Panasonic ES-ST37 Rechargeable Shaver Instruction Manual

Panasonic ES-ST37 Rechargeable Shaver

Thank you for purchasing this Panasonic product. Before operating this unit, please read these instructions completely and save them for future use.

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

DANGER: Denotes a potential hazard that will result in serious injury or death.
WARNING: Denotes a potential hazard that could result in serious injury or death.
CAUTION: Denotes a hazard that could result in minor injury.The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users to a specific operating procedure that must not be performed. This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

WARNING

• This shaver has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment.
• Doing so may cause overheating, ignition, or explosion.
• Do not connect or disconnect the adaptor to a household outlet with a wet hand.
• Doing so may cause electric shock or injury.
• Do not immerse the AC adaptor and the charging stand in water or wash with water.
• Doing so may cause electric shock or fire due to a short circuit.
• Do not place the AC adaptor and the charging stand over or near water filled sink or bathtub.
• Doing so may cause electric shock or fire due to a short circuit.
• Do not use anything other than the supplied AC adaptor and the charging stand for any purpose.
• Also, do not use any other product with the supplied AC adaptor and the charging stand. (See page 8.)
• Doing so may cause burn or fire due to a short circuit.
• Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet.
• Doing so may cause electric shock or fire due to a short circuit.
• Do not damage, modify, or forcibly bend, pull, or twist the cord.
• Also, do not place anything heavy on or pinch the cord.
• Doing so may cause electric shock or fire due to a short circuit.
• Do not use in a way exceeding the rating of the household outlet or the wiring.
• Exceeding the rating by connecting too many plugs to one\ household outlet may cause fire due to overheating.
• Do not modify or repair.
• Doing so may cause fire, electric shock, or injury.
• Contact an authorized service center for repair (battery change, etc.).
• Do not store within reach of children or infants. Do not let them use it.
• Putting the inner blades, the cleaning brush and/or the oil container in the mouth may cause accidents and injury.
• Never disassemble except when disposing of the product.
• Doing so may cause fire, electric shock, or injury.
• Always unplug the adaptor from a household outlet when cleaning.
• Failure to do so may cause electric shock or injury.
• Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor.
• Fully insert the adaptor.
• Failure to do so may cause fire or electric shock.
• Regularly clean the power plug and the appliance plug to prevent dust from accumulating.
• Failure to do so may cause fire due to insulation failure caused by humidity.
• Disconnect the adaptor and wipe with a dry cloth.
• Immediately stop using and remove the adaptor if there is an abnormality or malfunction.
• Using it in such conditions may cause fire, electric shock, or injury.
• Abnormality or malfunction cases
• The main unit, adaptor or cord is deformed or abnormally hot.
• The main unit, adaptor or cord smells of burning.
• There is abnormal sound during use or charging of the main unit, adaptor or cord.
• Immediately request inspection or repair at an authorized service center.
• If the oil is consumed accidentally, do not induce vomiting, drink a large amount of water, and contact a physician.
• If the oil comes into contact with eyes, immediately wash thoroughly with running water, and contact a physician.
• Failure to do so may result in physical problems.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Failure to do so may cause an accident or injury.
• The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.
• Failure to do so may cause an accident or injury.

CAUTION

• Do not allow pins or trash to adhere to the power plug or the appliance plug.
• Doing so may cause electric shock or fire due to a short circuit.
• Do not use excessive pressure to apply the system outer foil to your lip or other part of your face. Do not apply the system outer foil directly to blemishes or injured skin.
• Doing so may cause injury to the skin.
• Do not forcefully press the system outer foil. Also, do not touch the system outer foil with fingers or nails when in use.
• Doing so may cause injury to skin or reduce the life of the system outer foil.
• Do not touch the blade section (metallic section) of the inner blade.
• Doing so may cause injury to your hands.
• Do not use this product for hair on head or any other part of the body.
• Doing so may cause injury to skin or reduce the life of the system outer foil.
• Do not share your shaver with your family or other people.
• Doing so may result in infection or inflammation.
• Do not drop or subject to shock. – Doing so may cause injury.
• Do not wrap the cord around the adaptor or the charging stand when storing.
• Doing so may cause the wire in the cord to break with the load, and may cause fire due to a short circuit.
• Disconnect the adaptor from the household outlet when not charging.
• Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.
• Check the system outer foil for cracks or deformations before use.
• Failure to do so may cause injury to the skin.
• Be sure to place the shaver in its carrying holder when carrying around or storing.
• Failure to do so may cause injury to skin or reduce the life of the system outer foil.
• Disconnect the adaptor or the appliance plug by holding onto the adaptor or the appliance plug instead of the cord.
• Failure to do so may cause electric shock or injury.

Disposing of the rechargeable battery

DANGER

• The rechargeable battery is exclusively for use with this shaver. Do not use the battery with other products.
• Do not charge the battery after it has been removed from the product.
• Do not throw into fire or apply heat.
• Do not hit, disassemble, modify, or puncture with a nail.
• Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.
• Do not carry or store the battery together with metallic jewelry such as necklaces and hairpins.
• Do not charge, use, or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.
• Never peel off the tube.
• Doing so may cause overheating, ignition, or explosion.

WARNING

• After removing the rechargeable battery, do not keep it within reach of children and infants.
• The battery will harm the body if accidentally swallowed. If this happens, consult a physician immediately
• If the battery fluid leaks out, take the followingprocedures. Do not touch the battery with your bare hands.
• The battery fluid may cause blindness if it comes in contact with your eyes.
• Do not rub your eyes. Wash immediately with clean water and consult a physician.
• The battery fluid may cause inflammation or injury if it comes in contact with the skin or clothes. Wash it off thoroughly with clean water and consult a physician.

Important information

• This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.

Notes

• Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.
• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.
• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.
• Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals.
• Store the shaver in a place with low humidity after use.
• Do not store the shaver where it will be exposed to direct sunlight or other heat sources.
• The following symbol indicates that a specific detachable power supply unit is required for connecting the electrical appliance to the supply mains.
• The type reference of power supply unit is marked near the symbol.
• Charge the appliance correctly according to these Operating Instructions. (See page 9 “Charging the shaver”.)
• This appliance contains battery that is only replaceable by skilled persons. Please contact an authorized service center for the details of repair.

Parts identification

Main body

1. System outer foil
2. Foil frame
3. Foil frame release buttons
4. Cleaning shutter
5. Finger rest
6. Side terminals
7. Power switch
8. Shaving sensor lamp ( )
9. Charge status lamp ( )
10. Inner blades
11. Trimmer
12. Trimmer handle
13. Outer foil section
14. System outer foil release buttons
15. Water inlet

AC adaptor (RE7‑59)

(The shape of the AC adaptor differs depending on the area.)

1. Adaptor
2. Power plug
3. Cord
4. Appliance plug

Charging stand (RC9‑83)

1. Charging terminals
2. Stand socket

Accessories

1. Carrying holder
2. Cleaning brush
3. Oil
4. Travel pouch

Before use

Using the carrying holder

The shaver can be kept vertically or horizontally. When transporting the shaver, you can use the carrying holder to protect the outer foil and prevent erroneous operation of the switch.

• When transporting the shaver, be sure to clean off any shavings before attaching the carrying holder.

Attaching the carrying holder

• Attach the carrying holder as illustrated.
• Securely attach the carrying holder to the main unit.

Removing the carrying holder

• Remove the carrying holder while pressing down on both sides.

Charging the shaver

You can charge the shaver with the carrying holder attached.

1. Insert the appliance plug into the stand socket.
2. Insert the shaver in the charging stand as illustrated.
   • The shaver will not charge unless the side terminals (a) are in contact with the charging terminals (b).
   • Wipe off any water droplets on the side terminals.
3. Plug in the adaptor into a household outlet and check that the charge status lamp ( ) glows.
   • Charging is completed after approx. 1 hour. The charging time may decrease depending on the charging capacity.

• After charging is completed, turning the power switch ON with the shaver plugged in will cause charge status lamp ( ) to light up and then turn off after 5 seconds. This shows that the shaver is fully charged.
• Recommended ambient temperature for charging is 10 – 35 °C. It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.
• The charge status lamp ( ) will blink twice every second when there is a problem with charging. Charge the shaver within the recommended ambient temperature range.
• When charging the shaver for the first time or when it has not been in use for more than 6 months, the charge status lamp ( ) may not glow. It will eventually glow if kept connected.

Disconnect the adaptor after charging is completed

• Charging the battery for more than 1 hour will not affect battery performance.

Note: You cannot operate the shaver while charging.

Making foam

• It is easier to make foam this way than by hand.
• After using the shaver in shaving foam mode, always rinse the main body with water and apply oil to the blades. (See page 13.)

Usable facial cleansers, etc

Shaving agent

| Shaving foam|
---|---|---
Shaving gel|
Shaving cream|

Facial cleanser

| Facial cleansing foam

(without scrubbing compounds)

| ****
Facial cleansing foam

(with scrubbing compounds)

|
Facial soap|

Body soap etc.

| Liquid| ****
Foam|

1. Take an appropriate amount of facial cleanser etc. in the palm of your hand.
2. Add an appropriate amount of water or hot water.
3. Hold the power switch for 2 seconds or more to switch to shaving foam mode.

• The shaving sensor lamp ( ) and charge status lamp ( ) blink alternately.

• After 15 seconds in shaving foam mode, the shaver switches automatically to shaving sensor mode. (See this page.)

• Press the power switch during shaving foam mode to switch to shaving sensor mode.

1. Press the blades gently in the palm of your hand, mix the facial cleanser etc. around and move the blades up and down to make foam.

• If there is insufficient foam, add slightly more water, hot water or facial cleanser etc. to make it easier to create foam.

Notes

• Before making foam, check that the blades are not broken or deformed, and that the cleaning shutter is closed.
• Do not use shaving agent (excluding foam), facial cleansing foam (with scrubbing compounds) or soap as these may cause the blades to clog, or be unable to make foam.

Using the shaver

1. Press the power switch to select the desired shaving mode.

• Each time you press the power switch, the shaving mode changes from “Shaving sensor mode” “Normal mode” “OFF.”

• The shaving sensor may not respond depending on the thickness of the beard or the type of the shaving gel, but this is normal.

1. Hold the shaver as illustrated and shave.

• Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

• You can also use a pen grip to hold the shaver.

Using the trimmer

• Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns.

Notes

• Before shaving, check that the cleaning shutter is closed.
• Place your finger on the finger rest while in use. Keeping your finger placed on the power switch during use may switch the mode or turn the shaver OFF.
• Do not use shaving creams or face cleansers containing scrubbing compounds as these may cause the outer foil to clog.
• The appliance may not operate in an ambient temperature\ approximately 5 °C or lower.

Reading lamps when using

• When the battery capacity is low

• The charge status lamp ( ) blinks once every second when operating the shaver.

• You can shave 2 to 3 times after the charge status lamp ( ) blinks. (This will differ depending on usage.)

• A full charge will supply enough power for approx. 14 shaves of 3 minutes each.

• If the shaver is operated in the shaving sensor mode in a battery‑shortage condition, the shaving sensor lamp ( ) glows blue, and the charge status lamp ( ) blinks red.

Cleaning the shaver

1. 1Remove the shaver from the charging stand.
2. Apply some hand soap and some water to the outer foil.
   • Close the cleaning shutter.
3. Turn the shaver on.

• There are two ways to clean the shaver, depending on the actual dirt level.

1. Slide the cleaning shutter until it clicks.

2. Clean the outer foil section with running water.

3. Turn the shaver off.

• Rinse with water and shake up and down several times to remove the water.

|

1. Turn the shaver off after 10 – 20 seconds.

2. Remove the outer foil section and turn the shaver on.

3. Clean the shaver and the outer foil section with running water.

•  Rinse with water and shake up and down several times to remove the water.

• Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction.

1. Wipe off any drops of water with a dry cloth.
2. Dry the outer foil section and the shaver completely in a shaded area.
   • The outer foil section will dry faster ifremoved from the main body.
3. Attach the outer foil section to the shaver.
4. Lubricate the shaver. (See this page.)

Lubrication
To maintain shaving comfort for a long time, it is recommended that the oil provided with the shaver is used.

1. Switch off the shaver.
2. Apply one drop of oil to each of the outer foils.
3. Raise the trimmer and apply a drop of oil.
4. Switch the shaver on, and run it for approximately five seconds.
5. Switch off the shaver, and wipe off any excess oil from the outer foils with a soft cloth.

Cleaning with the brush

Cleaning with the long brush

• Clean the system outer foil (a), the shaver body (b) and the trimmer (c) using the long brush.

Cleaning with the short brush

• Clean the inner blades using the short brush by moving it in direction (A).
• Do not move the short brush in direction (B) as it will damage the inner blades and affect their sharpness.
• Do not use the short brush to clean the outer foils.

Replacing the system outer foil and the inner blades

Removing the outer foil section

• Press the foil frame release buttons and lift the outer foil section upwards.

Attaching the outer foil section

• After turning the water inlet surface to the front, securely attach the outer foil section to the shaver until it clicks.

Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.
2. Align the water inlet surface and the system outer foil mark ( ) and securely attach together.
   • The system outer foil cannot be reversely attached.
   • Always insert the system outer foil to the foil frame when attaching to the shaver.

Replacing the inner blades

1. Remove the inner blades one at a time.
   • Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand.
2. Insert the inner blades one at a time until they click.

Replacement parts

• Replacement parts are available at your dealer or Service Center.

Troubleshooting

If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.

Battery life

The life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers. Have the battery replaced by an authorized service center.

Removing the built-in rechargeable battery

Remove the built-in rechargeable battery before disposing of the shaver

The battery is to be disposed of safely. Please make sure that the battery is disposed of at an officially designated location if there is one. This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the charging stand.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
• Perform steps 1 to 6 and lift the battery, and then remove it.
• Please take care not to short-circuit the battery.

For environmental protection and recycling of materials

This shaver contains a Lithium‑ion battery. Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country.

Specifications

Power source| See the name plate on the AC adaptor. (Automatic voltage conversion)
---|---
Motor voltage| 3.6 V
Charging time| Approx. 1 hour

This product is intended for household use only.

Panasonic Corporation

http://www.panasonic.com

© Panasonic Corporation 2015-2020

References

• Panasonic North America | Create Today, Enrich Tomorrow

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>