Sage BJS700 Big Squeeze Slow Compression Juicer User Guide

: June 3, 2024
: Sage

Table of Contents

Sage BJS700 Big Squeeze Slow Compression Juicer
IMPORTANT SAFEGUARDS
Components
- Rating Information
Assembly
Operation
Care & Cleaning
Troubleshooting
Guarantee
CONTACTS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sage BJS700 Big Squeeze Slow Compression Juicer

Sage-BJS700-Big-Squeeze-Slow-Compression-Juicer-
product

SAGE® RECOMMENDS SAFETY FIRST

At Sage® we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

A downloadable version of this document is also available at sageappliances.com
Before using it for the first time ensure your electricity supply is the same as shown on the label on the underside of the appliance.
Remove and safely discard any packaging materials before first use.
To eliminate a choking hazard for young children, safely discard the protective cover fitted to the power plug.
This appliance is for household use only. Do not use the appliance for anything other than its intended use. Do not use in moving vehicles or boats.
Do not use outdoors. Misuse may cause injury.
Fully unwind the power cord before operating.
Position the appliance on a stable, heat-resistant, level, dry surface away from the edge and do not operate on or near a heat source such as a hot plate, oven or gas hob.
Vibration during operation may cause the appliance to move.
Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.
Always ensure the appliance is turned OFF, unplugged at the power outlet and has been allowed to cool before cleaning, attempting to move or storing.
Always turn the appliance to the OFF position, switch it off at the power outlet and unplug at the power outlet when the appliance is not in use.
Do not use the appliance if the power cord, plug, or appliance becomes damaged in any way. If damaged or maintenance other than cleaning is required, please contact Sage Customer Service or go to sageappliances.com
Any maintenance other than cleaning should be performed by an authorised Sage® service centre.
Children should not play with the appliance.
Cleaning of the appliance should not be carried out by children unless they are 8 years or older and supervised.
The appliance and its cord should be kept out of reach of children aged 8 years and younger.
The installation of a residual current safety switch is recommended to provide additional safety when using all electrical appliances.
Safety switches with a rated operating current of not more than 30mA are recommended. Consult an electrician for professional advice.
Always ensure the appliance is properly assembled before use.
The appliance will not operate unless properly assembled.
Do not use the appliance on a sink drainboard.
Keep hands, fingers, hair, clothing as well as spatulas, and other utensils away from moving or rotating parts during operation.
Do not use the appliance for anything other than food and/or beverage preparation.
In order to avoid the possible hazard of the appliance starting by itself due to inadvertent resetting of the overload protection, do not attach an external switching device (such as a timer) or connect the appliance to a circuit that can regularly switch the appliance on and off.
Carefully read all instructions before operation and save them for future reference.
The appliance can be used by persons with reduced physical or mental capabilities or a lack of experience and knowledge, only if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
This appliance shall not be used by children.
Do not leave the appliance unattended when in use.
Do not push food into the feed chute with your fingers or other utensils. Always use the food pusher provided. Do not place hands or fingers into the food chute when it is attached to the appliance.
Do not juice stone fruit unless seeds and/or stones have been removed.
Do not operate the juice extractor without the pulp and juice container in place.
Do not use the juice extractor if the juicing screw is damaged.
Do not operate the machine longer than 20 seconds before inserting ingredients.

The symbol shown indicates that this appliance should not be disposed of in the normal household waste.
It should be taken to a local authority waste collection center designated for this purpose or to a dealer providing this service.

For more information, please contact your local council office.

To protect against electric shock, do not immerse the power plug, cord, or appliance in water or any liquid.

SAVE THESE INSTRUCTIONS

Components

Sage-BJS700-Big-Squeeze-Slow-Compression-Juicer-fig-3

A. Feeding Tube & Basket
- For different sizes of produce.
B. Juicing Bowl
C. Pulp Cup
D. Drum Lid
E. Detachable Smart Cap
F. Juice Jug
G. Motor Body
H. Rotation Wiper
I. Strainer
J. Juicing Screw
K. Pusher
L. Cleaning Brush

Rating Information

220–240V~ 50/60Hz 240W

Assembly

BEFORE FIRST USE

Before using your Juicer for the first time, remove any packaging material and promotional labels.
Ensure the power is in the OFF position, the juicer is switched off at the power outlet and the power cord is unplugged.
Wash bowl and juicing tools in warm soapy water with a soft cloth. Rinse and dry thoroughly.
When first using your appliance, you may notice an odour coming from the motor. This is normal and will dissipate with use.

ASSEMBLY

Firmly insert the compression silicone into the slot below the pulp spout. The Juicer may leak if not assembled properly.
Assemble the strainer into the rotation wiper then place this assembly in to the juicing bowl ensuring the red dot on the strainer is aligned with the red dot on the juicing bowl.
Place the juicing screw into the strainer. Turn and press down on it until it clicks into place.
The juicing screw needs to be locked in place in order to close the drum lid.
Place the drum lid onto the juicing bowl aligning the dot on the drum lid with the red dot on the juicing bowl.
TIP: For easy assembly holds the drum lid by grabbing the feeding tube and turning clockwise as shown in the illustration.
Align the red dot on the drum lid with the ALIGN mark on the body and turn to the CLOSE position.
Align arrows on drum lid and motor body.
NOTE: The juicer will not operate if the down arrow on the drum lid is not completely aligned with the CLOSE mark on the body.
Place the pulp cup under the pulp spout and place the juice cup under the juice spout as shown in the illustration.

Operation

USING YOUR JUICER

After preparing the ingredients, plug the power cord into a wall outlet. Do not touch the power cord with wet hands. It may cause electrical shock, short-circuit, or fire.
Press the FORWARD button to operate.
Forward: Pulls down and slowly masticates the ingredients.
Reverse: Pushes the ingredients back up to dislodge them. The REVERSE button only works while holding down the switch.
Forward: Pulls down and slowly masticates the ingredients.
Reverse: Pushes the ingredients back up to dislodge them. The REVERSE button only works while holding down the switch.

HARD VEGETABLES & HIGH FIBRE FOODS (E.G. CARROTS, BEETROOT, & SPINACH)
Insert into the feeding tube.

Tough and fibrous ingredients: Cut to 2cm wide and 5cm long.

Fibrous leafy vegetables: (celery, kale, collard greens, etc.): Cut the stems into 5cm long and bundle up the leafy part as you insert them into the juicer.

SOFT FRUITS & VEGETABLES (E.G. APPLES, ORANGES & TOMATOES)

Insert into the feeding basket.

Soft ingredients: Cut ingredients into 1–4 pieces. Insert the prepared ingredients into the feeding basket and push down the ingredient with the basket lid to extract.

Care & Cleaning

Extract all the remaining pulp in the juicing bowl before stopping the juicer.
For easier clean-up, operate the juicer for an additional 30 seconds after the juice is extracted. Then fill the juicing bowl with water and run the juicer before opening the drum lid.
When the drum lid is stuck, press the REVERSE – OFF – FORWARD button in this order, switching back and forth 2 to 3 times to dislodge.
Then place both hands on the drum lid and firmly press down while simultaneously turning the drum lid to open.

CLEANING THE JUICER

Switch OFF and unplug the power cord from the wall outlet.
Turn the drum lid counterclockwise to open.
WARNING: When moving the appliance, do not lift it by grabbing the feeding tube. Always lift the appliance by grabbing the body or handle.
Turn the top-set counterclockwise and lift off the body.
Remove the juicing screw, strainer, and rotation wiper unit from the juicing bowl.
Clean with the provided brush.
NOTE
Immediately clean the juicer after each use.
If the remaining residue in the juicer dries up, it can make disassembling and clean-up difficult.
The excess build-up can cause poor performance in future uses. For easier disassembly, place the top set in the sink and run the water through from the top of the top set.
We do not recommend washing any parts of the juicer in the dishwasher. Washing parts in the dishwasher can cause damage to them due to prolonged exposure to harsh detergents, hot water, and pressure.
Place the juicing bowl under running water and unplug the compression silicone to clean the pulp spout.
Under running water, clean the outside of the juicing screw with a dish scrub. Use the tip of the cleaning brush to push out any residue in the crevices on the bottom of the juicing screw.
Thoroughly clean the juicing screw ensuring that the juicing screw is clean without any residue.
Thoroughly dry the bottom of the juicing screw.
After juicing ingredients with seeds, make sure to thoroughly clean the bottom crevice of the juicing screw. (If this area isn’t properly cleaned, it can cause the part to be damaged).
Clean the body with a soft damp towel and dry.
If the towel is dripping wet, make sure to squeeze out the excess liquid before using it on the juicer.

CLEANING SILICONE PARTS

Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the compression silicone and silicone ring are firmly inserted.
If the compression silicone and silicone ring are not firmly inserted, juice may leak from the bottom of the juicing bowl.

COMPRESSION SILICONE

Unplug to clean.
After cleaning, firmly insert into the slot below the pulp spout.

SILICONE RING
Remove the silicone ring from the juicing bowl to clean.
After cleaning, push in the silicone ring with the smaller surface facing down. Sage BJS700 The Big Squeeze Slow Compression Juicer - figure
20.

SMART CAP

Remove from the juice spout to clean.
After cleaning, attach the smart cap to the smart cap silicone on the juice spout.

Troubleshooting

PROBLEM	EASY SOLUTION

There is no power to
the juicer|

Check if the power cord is properly plugged in.
Check if the drum lid and the juicing bowl are properly assembled.
Check if the top-set and the body are properly assembled.

NOTE: Juicer will not operate if parts are not assembled properly.

Low juice yield|

Different ingredients hold different amounts of fluid that will yield different amounts of juice.
If the ingredients are not fresh, they may contain a reduced amount of fluid, which will yield less juice. Soak ingredients in cold water for about 30 minutes prior to juicing for the best result.
Check if the compression silicone is firmly inserted.
If the ingredient itself has low water content, it may help to soak it in water before juicing.
If juicing ingredients with small seeds, after a few servings, it may reduce the juice yield. For the best result, disassemble and wash the top set in between juicing.
If there is seed residue on the bottom of the strainer, this can affect juicer performance and the overall juice yield.

There is too much
pulp in the juice|

To reduce the fine pulp, clean the top-set frequently and extract the pulp.
Use a mesh strainer and put the juice through it to collect the unwanted pulp.
If the strainer and the screw are damaged and affect the juicer’s performance, it is recommended that the parts be replaced.
The lifetime of each part may vary depending on length and method of use and ingredients extracted.

The drum lid will not close|

Make sure the juicing screw is pushed all the way into the strainer in order for the drum lid to close properly.
If the juicing screw is not properly in position, the drum lid may not close.

Odd noise from the
juicer|

Check if the parts are assembled correctly. Try reassembling the parts and listening for the odd noise.
Do not start the juicer unless there are ingredients and/or liquid in it.
Operating the juicer without ingredients can cause damage to the screw.
If the juicer is operated without ingredients or liquid, the noise level can increase and also can lead to damage.
The friction noise from the juicing screw and the strainer will disappear when ingredients are inserted into the juicer.
If the noise occurs when ingredients are inserted into the juicer, check the size of the ingredients. Do not insert anything over 3cm in thickness.
Depending on the type of ingredients, the dimensions can be smaller.
The noise can occur if the juicer is operated on an uneven or slanted surface. Place the juicer on a horizontally flat surface when operating.

The extracted pulp is
very moist|

During the very beginning of extraction, the pulp can be moister.
Depending on the ingredient’s condition, the extracted pulp can be affected; especially when the ingredient is not fresh, the juice can be extracted with the pulp.

During operation, the juicing bowl shakes|

The juicing screw and the strainer are set up to crush and squeeze the ingredients. It is normal for the juicing screw and the strainer to vibrate.
If the ingredient contains strong fibre, the vibration from the top-set may be stronger.

During juicing, the
juicer stopped|

Check the power cord and make sure it is plugged incorrectly.
Check that all the parts are correctly assembled.
If too many ingredients are inserted at one time, this can cause the juicer to stop.
When the juicer stops because there are too many ingredients inserted in it, press the REVERSE – OFF – FORWARD button in this order, switching back and forth 2 to 3 times. The reverse setting will push the ingredients up and the forward setting will pull the ingredients down.
After using more than 30 minutes, if the juicer stops due to the overload protection, let the juicer cool for 30 minutes to 1 hour before juicing again.
If there are hard seeds within the ingredients, remove them before juicing. Hard seeds can damage the juicer.

Layers of separation in the juice|

Depending on the density of the ingredients, the extracted juice may show layers of different juices. It is different from separation due to oxidation caused by juicing with a high-speed juicer.

The drum lid is stuck|

After juicing, let the juicer operate for another 30 seconds to extract the remaining pulp.
If there is too much pulp in the top-set, this can cause the drum lid to not open. In this situation, press the REVERSE – OFF – FORWARD button in the order, switching back and forth 2 to 3 times. Then place both hands on the drum lid and firmly press down while simultaneously turning the drum lid to open.
Pour water down the feeding tube to rinse out the insides and then try opening the drum lid.

Juice dripping down
the body|

If you make sure the compression silicone is plugged incorrectly.

Is it possible to juice
ingredients with
tough fibre?|

Ingredients like celery or ginger contain long fibres that may wrap around the juicing screw and affect the juicer’s performance.
When juicing fibrous ingredients, do not collect more than 500ml of juice. After collecting this quantity or less, clean the top-set completely before juicing again.

Discolouration of the
plastic parts|

After juicing, if the juicer is not cleaned right away, the remaining pulp inside the top-set can dry up which can make disassembling and cleaning hard. This can also affect the juicer’s performance and colour.
Ingredients that are rich in carotenoids such as carrots and spinach may dye plastic parts. When the parts are dyed with carotenoids, rub vegetable oil into the dyed areas and use mild detergent to clean.
Vegetable oil should only be used during clean-up for parts that are discoloured. Do not use vegetable oil on the juicing screw or the strainer.
If vegetable oil or oil from animal fat gets on the juicing screw or the strainer, this can affect the juicer’s performance and may result in damaged parts.
The silicone pieces on the top-set can be detached to be thoroughly cleaned.

Using for purposes
other than juicing|

This juicer is designed to juice ingredients like fruits and vegetables.
Do not use the juicer for extracting vegetable oil.
Do not juice ingredients with high contents of vegetable/ animal oil.
If vegetable/animal oil gets on the juicing screw or the strainer, this can affect the performance of the juicer and could result in damaged parts.

Guarantee

2 YEAR LIMITED GUARANTEE AND 5 YEAR LIMITED MOTOR GUARANTEE

Sage Appliances guarantees this product for domestic use in specified territories for 2 years for all parts of the product and 5 years for the product’s motor from the date of purchase against defects caused by faulty workmanship and materials. During this guarantee period, Sage Appliances will repair, replace, or refund any defective product (at the sole discretion of Sage Appliances).
All legal warranty rights under applicable national legislation will be respected and will not be impaired by our guarantee. For full terms and conditions on the guarantee, as well as instructions on how to make a claim, please visit www.sageappliances.com.