TAC 3B-F102T Bull Bar Instruction Manual

TAC 3B-F102T Bull Bar Instruction

Product Information

Specifications:

• Model: 3 BULL BAR
• Compatibility: 2004-2024 Ford F150 (Excl. Heritage edition/all F150 Raptor models/2020-2022 Diesel models), 2022-2024 F150 lightning EV, 2003-2017 Expedition
• Part Number: 3B-F102T
• Website: www.tacautoparts.com

Product Usage Instructions

Installation Instructions:

1. Vehicles with Factory Tow Hooks:
   • Remove tow hooks by loosening the rear bolt and removing the front bolt.
   • Position the Mounting Bracket under the frame and secure it with factory tow hook bolts and double nut plate.
2. Vehicles with closed ends on the front of the frame:
   • Insert U-Bolt on the driver side, secure the Mounting Bracket to the U-Bolt, and tighten hardware.
   • Repeat the process for the passenger side Mounting Bracket installation.
3. Position the Bull Bar inside the Mounting Brackets and attach it using provided hardware. Align and tighten all hardware.
4. Do periodic inspections to ensure all hardware is secure and tight.

Maintenance Instructions:

To protect your investment, wax the product after installing. Regular waxing is recommended for added protection. Avoid using abrasive polishes or waxes that could damage the finish. For CV stainless steel, use aluminium polish for scratches. Clean with mild soap.

FAQ

• Q: Is this Bull Bar compatible with all Ford F150 models?
  A: The Bull Bar is compatible with 2004-2024 Ford F150 models excluding Heritage Edition, all F150 Raptor models, and 2020-2022  Diesel models.

• Q: Can I reinstall the factory tow hooks after installing the Bull Bar?
  A: No, this Bull Bar is not compatible with the factory tow hooks, so they should not be reinstalled after installation.

INSTALLATION INSTRUCTIONS

3” BULL BAR 2004-2024 Ford F150
(Excl. Heritage edition/all F150 Raptor models/2020-2022 Diesel models) 2022-2024 F150 lightning EV | 2003-2017 Expedition PART# 3B-F102T

PARTS LIST

frames” only)
4| 12mm x 40mm Bolt Plates| 4| 10mm x 27mm OD x 3mm Flat Washers
4| 12-1.75mm x 35mm Hex Head Bolts| 4| 10mm Lock Washers
8| 12mm Lock Washers| 4| 10mm Hex Nuts

4

| 12mm x 24mm OD x 2.5mm Flat Washers (for Mounting Bracket to frame)|  |

PROCEDURE

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
   NOTE : It may be necessary to remove/relocate the front license plate and license plate bracket. It is not required but strongly recommended. If local/state law requires a license plate, license plate relocation kit is available.
   NOTE : It may be necessary to remove the lower plastic portion of the bumper to gain access to the ends of the frame rails. The indented pockets in the lower bumper will need to be cut out to allow the Mounting Brackets to pass through.

2. Vehicles with Factory Tow Hooks
   Remove tow hooks by removing the front bolt and only loosening the rear bolt. Slide the tow hooks off. Keep the factory double nut plate in the frame and aligned with the holes.
   NOTE : This Bull Bar is not compatible with the factory tow hooks, so you will not be reinstalling the tow hooks.
   Position the Mounting Bracket up to the bottom of the frame and secure it with the factory tow hook bolts and factory double nut plate, (Figure 1).
   Vehicles without Tow Hooks
   Starting on the driver side of the vehicle, insert (1) 12mm Bolt Plate through the opening in the open front end of the frame and down through the rear hole in the bottom of the frame, (Figure 2). Thread (1) 12mm x 24mm OD x 2.5mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut onto the threaded end of the Bolt Plate. Slide the slotted end of the driver side Mounting Bracket under the nut and washers. Insert the second  12mm Bolt Plate through the remaining hole toward the front of the Mounting Bracket. Secure with (1) 12mm Lock Washer, (1) 12mm x 24 mm OD x 2.5mm Flat Washer and (1) 12mm Hex Nut. Snug but do not tighten the hardware at this time.
   Vehicles with “closed ends” on the front of the frame
   Starting on the driver’s side of the vehicle, locate the two holes on the bottom of the frame. Insert (1) 10mm U-Bolt into one hole and out the other, (Figure 3A & 3B). Hold the driver-side Mounting Bracket in position with the slotted end toward the rear. Secure the Mounting Bracket to the U-Bolt with (2) 10mm x 27mm OD x 3 mm Flat Washers, (2) 10mm Lock Washers and (2) 10mm Hex Nuts, (Figure 4). Snug but do not tighten the hardware

3. Repeat the appropriate Step 3 for the passenger side Mounting Bracket installation.

4. With help position the Bull Bar on the inside of the Mounting Brackets. Use the included (4) 12mm x 35mm Hex Bolts, (4) 12mm lock Washers, (8) 12mm Flat Washers and (4) 12mm Hex
   Nuts to attach the Bull Bar to the Mounting Brackets, (Figure 5). Do not tighten at this time.

5. Align and adjust the Bull Bar properly, and tighten all hardware.

6. Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish.
Mild soap may be used also to clean the Bull Bar.
For gloss black finishes: Mild soap may be used to clean the Bull Bar.

Driver Side Installation Pictured

References

• TACUSA
• TACUSA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>