WHADDA WPM456 Digital LED Strip Driver Module User Manual

: June 4, 2024
: WHADDA

Table of Contents

Introduction
Safety Instructions
General Guidelines
What is Arduino®
Product overview
Specifications
Wiring description
Example program
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WHADDA WPM456 Digital LED Strip Driver Module User Manual

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.

Thank you for choosing Whadda! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

For indoor use only.

This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.

General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
Nor Velleman nv nor its dealers can be held responsible for any damage (extraordinary, incidental or indirect) – of any nature (financial, physical…) arising from the possession, use or failure of this product.
Keep this manual for future reference.

What is Arduino®

Arduino® is an open-source prototyping platform based on easy-to-use hardware and software. Arduino® boards are able to read inputs – light-on sensor, a finger on a button or a Twitter message – and turn it into an output – activating of a motor, turning on an LED, publishing something online. You can tell your board what to do by sending a set of instructions to the microcontroller on the board. To do so, you use the Arduino programming language (based on Wiring) and the Arduino® software IDE (based on Processing). Additional shields/modules/components are required for reading a twitter message or publishing online. Surf to www.arduino.cc for more information

Product overview

The Whadda digital LED strip driver module is designed to make it easy to drive and switch 12 V LED strips with 5 V devices such as Arduino® compatible boards. The module features a step up boost converter which is designed to convert a 5 V input voltage to 12 V to drive the LED strip. The signal pin on the module can be used to switch the converter on or off when applying a HIGH or LOW input signal respectively.

Note that the module is not de

signed to work with PWM signals, the input signal must be either a steady 5 V or GND.

Specifications

Supply voltage: 5 V DC
Output voltage: 12 V DC
Output connector: 2-pin JST XH
Maximum input current: 1 A
Maximum output current: 200 mA
Weight: g
Dimensions (W x L x H): 37 x 22 x 10,2 mm

Wiring description

Pin

| Name|

Arduino® connection

---|---|---
S| Signal pin| Digital Pin (e.g. D)
VCC| Supply voltage (5 V DC)| 5V
GND| Ground| GND

Wiring description

Example program

You can download the example Arduino® program by going to the official Whadda github page: github.com/WhaddaMakers/Digital-LED-strip-driver- module

Click the “Download ZIP” link in the “Code” menu:
Unzip the downloaded file, and browse to the example_code folder. Open the example Arduino® sketch (example_code.ino) located in the folder.
Connect your Arduino compatible board, make sure the correct Board and connection port are set in the tools menu, and hit Upload