exway RP1 Remote Control Handle User Manual

exway RP1 Remote Control Handle

Product Information

Specifications:

• Compliance: FCC Part 15
• RF Exposure: General RF exposure requirement met
• Usage: Portable exposure condition without restriction

Product Usage Instructions

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes and Modifications:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF Exposure:
The device has been evaluated to meet general RF exposure requirement. It can be used in portable exposure conditions without any restrictions.

Frequently Asked Questions (FAQ)

• Can this device be used in areas with high interference?
  The device is designed to accept interference and can be used in various environments, including those with interference, as long as it does not cause harmful interference.

• Are there any restrictions on where this device can be used?
  The device can be used in portable exposure conditions without any restrictions, ensuring flexibility in its usage.

Charging port

Please charge Flex Paragon with original charger only.
(After the skateboard is fully charged, the charger indicator light turns green. The cover must be closed after charging to ensure waterproof performance.)

External discharge

Short press once to display the battery level; long press for 3 seconds to turn on/off the USB-C external discharge function, 60WMax.

Power button

The power button is located on the ESC at the back of the skateboard. By default, the skateboard in standby mode will turn off after 24 hours. (Can be modified in settings.)

Skateboard indicator light operations and status

• Power on
  Press the power button for 1 time

• Power off
  Long press the power button for 3 seconds

• Pair
  Press and hold the power button for 8 seconds (When the skateboard is turned off)

• Green light always on
  Normal working status

• Green light flashes slowly
  Upgrading

• Motor matching
  After turn in on the skateboard, s ? art press the button for 5 times

• Red light always on
  The skateboard is not connected to the remote control

• Red light flashes slowly
  Charging

• Red and green lights flash alternately
  Pairing mode

Battery replacement

1. Press the buckle to unplug the power connector.

2. Open the two locks on the left and right respectively, push back to remove the battery pack.

3. Lift the battery connector and push the battery in. Connect the power connector and make sure both locks are well fasten.

Remote control

User interface

Operation Guides

Gear button/direction button operation instructions

• Power On/Off
  Press and hold the gear button for 2 second

• Accelerate/Brake
  Spin forward to accelerate Pull back to brake

• Switch Directions
  Slide to change the board’s riding direction (when Speed<Skm/h)

• Switch Gears
  Short press once to select the next speed mode

• Turbo Mode
  Short press for 3 times

• Cruise control
  Hold the throttle still+ short press twice to activate cruise control (Speed is 5~25km/h)

  • Menu callout, tank mode (4WD), parking function only take effect when speed is less than 5km/h, but better set them when the skateboard is totally stationary.
  • CRUISE Control: After this function is turned on, if the speed of the board changes greater than 5km/h or the throttle wheel is operated, cruise control will deactivate.
  • Shift Lock: This function is turned off by default and gear can be shifted only when the skateboard is stationary.This function can be unlocked from the setting menu. Once it’s turned on, the gear can be switched as long the remote roller is centered when the skateboard is rolling.

Light Button/ATIP Button Operation Instructions

• Turn on/off the ambient light
  Short press the button 1 time

• Switch ambient light animation
  Short press the button 2 times

• Turn on/ off the lighting lamp
  Short press the button 3 times

• Left/right turn signal
  Tilt the remote control left/right+ short press unlock button 2 times to activate it

• Operation mode/setting menu switching
  Long press the button for 2 seconds (Speed < 5km/h)

• N Gear
  No input of throttle wheel for a period of 5 seconds will automatically activate neutral gear mode. Push ATIP button to activate previously selected speed mode

• Parking mode
  Pull the throttle wheel to the braking position while the board is stationary+ short press the ATIP button 3 times

• Remove parking mode
  In the parking mode, press the ATIP button one time

  • Atlas Pro, Flex Pro and other devices do not have lighting and ambient lighting functions, so turning on the functions will have no effect.
  • Turn signal: In the operation mode,twist your wrist and press the ATIP button twice to enter the turn signal mode and it automatically exits after 5 seconds.
  • ATIP:After the anti-accidental touch function is turned on,the brake and turn signal functions are available, but the throttle acceleration is not available.

Touch screen instructions

Speed mode/power mode switching
Double-tap the center of the screen, you can switch speed mode/power mode.

Enter the setting interface
Swipe up from the bottom/Swipe down from the top. Click the return button to Exit and return back.

Introduction to setting interface

Lighting Parameter Settings
Swipe right from the left edge/swipe left from the right edge to enter the settings interface. Click the return button to exit the setting.

Introduction to setting interface

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.

1. This device may not cause harmful interference.and
2. This device must accept interference received,including interference that may cause undesired operation.

Safety Instructions & Disclaimer

1. Using an electric skateboard has the same potential risks as other sports and may cause injury. even death.
2. You must read the instruction manual before use and wear protective gear.
3. The belt will wear out under normal use, please refer to Exway related tutorial videos for correct replacement Damaged belt.
4. Please follow local traffic laws and regulations and use it safely within the permitted scope.
5. Children under 14 years old, disabled people, pregnant women, the elderly, etc., as well as those with mental disorders, diseases, It is prohibited for use by people with impairments in normal body movement.
6. Skateboard, remote control, App will be continuously updated, and there may be differences between the manual and the final version of the firmware . For details, please refer to the official website for the latest version.
7. If not used for a long time, please charge and discharge the skateboard every 30 days to have around 30-75% battery left for storage to ensure battery life.
8. After replacing the battery, please ensure that the plug and fixing buckle are installed in place, otherwise it may affect the power supply and Waterproof properties.
9. The product has certain waterproof performance, but failure caused by water ingress is not covered by the warranty. Please pay attention to waterproofing.
10. Please cover the rubber plug after using the external discharge function to ensure waterproof performance.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>