tp-link Festa F41-Outdoor Omada Indoor Outdoor Access Point Instructions

: September 26, 2024
: tp-link

Table of Contents

Festa F41-Outdoor Omada Indoor Outdoor Access Point
Specifications:
Product Usage Instructions:
Regulatory Compliance:
Installation:
Operation:
Maintenance:
- FAQ:
Q: What should I do if I encounter radio interference?
Q: Can I use the access point with other antennas or
Q: How can I ensure RF exposure compliance?

Festa F41-Outdoor Omada Indoor Outdoor Access Point

“`html

Specifications:

Product Name: Omada Indoor/Outdoor Access Point
Model Numbers: Festa F41-Outdoor, Festa F52-Outdoor, Festa
F61-Outdoor, Festa F65-Outdoor
Operating Frequency:
- For Festa F41-Outdoor: 2412MHz-2472MHz (20dBm)
- For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor:
- 2412MHz-2472MHz (20dBm)
- 5150MHz-5250MHz (23dBm)
- 5250MHz-5350MHz (23dBm)
- 5470MHz-5725MHz (30dBm)

Product Usage Instructions:

Regulatory Compliance:

Ensure compliance with FCC regulations regarding harmful
interference and RF radiation exposure limits.

Installation:

Mount the Omada Indoor/Outdoor Access Point in a suitable
location.
Connect the I.T.E. Power Supply to the access point according
to the model number.
Ensure a separation distance of at least 20cm between the
antennas and all persons.

Operation:

Power on the access point and configure the settings as needed
for your network.

Maintenance:

Regularly check for any physical damage or signs of
interference. Keep the access point clean and free from
obstruction.

FAQ:

Q: What should I do if I encounter radio interference?

A: If radio interference occurs, consider repositioning the
access point or taking adequate measures as required.

Q: Can I use the access point with other antennas or

transmitters?

A: To comply with FCC regulations, do not co-locate or operate
the access point with any other antenna or transmitter.

Q: How can I ensure RF exposure compliance?

A: Maintain a separation distance of at least 20cm between the
antennas of the access point and all persons during operation.

“`

Regulatory Compliance
Festa AP_Indoor/Outdoor
© 2024 TP-Link 1910013663 REV1.0.0

For Class B AP with adapter:
FCC Compliance Information Statement

Product Name: Omada Indoor/Outdoor Access Point Model Number: Festa F41-Outdoor / Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor

Component Name

Model

I.T.E. Power Supply

T240025-2-POE (for Festa F41-Outdoor) T240050-2-POE (for Festa F52-Outdoor) T480050-2-POE (for Festa F61-Outdoor) T480038-2-POE (for Festa F65-Outdoor)

Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.”
Product Name: I.T.E. Power Supply
Model Number: T240025-2-POE / T240050-2-POE / T480050-2-POE / T480038-2-POE
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.

· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2024-05-06
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
OPERATING FREQUENCY (the maximum transmitted power)
For Festa F41-Outdoor: 2412MHz–2472MHz(20dBm) For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor: 2412MHz–2472MHz(20dBm) 5150MHz–5250MHz(23dBm) 5250MHz–5350MHz(23dBm) 5470MHz–5725MHz(30dBm)
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/ce.

RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20cm from your body.
National Restrictions
For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor: Frequency band: 5150 – 5250 MHz: Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band. Frequency band: 5250 – 5350 MHz: Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted. Frequency band: 5470 – 5725 MHz: Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.
UKCA Mark
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www .tp-link.com/support/ukca
National Restrictions
For Festa F52-Outdoor / Festa F61-Outdoor / Festa F65-Outdoor: Attention: In Great Britain, the operation in the frequency range 5150MHz – 5350MHz is only permitted indoors.

UK

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

For Festa F52-Outdoor:
This radio transmitter (IC: 31152-F52OD / Model: Festa F52-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list below, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 31152-F52OD / Model: Festa F52-Outdoor) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste ci-dessous et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

Antenna

Two 2.4GHz 3dBi external omnidirectional antennas Two 5GHz 5dBi external omnidirectional antennas

Caution
For Festa F52-Outdoor:

The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point- to-point operation as appropriate; and

For Festa F61-Outdoor / Festa F65-Outdoor: 1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong. 2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit; DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 54705600MHz, and 5650-5725MHz.
Avertissement
Pour Festa F52-Outdoor: 1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 3) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation point à point et non point à point, selon le cas. Pour Festa F61-Outdoor / Festa F65-Outdoor: 1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 2) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limitation P.I.R.E.; Les produits utilisant la technique d’atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements
.
NCC Notice & BSMI Notice
Festa F61-Outdoor / Festa F65-Outdoor Festa F52-Outdoor
. . 40

Pb

Cd

Hg

CrVI

PBB

PBDE

PCB

—

1. “0.1 wt %” “0.01 wt %” . 2.””. 3.”–” .

, .

Safety Information
Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
Adapter should be used indoors where the ambient temperature is lower than or equal to 40 . Outdoor products are powered through the adapter’s output line.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed
Adapter shall be installed near the equipment and shall be easily accessible.
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us.
Plug the adapter into the wall outlets with earthing connection through the power supply cord.
Operating Temperature: -30 70 (-22 158 )
This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product

is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product label
Note: The Equipment marking is at the bottom of the device. Symbols may vary from products. Symbol Explanation Class II equipment
Class II equipment with functional earthing Alternating current Direct current Polarity of d.c. power connector For indoor use only
Dangerous voltage
Caution, risk of electric shock
Energy efficiency Marking
Protective earth
Earth
Frame or chassis
Functional earthing
Caution, hot surface

Caution
Operator’s manual
Stand-by
“ON”/”OFF” (push-push)
Fuse
Fuse is used in neutral N RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Caution, avoid listening at high volume levels for long periods

Disconnection, all power plugs

m

Switch of mini-gap construction

Switch of micro-gap construction (for US version)

µ

Switch of micro-gap / micro-disconnection construction (for other

versions except US)

Switch without contact gap (Semiconductor switching device)

Mounting Requirements
For safety, we recommend you to use the original screws in the package when mounting. The following are alternatives to mount the device on the wall: · Use 2 screws which comply with ANSI B1.1 4#, (5#), 6# standard and are longer than 7mm.