TACO DL-ECB10-US32D, Satin Stainless Steel Trans Atlantic Instruction Manual

June 5, 2024
TACO

TACO DL-ECB10-US32D, Satin Stainless Steel Trans Atlantic

INSTRUCTIONS FOR INSTALLATION OF ENTRANCE LOCKS IN NEW DOORS OR THE REPLACEMENT OF EXISTING LOCKS

TOOLS REQUIRED FOR NEW INSTALLATION’

  • 1 phillips head screwdriver
  • 1 2-1/8″ (54mm) hole saw
  • 1 1″ (25.4mm) drill bit
  • 1 chisel

FOLLOW ALL STEPS FOR REMODELING OR NEW CONSTRUCTION. FOLLOW STEPS 3C,4C,5,6,7,8,9 and 10 FOR DO-IT-YOURSELF REPLACEMENT AFTER REMOVAL OF EXISTING LOCK.

REPLACING EXISTING LOCKS

Before beginning, measure from center of lock to door edge in order to check length of backset on existing lock. The backset length of new lock is stated clearly on front of package. If backset size is the same, you’ll have to replace lock with proper size backset.

TOOLS REQUIRED FOR REPLACEMENT INSTALLATION:
1 phillips head screwdriver ILLUSTRATIONS ARE SHOWN WITH ENTRANCE MODELS. INSTALLATION IS SAME FOR PRIVACY AND PASSAGE MODELS AS WELL.

TACO-DL-ECB10-US32D-Satin-Stainless-Steel-Trans-
Atlantic-1

INSTALLATION INSTRUCTIONS

MARK DOOR
Start approximately 36″ (914mm) from floor. Fold and apply template to edge of door and mark center of door edge as indicated on template. Mark center hole on door face through guide on template.

( NOTE : Backset on door face must be same as backset of lock.)

DRILL HOLES
Drill 2-1/8″ (54mm) hole through door face as marked for lockset. It is recommended that holes be drilled from both sides to prevent splitting. Drill 1″ (25.4 mm) hole in center of door edge for latch. 1″ (25.4mm)

INSTALL LATCH

  1. Insert latch in hole keeping it parallel to face of door. Mark  outline and remove latch.
  2. Chisel 5/32″ (4mm) deep or until latch face is flush with door edge. TACO-DL-ECB10-US32D-Satin-Stainless-Steel-Trans-Atlantic-5
  3. Insert latch and tighten screws.
    ( NOTE : Latchbolt bevel  must face to closing direction.)

INSTALL STRIKE

  1. Close door until latchbolt touches jamb to locate strike in jamb and center line of strike. Open door and extend line from mark to door stop. Measure one half of door thickness from door stop and vertically mark drill point center for strike.

  2. Drill 1″ (25.4mm) hole 1/2″ (12.7mm) deep in door jamb on drill point for strike.
    CAUTION : To ensure proper lockset function. Hole in jamb must be drilled a full 1/2″ (12.7mm) deep.

  3. Cut out jamb 1/16″ (1.5mm) deep for strike. Tighten screws.  Guardbolt stops against strike, as illustrated, preventing forcing when door is closed. Adjustable tang on strike permits bending in or out to  eliminate too loose fit between door and door stop.

REMOVE INSIDE TRIM
Depress spring attached to inside rose. Insert nail end of wrench into slot to remove inside rose plate.

ADJUST OUTSIDE ROSE
Adjust lock to fit door thickness by rotating outside rose. Lock will fit all doors 1-3/8″ to 1-3/4″ (35mm~45mm) thick.

INSTALL LOCK
Latch unit must be in place before installing lock. Be sure lock housing engages with latch prongs and retractor interlocks with latch tail.

INSTALL INSIDE ROSE

FOR WOODEN DOOR
Tighten machine screws securely to install mounting plate. Press rose onto mounting plate. Be sure to fit rose in recess of mounting plate.

FOR METAL DOOR
MOTE: Make sure that mounting plate fit horizontally into slots notched in door.

TACO-DL-ECB10-US32D-Satin-Stainless-Steel-Trans-
Atlantic-13

IMPORTANT-
Align lug on knob with narrow slot on side of spindle and push knob all the way in until knob catch clicks into slot on knob. Otherwise knob will jamb on shaft.

RIGHT KEY HOLE POSITION

Upon installation of the lock, it may happen that key hole faces upward or downward as shown in the following drawing. It is advisable to correct all key hole to be facing downward.

IN ORDER TO ADJUST THE ABNORMAL STATE OF THE KEY HOLE FACING UPWARD, THE KNOB MUST BE PULLED OUT AND INSTALLED AGAIN. THE METHOD OF INSTALLATION IS DESCRIBED AS BELOW D.

  1. First turn the knob clockwise until the knob catch appears in the small hole
  2. With the other hand, turn the key counterclockwise within the limit of 30°~90°
  3. Using a small nail to press the knob catch and pull the knob out.
  4. Install again according to the correct direction.

TEMPLATE

TACO-DL-ECB10-US32D-Satin-Stainless-Steel-Trans-
Atlantic-20

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals