PARKER 82-03 Thermasonic Gel Warmer Instruction Manual
- June 3, 2024
- Parker
Table of Contents
PARKER 82-03 Thermasonic Gel Warmer
IMPORTANT SAFEGUARDS
This symbol when indicated on the equipment means:
CAUTION Read these operating instructions fully before use and pay
particular attention to sections containing this symbol.
Always observe the following safety precautions:
- READ THESE INSTRUCTIONS.
- CAUTION: To provide continued protection against risk of electric shock, connect to properly grounded outlets only.
- Do not immerse in water.
- Unplug from outlet when not in use and before cleaning. Allow unit to cool before cleaning the appliance.
- Do not operate any appliance with a damaged cord or plug or after a malfunction, or has been damaged in any manner. Return unit to an authorized service facility for examination, repair or adjustment.
- Do not use outdoors.
- Do not use appliance for anything other than intended use.
- The use of attachments not recommended by the manufacturer may result in fire, electric shock or injury to persons.
- SAVE THESE INSTRUCTIONS.
INCLUDED IN PACKAGE
ASSEMBLY
INSTALLATION
The Thermasonic Gel Warmer should be placed away from drafts, in an upright
position on a flat, stable surface. Do not lay the unit flat on any side. The
unit may also be wall-mounted. See section 3.2 for wall mounting instructions.
Plug female end of power cord into IEC320/C14 receptacle (see Figure 1) and
male end into an appropriate electrical outlet matching the voltage listed on
the electrical information label on the back of the Gel Warmer. NOTE: UK
power cord with a BS-1363 plug (Part #: UKCORD) is available in the United
Kingdom, as an accessory from your distributor.
WALL-MOUNTING
The Thermasonic Gel Warmer can be mounted on a wall with the use of the
supplied screws and wall anchors. Follow these steps to wall mount.
-
Once wall-mount location has been identified, make two marks on the wall 4 inches (10.16 cm) apart. When making your marks, use a level to assure the Gel Warmer will appear straight when mounted.
-
If mounting into wood, install screws and allow 0.1” (2.5mm) clearance between the wall and the screw head. If mounting into drywall, the use of wall anchors is necessary.
CAUTION: Never drill or install screws in a wall with wires or plumbing running through it. -
Carefully position the Gel Warmer so the large round wells (see Figure 2) on the back of the unit will pass over the screw heads.
-
Press the Gel Warmer against the wall and slide downward, trapping the screw head in the grooves just above the wells.
OPERATION
CONTROLS AND INDICATOR LAMPS
When switched to the ON position, the power ON/OFF switch will illuminate (see
Figure 3) and remain lit, indicating the unit is operational.
SETTING ThE OPERATING TEMPERATURE
Models 82-03 and 82-03-20
CAUTION: Temperature can vary. Always test a small quantity of gel before applying. Do not use HIGH setting on infants, the elderly or patients with very sensitive skin.
When powered on for the first time, the LED corresponding with MED will begin
to flash (see Figure 4), indicating the Gel Warmer is functioning and is
warming to MEDIUM (factory setting). When removed from a power source, the Gel
Warmer will remember the last temperature setting and maintain that setting
when powered on again.
You may switch between the LOW, MEDIUM, and HIGH settings by pressing the
thermometer button below the bank of LEDs (see Figure
5).Once the unit reaches the set temperature, the
LED will stop flashing and remain illuminated. Should the temperature drop
below the acceptable temperature range, the LED will again flash until the
unit returns to the correct temperature.
Models 83-03 and 83-03-20
CAUTION: Temperature can vary. Always test a small quantity of gel before
applying.
When powered on for the first time, the digital display will indicate the
current temperature and will begin warming to the factory-set temperature of
102° F (39° C) (see Figure 6).
To adjust the temperature, press the arrow button with + symbol to increase
temperature, or press the arrow button with – symbol to decrease temperature
(see Figure 7). Each time one of the arrow buttons is pressed, it will
increase or decrease the temperature setting by one degree and flash the newly
set temperature for five seconds. The unit will then return to displaying the
current temperature.
Warm and comfortable is now even better.
To switch between Fahrenheit or Celsius on the temperature display, press both
the + arrow button and – arrow button simultaneously. When removed from a
power source, the Gel Warmer will remember the last temperature setting used
and maintain that setting when the unit is powered on again.
OPERATING ThE GEL WARMER
Allow approximately two hours for a full bottle of gel to reach proper
temperature. Leaving the cover closed at all times will help retain heat. Your
Thermasonic Gel Warmer is designed for continuous operation, and it is not
necessary to disconnect the warmer when not in use.
NOTE: Since gels are aqueous, some condensation may appear in the
applicator cap of the gel bottle. Use of the Thermasonic Gel Warmer will not
affect the performance or v iscosity of any Parker ultrasound gel.
ERROR CODES
The Thermasonic Gel Warmer contains a temperature sensor to consistently
monitor function and a Microtemp® thermal cutoff to protect against
overheating.
Models 82-03 and 82-03-20
If the temperature sensor is not operating, all the LEDs will blink once every
five seconds. If a short circuit occurs, the LEDs will blink twice every five
seconds. In either circumstance, the heater will not operate.
Models 83-03 and 83-03-20
If the temperature sensor is not operating at all, the digital display will
indicate “E1”. If a short circuit occurs, the digital display will indicate
“E2”. In either circumstance, the heater will not operate.
TECHNICAL SPECIFICATIONS
This equipment is intended for indoor use and will meet its performance figures within the ambient temperature range of 68˚F (20˚C) to 95˚F (35˚C), with maximum relative humidity of 80% (non-condensing). Installation Category II (transient voltages). Pollution Degree 2, in accordance with IEC 664. Suitable for operation at altitudes of up to 6,500 feet.
Specifications:
-
Supply Voltage Range:
120V~ +/- 10%, 50/60 Hz
230V~ +/- 10%, 50/60 Hz (CE version) -
Power Rating:
Model 82-03, 83-03: 31W, 0.26A
Model 83-03-20, 83-03-20: 31W, 0.15A
MAINTENANCE AND SERVICE
No routine maintenance is required and there are no user-serviceable parts.
CLEANING
Disconnect the Gel Warmer from the electrical outlet prior to cleaning. The
Gel Warmer may be cleaned by using a soft, damp cloth and a mild detergent or
hospital grade disinfectant, such as ProteX™ ULTRA Wipes. Do not allow the
electronic controls to get wet. Do not use an abrasive cleaner or isopropyl
alcohol to clean the Gel Warmer. Do not submerge or immerse the
Gel Warmer in water.
WARRANTY
All Thermasonic Gel Warmers have a two-year Limited Warranty from date of
purchase. DO NOT attempt to service your Thermasonic Gel Warmer. Any evidence
of the unit being disassembled, tampered with, or misused will void the
warranty. Contact Parker Laboratories, Inc. with any service or warranty
questions through email: parker@parkerlabs.com
NOTE: Product must be registered online at time of purchase.
Please register your model at: www.parkerlabs.com/register/thermasonic
FREQUENTLY ASKED QUESTIONS
This instruction manual contains the answers to most questions about the use and care of your Thermasonic Gel Warmer. You may also find answers to some of the most frequently asked questions by visiting: www.parkerlabs.com/thermasonic
Declaration of Conformity
Certification: Parker Laboratories, Inc. certifies this instrument was
inspected and tested thoroughly and met its published specifications when
shipped.
© 2017 Parker Laboratories, Inc. All Rights Reserved.
® Thermasonic is a registered trademark of Parker Laboratories, Inc. ™ Protex
ULTRA is a registered trademark of Parker Laboratories, Inc. ® Microtemp is a
registered trademark of Emerson Electric Co.
References
- ParkerLabs - Parker Laboratories Inc. : Ultrasound and Electromedical Gels, Creams, Warmers , Cleaners and more
- Thermasonic® Gel Warmer - ParkerLabs
- Thermasonic® Gel Warmer - ParkerLabs
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>