

Battery Parameter

Model| KD362-65
Battery type| Lithium-ion
Charging time| 5 hours
Voltage| 36V
Batterv Capacity| 2Ah
Working Temperature| – I0′ C – 40 ‘C
Charging Temperature| 0’C-40’C
Storage Temperature| Within 3 moths:0 ‘C – 35’ C
Within I year:25 ‘C

Shipping Notes

WARNING! :Lithium battery contains dangerous articles. Ship lithium only according to local law.
NOTE:Please contact us or our authorized agent for parts and Electrical Self- balancing Vehicles can send to you according to your requirements.

Shipping and Maintenance

Electrical Self-balancing Vehicles requires the user to do routine maintenance. This chapter describes maintenance steps and important operating tips. Before you perform the following operations, ensure the power and charging cable are disconnected. If the battery is charging, the operation is not allowed.

Clean Electrical Self-balancing Vehicles

1. Disconnect the charger and tum off Electrical Self-balancing Vehicles.
2. Wipe the cover.
   WARNING! :Avoid using water or other liquids on the Electrical Self- balancing Vehicles for cleaning .. If water or other liquids seep into Electrical Self balancing Vehicles, it will cause permanent damage to the internal electronics.

Store Electrical Self-balancing Vehicles

1. Fully charge your battery before storing.
2. If you store Electrical Self-balancing Vehicles more than one month, please remove the battery and charge it at least every three months
3. If the storage ambient temperature is below 0 ·c ( indoor) , please do not charge. You can bring the Electrical Self balancing Vehicles into a warm environment (IO °C ~ 25 °C) for charging.
4. To prevent dust from entering the Electrical Self-balancing Vehicles, you should cover Electrical Self-balancing Vehicles.
5. Store Electrical Self-balancing Vehicles indoors in a dry and suitable temperature. If you do not use it for a long time, please do not connect the power.
6. Prolonged Exposure to UV Rays, Rain and the Elements May Damage the Enclosure l\1aterials, Store Indoors When Not in Use.
   WARNING!: Users who disassemble Electrical Self-balancing Vehicles without permission will void the warranty
   WARNING: Risk of Fire -No User Serviceable Parts 9.Electrical Self- balancing Vehicles Parameters

Electrical Self-balancing Vehicles Parameter

Model| W3665PA| Battery| Lithium-ion
Parameter| 606×210 xl86| Battery voltage| 36V
Net Weight| 7.3 ± 0.1 kg| Maximum battery voltage| 42V
Maximum load weight| 75 kg| Battery capacity| 2Ah
Minimum load weight| 20kg| Input current| 0.4A
Maximum speed limit| 10 km/h| Output current| I 0A
Maximum.Range| 6.5 km| levels of enclosure protection| ?: IP34
Max climbing limit| 10°| Charger Type| HLT-118A-4200400 … FYO184200400
Mini1nal turning radius| zero| Charger rate| DC 42V, 0.4A
Ground clearance| 23±3mm| Charging time| 5 hours
Platform height| 113±5 mm| Tire| 6.5 inches
Storage temperature| Within 3 moths:0°C – 35 °C Within 1 year:25 °C| Install balancing device| YES
Operating temperature| -10- 40°C| Charge temperature| 0-40°C
Power requirement| ACI00-240V/50-60HZ| |
Circuit Board Parameter

Model| YK190A| Voltage| DC 36V
Max Test Voltage| DC43V| Maximum Current| 13±1A
Low-air Warning Voltage| DC 34 ± 0.SV| Service Frequency| 16k

Packing List

Packing List

Number| Product Name| Quant ity
1| Electrical Self -Balancing vehicle| I
2| Charger| I
3| instructions| I

Troubleshooting

Electrical Self-balancing Vehicles has a self-examination function, such as sensors, the system static current, system dynamic current, motor speed fluctuation, etc.
You can contact our service department to solve problems.

common faults

closed
7| indicator flashes seventh.then turns off| the question of communicate| Loop until closed
8| indicator flashes ninth,then turns off| Baseplate ang le of  inclination more than 80•| Loop until closed

**Enjoy your Electrical Self-balancing Vehicles!**

Documents / Resources

| DOC W3665A Spider Electrical Self-Balancing Vehicles [pdf] Instruction Manual
W3665A Spider Electrical Self-Balancing Vehicles, W3665A, Spider Electrical Self-Balancing Vehicles, Electrical Self-Balancing Vehicles, Self-Balancing Vehicles, Vehicles
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>