exway W1R Wave Hub User Manual

away W1R Wave Hub

overview

1. Front of the Board Top Speed： 23mph / 38kph
2. Grip Tape Hill Climbing： Up to 25% Grade
3. Kicktail Range： 15miles / 24km
4. Truck  Weight： Weight: Riot 7.3kg / Hub 6.9kg
5. Torque: Riot 4.3Nm x 2/Hub 3.8Nmx2
6. Charging Port  Max. Power: 1000WX 2
7. Battery  Rated Motor Power: 430Wx 2
8. Status Indicator/Power Button    Max Amperage: 4A
9. Taillight    Input Voltage: 100-240VAC,50/ 60Hz
10. Front light Auxiliary Port      Battery Capacity: 216Wh
11. Charging Time: 3.5 hours (1h30mins with the fast charger)
12. Trucks: Exway Trist 45° 7
13. 1Motor Controller (ESC)
14. Brushless Motors    Recommended Age Range: 16-50 Years
15. Rear Drive Wheel  Max Load: 100kg/ 220lbs
16. Tail Puc    Waterproof Level: IP53
17. Brakes: Regenerative Braking

Battery Swap

• Battery Installation: Align both the ports from the battery and deck. Slide the battery into place, ensuring that it’s securely mounted. (Otherwise, it may fall out while riding and cause danger or injury)
• Battery Removal: Press and hold down the battery release button, meanwhile slide the battery towards the rear truck to lift it away from the board.

Install the front lights

Install the lights on the front of the board and ensure that the four screws are fully tightened. Turn on the board and then double tap the multi-button on the remote to switch on the lights.

Operations & The state of the indicator lights

CAUTION:

1. When the skateboard battery has 59% left, the power output will be cut off to better protect the battery. (In free mode, both the power output and brakes will be restricted)
2. Connect the charger to the power button on the board before plugging into the wall outlet. (Only use an original Exway Wave charger)

BY THE WAY:

1. The board will charge for around 3.5h with the standard charger. The indicator on the charger will turn green when the battery is full.
2. This version of the user manual may not be updated, check out the Exway App or www.exwayboard.com to read the most up-to-date version.

14 Acceleration (roll the throttle forward)
15 Throttle Wheel
16 Breaking (roll the throttle back)
17 Multi-Button
18 OLED screen

Remote Control Operation

Pairing Remote to Board

• Choose the first option “Re-Pair” by tapping on the Multi- Button.
• Choose your board and click “YES”.

Remote Control Calibration

• Push the roller forward to the bottom without letting go, and press the multi-button to Confirm.
• Calibrate the neutral position, release the roller to make it free, and press the multi-button to confirm.
• Press multi-button to confirm when calibration is completed and the calibration interface is automatically exited.

WARNINGS

• LOW TEMPERATURE
  Temperature is below 0’C (Caution frost).

• BATTERY TEMPERATURE WARNING
  Battery temperature is over 55″C

• ESC HIGH-TEMPERATURE WARNING
  ESC OVERHEATING WARNING
  SC temperature is over 120’C.
  Stop using your board immediately to allow it to cool)

• MOTOR HIGH-TEMPERATURE WARNING
  Motor temperature is over 100’C.

• MOTOR OVERHEATING WARNING
  Motor temperature is over 120″C. (Stop using your board
  immediately allow it to cool)

• MOTOR BREAKDOWN
  Motor Seizing

• HIGH VOLTAGE (1)
  Voltage is too high

• HIGH VOLTAGE (11)
  Voltage is too high (Danger risk! Discharge it Before use)

• LOW TEMPERATURE
  Low Charge temperature

• BATTERY OVERHEAT
  Battery is overheating while charging.

• REMOTE DISCONNECTED
  Remote is not connected to board.

• BMS ERROR
  BMS error or connection issue at battery communication port.

In the box

1. O Exway Wave
2. Remote
3. Standard charger
4. Remote Charging Cable
5. Skate Tool
6. User Manual
7. 2.0 mm LWrench 2.5 mm L Wrench 5.0mm wrench

Warnings & Safety Information

1. . Whenever you ride an Exway board, you risk death or serious injury from loss of control, collisions, and falls. To ride safely, you must read and follow all warnings and instructions in this manual.
2. Always wear a helmet when riding. Never ride in water, wet surfaces, in the rain, slippery or uneven surfaces, steep hills, traffic, cracks, train tracks, gravel, rocks, or any obstacles that could cause a loss of traction. Avoid night riding, areas with poor visibility, and narrow spaces.
3.  Do not ride an Exway board in environments, on inclines, or at speeds where you would not be safely in control of an unpowered skateboard  In the event of wireless interference or battery fault, you may need torely on skating techniques like foot-braking or sliding to stop. The Exway electric skateboard is not a toy and is not intended for children under 16.
4.  Please ride responsibly and respect those around you. How you ride will determine how people view this new mode of transportation.
5.  The version of the user manual may not be up to date, check out the Exway App or www.exwayboard.com to read the most up-to-date version.
6. If you do not use your board for long periods of time, please discharge and recharge your board every 30 days.
7. Scan QR code to download the App and get the most up-to-date version of the user manual.
8. Do not store the board at 100% battery charge for extended periods of time, doing so will permanently damage the battery. Maintain around 60% charge when storing for a long time and do not allow battery charge to go below 40%.

• Scan the QR code to download the APP to get the electronic version of the manual

FCC Caution

•  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirements. The device
  can be used in portable exposure conditions without restriction.

References

• Exwayboard - The Most Advanced, Smartest Electric Skateboard American Express Diners Club Discover JCB Maestro Mastercard PayPal Visa

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>