LUCCI 028120 Orbit LED Pendant Instruction Manual

LUCCI 028120 Orbit LED Pendant

Warranty

• This luminaire is covered by a 3-year warranty. The warranty is from the date of purchase, not the date of installation.
• If the luminaire is not installed by a licensed electrician, it will void the warranty.
• Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
• The use of non-compatible dimmers may damage your LED light fitting and will void the warranty.
• Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation requirements

• • Must be assembled and installed by a licensed electrician.

• This luminaire is a Class I product and must be earthed during wiring and installation.

• All wiring and installation of the light fitting must adhere to local and national wiring rules. E.g. AS/NZS 3000 Electrical installations.

• Select a suitable location for installation:

  •  This product is suitable for indoor use only.
  •  The mounting point must support 2 times the weight of the luminaire.
  •  Ensure the luminaire is not installed next to any air vent system.
  •  When installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and therefore not covered under warranty.

• This luminaire is dimmable and has been tested at the date of publication with the dimmers listed in the specification section. The use of a LED dimmer such as the Lucci LEDlux SKU# 290998 or SKU# 290997 or SKU# 290443 dimmer is highly recommended.
  NOTE: For the best dimming range, use the Lucci LEDlux SKU# 290998 dimmer and adjust the variable resistor at the minimum and maximum dimming positions on the dimmer during the installation.
  NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED light startup or slight uneven light performance when more than one LED luminaire is linked together, switched ON or dimmed. This is not a product fault and therefore not covered under warranty.
  NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the LED light and adjust the dimmer down to your desired light level.
  NOTE: Testing cannot account for installation variables such as variation in mains supply voltage, cable capacitance, electrical noise, transients, surges and ripple control signals (commonly found in NSW & QLD).
  NOTE: The information provided is correct to the best of Beacon Lighting’s knowledge at the date of publication.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

• Lay out all the components on a smooth surface and make sure there are no components are missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement. Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation directions

Due to the size of the luminaire, two people will be required to lift it during the installation process.

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.

1.  Remove the mounting bracket from the canopy by loosening the screws. Use the mounting bracket as a template to mark the screw positions on the wall.

2.  Install the mounting bracket onto the wall by using appropriately sized mounting screws and anchors. Ensure the screws and anchors used are suitable for the mounting surface.
   

3. Connect the mains supply wire to the terminal block.
   
   Ensure the wires are secure and no bare wires are exposed.

4.  Determine the suspension length required for your installation location. Press the cord anchorage and then adjust the length of the cords. Ensure the rest of the suspension wires are tighten & well placed inside the canopy.

5.  Attach the canopy onto the mounting bracket and secure it by tightening the screws.

6.  After the installation, switch on the luminaire to test and enjoy your new lighting product.

This product has a colour switching function (2700K / 4000K / 5500K):
NOTE: If the luminaire is installed with dimmer, it is recommended to turn the dimmer to the highest position before adjusting the colour temperature as below.

•  Turn on the luminaire for the first time; the luminaire will switch to colour temperature 2700K.
•  Turn off the luminaire, then turn it on again within 3 seconds; the luminaire will switch to colour temperature 5500K.
•  Turn off the luminaire, then turn it on again within 3 seconds; the luminaire will switch to colour temperature 4000K.
•  If the luminaire is turned off for more than 7 seconds, it will keep the same colour temperature as it was last on.
•  The colour temperature will reset to 2700K if the switch is turn on/off quickly twice within 1 second.

Safety tips

• Always ensure the power is switched OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
• To clean, wipe with a damp clean cloth. Do NOT soak or immerse the luminaire in water or other l iquids.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>