greasetek 165830 Grease Gun User Manual

June 3, 2024
GreaseTek

greasetek LOGO

greasetek 165830 Grease Gun

greasetek 165830 Grease Gun

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or maintain this product.

WARNING Improper operation or maintenance of this tool could result in serious injury and property damage.
Read and understand all warnings and operation instructions before using this tool. When using any tool, basic safety precautions should always be followed to reduce the risk of personal injury. Use each tool for its intended function only. Do not use this product in unsafe work conditions. It is always recommended to keep a fire extinguisher and first aid kit near work areas.

FAILURE TO OBSERVE AND FOLLOW SAFETY INSTRUCTIONS COULD RESULT IN INJURY OR DEATH.
WARNING This product may contain a chemical known to the state of California to cause cancer, or birth defects or other reproductive harm.

RISK OF PERSONAL INJURY

**WARNING RISK OF PERSONAL INJURY**

WHAT COULD HAPPEN| HOW TO PREVENT IT
Eyes and face can come into direct contact with grease, causing serious injury.| Do not allow grease to come in to direct contact with eyes. Do not ingest grease.

Never aim or pump grease at yourself or anyone else.

Always wear ANSI approved Z87.1 safety glasses with side shields, appropriate face mask, gloves and protective clothing.

Always operate in a well ventilated area to prevent health and fire hazards.

If eyes or face come into direct contact with grease, contact your local doctor or emergency room for immediate help.

Pumping improper materials or materials not intended for gun application could result in serious injury or death.| Do not pump anything but grease with this tool.

Always read the label or Materials Safety Data Sheets (MSDS) for the materials before use to ensure they are safe to use.

greasetek 165830 Grease Gun 1

PACKAGE CONTENTS

greasetek 165830 Grease Gun 2

PREPARATION

Before assembling this tool, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the tool.
Estimated Assembly Time: 3 – 5 minutes
Tools and Materials Required for Assembly (not included):

  • Adjustable wrench (optional)
  • Grease (bulk or cartridge)
  • Clean rag/lint-free cloth

ASSEMBLY INSTRUCTIONS

  1. Remove retaining ring from trigger (See Figure A).
  2. Screw the extension (E) with coupler (F) securely onto the head (B) by aligning threads and turning clockwise. If necessary, tighten with adjustable wrench but do not overtighten (See Figure B and C).

greasetek 165830 Grease Gun 3

  1. Flex hose being screwed into front port just like “B” and “C” above.
  2. Flex hose and extension pipe being attached to the top of the grease gun (See Figure D).

TO CHANGE LOCATION OF EXTENSION TUBE OR FLEX HOSE

  • Remove extension tube or flex hose from grease gun.
  • Remove top plug (J) and screw into front outlet (K).
  • Screw the extension tube or flex hose into the top inlet (J) (See Figure D).

GREASE LOADING INSTRUCTIONS

CAUTION
Use caution when loading grease to prevent damaging substances (dirt, metal shavings or particles, etc.) from contaminating the grease.
There are two methods for loading grease:

Method 1: Grease Cartridge Loading (most common)
Method 2: Grease Tub Loading (from bulk container)

METHOD 1: GREASE CARTRIDGE LOADING

  1. Unscrew the barrel (A) from the head (B) by turning counterclockwise.
  2. Holding the barrel securely with one hand, pull the plunger (C) all the way out. Make sure it locks into place before relaxing your grip on the barrel or plunger.
  3. To prepare the grease cartridge, first remove the plastic lid from one end, then insert the cartridge (open end first) all the way into the barrel. The metal pull-tab lid will be visible.
  4. Remove the metal pull-tab lid. Make sure no metal slivers fall into the grease.
  5. With the grease cartridge fully inserted, screw the barrel back on the head by turning clockwise and tighten by hand (See Figure 5).
  6. Carefully release the plunger by pressing down on the spring plunger release (G). After releasing the plunger, press the air bleed button (H) to purge any excess air in the barrel (See Figure 6).
  7. Pump the trigger until grease begins to flow from the coupler (F). It will take several pumps until grease begins to flow. If grease does not flow, make sure the plunger is free to push grease up the barrel by pressing the spring pluger release (G). Press the air bleed button (H) as you release it to purge any excess air. Repeat until grease flows correctly (See Figure 6).

greasetek 165830 Grease Gun 4

NOTE: Trapped air and air bubbles in the grease are the most common causes of poor grease flow.
Always purge trapped air using the air bleed button before using the gun.

METHO D 2: GREASE TUB LOADING
With close-fitting plastic washer covering grease in tub.

  1. Unscrew the barrel (A) from the head (B) by turning counterclockwise (See Figure 7).
  2. Place the tub of grease where you can use the grease gun barrel to push down on the close-fitting plastic washer while pulling back on the plunger (C) at the same time (See Figure 8).
  3. Line up the open end of the barrel over the hole in the washer. Holding the barrel securely with one hand, use it to push down on the washer while pulling back on the plunger at the same time. Grease will be forced up through the hole in the washer and sucked into the grease gun barrel (See Figure 8).
  4. When the grease gun barrel is full, slide it sideways to “cut off” the pillar of grease you’ve made inside the barrel (See Figure 9)
  5. Screw the barrel back on the head by turning clockwise and tighten by hand (See Figure 10).
  6. Carefully release the plunger by pressing down on the spring plunger release (G). After the plunger slides into the barrel, press the air bleed button (H) to purge any excess air in the barrel and allow grease to flow freely (See Figure 11).
  7. Pump the trigger until grease begins to flow from the coupler (F). It will take several pumps until grease begins to flow. If grease does not flow, make sure the plunger is free to push grease up the barrel by pressing the spring plunger release (G). Press the air bleed button (H) as you release it to purge any excess air. Repeat until grease flows correctly (See Figure 11).

greasetek 165830 Grease Gun 5

NOTE: Trapped air and air bubbles in the grease are the most common causes of poor grease flow. Always purge trapped air using the air bleed button before using the gun.

OPERATING INSTRUCTIONS

CAUTION :

  • Always make sure the dispensing nozzle or coupler (F) is clean before using. Pump out a small amount of grease, then wipe off with a clean rag or lint-free cloth before attaching to the grease fitting to be lubricated.
  • Always make sure grease fittings are clean before lubricating. Clean away all dirt before attaching the grease gun, even if grease fitting caps are used. Inspect and replace damaged fittings.
  • Clean grease fittings after applying grease.
  • Ensure the proper type of grease is used at every grease point. Applying the wrong grease can cause incompatibility problems and lead to bearing failure. Use colored labels, adhesive dots, or paint markers to identify which type of grease should be used on various lubrication points.

greasetek 165830 Grease Gun 6

  1. The grease coupler provided at the end of the grease gun extension has small “jaws” that snap on to a grease fitting and maintain a tight fit.
    To connect the coupler to a grease fitting, press the coupler straight onto the fitting to form a snug fit. Always keep the extension and coupler straight on to the grease fitting when pumping grease.

  2. To remove, slightly tilt the coupler until resistance is felt, then twist and pull back. This tilt-and-twist movement will allow the coupler to properly detach from the grease fitting.

greasetek 165830 Grease Gun 7

If coupler is difficult to remove, loosen grease coupler a 1/4 turn or until jaws have relaxed their grip enough to remove the grease coupler from the grease fitting.

WARNING Disengaging the coupler by pulling it out straight could break grease fitting.

CARE AND MAINTENANCE

Use a wet towel to clean the grease gun head, barrel and parts after each use, and dry it thoroughly. Make sure the tool is properly cleaned and that there are no contaminates on it before storing. STORAGE
Grease guns should be stored unpressurized in a horizontal position, in a clean, cool dry area to help prevent grease from separating. Grease gun clamps are recommended (not included) to make storage simpler and safer.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Gun will not dispense grease Grease cartridge or barrel is empty
Air is trapped in the head Replace the grease cartridge or refill the barrel

Make sure plunger is free to push grease up the barrel. Press air bleed button.

Grease leaks out of bottom of barrel around plunger| Damaged/worn rubber follower| Replace grease gun
Grease leaks out where extension is attached to head| Loose connection| Tighten connection. Apply thread sealant tape to threads and

re-connect.

Grease leaks out around

coupler

| Damaged coupler| Replace coupler

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals