GAINSBOROUGH K418 Solar Light Up Bunting Red White and Blue Instructions

: June 3, 2024
: GAINSBOROUGH

Table of Contents

Dimensions
ASSEMBLY INSTRUCTIONS / INSTRUCTIONS FOR USE
MAINTENANCE AND TROUBLESHOOTING:
- CARE AND MAINTENANCE RECOMMENDATIONS
BATTERIES
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GAINSBOROUGH K418 Solar Light Up Bunting Red White and Blue Instructions

Dimensions

12m in length

Material
Polyester

Batteries required: 1 x AA 300mAh rechargeable battery (provided)

40 PIECES OF BUNTING, 15CM APART
WITH 80 LEDS IN RED WHITE & BLUE RUNNING ALONG THE BUNTING POWERED BY A SOLAR PANEL

KEEP AWAY FROM POWER LINES AND HEAT SOURCES

ASSEMBLY INSTRUCTIONS / INSTRUCTIONS FOR USE

Unpack the components carefully. Please check all parts have been removed from the packaging.

Before using first time

Remove the protective film from the solar panel. Allow solar panel to charge for at least 8 hours in full sunlight with the ON/OFF switch in the ON position. The ON/OFF switch is located on the back of the solar panel. Once the batteries are fully charged, set the ON/OFF switch to ON. If the lights do not turn on after dark refer to Maintenance section.
NOTE: In order to test the lights simply cover the solar panel with your hand and the light should turn on automatically.

Find an ideal Place for the Solar Light.

Place the solar panel in an area where it will receive direct sunlight for at least 8 hours per day. The number of hours the light will illuminate is directly proportional to the hours of sunlight it receives. If the panel is laced in a shaded area, it will not be able to fully charge and its illumination time will be limited. Do not place the panel near other outdoor lighting like porch or streetlights. These may fool the sensor and keep the lights from coming on, or cause them to turn off automatically.

MAINTENANCE AND TROUBLESHOOTING:

Make sure the switch is set to “ON” position.
Keep the solar panel clean.
If solar product does not light up after it has been used for around 8 – 12 months, replace the rechargeable battery as it may be weak or worn out. (Battery 1x AA 1.2v 300Mah, Ni-MH, Rechargeable– Same equivalent type as recommended must be used).
Battery replacement:
Step 1: Unscrew the battery compartment cover by using a Phillips head screwdriver (not included).
Step 2: Remove the exhausted battery and install 1x new AA rechargeable battery according to the +/- polarity as beside image. Open the compartment carefully and ensure that wire inside the battery terminals is not damaged.
Step 3: Replace battery compartment cover, screw it back into position and make sure is properly sealed.
Step 4: Charge battery under direct sunlight for at least 8 hours.

CARE AND MAINTENANCE RECOMMENDATIONS

Clean solar panel with a soft sponge every couple of weeks.
Make sure all connectors are still tight and no water getting in.

BATTERIES

Keep batteries away from children and pets.
Do not mix used and new batteries.
Remove the batteries if left for long periods.
Never dispose of batteries in a fire.
Battery disposal, spent or expired batteries must be properly disposed of and recycled in compliance with local regulations. For detailed information, contact your local authority.
Follow the battery manufacturer’s safety, usage, and disposal instructions.

DISPOSAL

Coopers of Stortford use recyclable or recycled packaging where possible.
Please dispose of all packaging, paper, cartons, packaging in accordance with your local recycling regulations.
Plastics, polybags – this is made from the following recyclable plastic.

Code & Symbol| |
---|---|---
Type of Plastic| Polypropylene| Please Specify (includes ABS, Nylon)
Commonly used for| Microwaveable food containers, yoghurt pots, butter tubs, disposable plates and cups| CD’s, crisp packets, various flexible packaging, baby bottles, sunglass lenses
Notes| Commonly recycled and collected from household recycling bins (packaging tape itself not recyclable but does not interfere with cardboard)| Not often or widely recycled