FEIT ELECTRIC S5.5WPK Lumens Adjustable White Motion Mini User Guide

FEIT ELECTRIC S5.5WPK Lumens Adjustable White Motion Mini

READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS

We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this product. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric.

Safety Information

For your safety, always remember to:

• Follow all safeguards stated in the manual, in addition to normal safety precautions in working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.
• WARNING: RISK OF SHOCK: House electric current can cause painful shock or serious injury unless handled properly. For your safety, always remember to:
  • Turn OFF the power supply at the fuse or circuit breaker box before you install the fixture.
  • Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
  • Double-check all connections to be sure they are tight and correct.
  • Wear rubber shoes and work on a sturdy ladder.
• This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed by local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
• WARNING: RISK OF CUTS: Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.
• Account for small parts and destroy packaging material, as these may be hazardous to children.

Supplier’s Declaration of Conformity:

47 CFR § 2.1077 Compliance Information Responsible Party:

• Feit Electric Company
  4901 Gregg Road, Pico Rivera, CA 90660, USA

• Unique Identifier:
  S5.5WPK840DDBZ

Product Specifications

120 VAC, 60Hz, 23 Watts Not for use with dimmers Suitable for wet locations.

• WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed by the owner’s manual, current electrical codes, and/or the current National Electric Code (NEC). Properly ground electrical enclosure. Use only UL or IEC-approved wire for input/output connections.
• CAUTION: This product must be installed under the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radionic technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Care & Maintenance

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from the date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact- us, or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | 800-543-3348 | FAX 562-908-6360 | www.feit.com.

Pre-Installation

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)

NOTE: Hardware not shown to actual size.

HARDWARE INCLUDED

Troubleshooting

Installation

1. Turning Off the Power
   Turn the power OFF at the wall switch and fusebox or the circuit breaker.

2. Removing Lens
   Remove the Fixture Lens (CC) from the Wall Pack Fixture (AA) by unscrewing the four Lens Screws (EE).

3. Removing Reflector
   Remove the Reflector (BB) from the Wall Pack Fixture (AA) by unscrewing the two Reflector Screws (DD).

4. Opening the Knockouts
   Use a screwdriver and hammer (not provided) to knock out the screw holes on the Wall Pack Fixture (AA) according to the J-box being used.

5. Connecting the Power Supply Wires
   Using Wire Connectors (GG), connect the 3 wires coming from the Wall Pack Fixture (AA) to the Junction Box Wires: Black – Line Voltage, White – Neutral, Yellow-Green or Green – Ground

6. Affixing Fixture to J-Box
   Feed the junction box wires and fixture wires into the Junction Box. Mount the Wall Pack Fixture (AA) to the J-Box using the two J-Box Screws (FF) through the knockout screw holes.

7. Replacing Reflector
   Re-assemble the Reflector (BB) to the Wall Pack Fixture (AA) by screwing in the two Reflector Screws (DD).

8. Replacing Lens
   Re-assemble the Fixture Lens (CC) to the Wall Pack Fixture (AA) by screwing in the four Lens Screws (EE).

9. Bypassing Dusk-to-Dawn Sensor
   (Optional) To bypass the Dusk-To-Dawn Sensor to operate the Fixture by wall switch only, simply place the Dusk-To-Dawn Sensor Cover (HH) over the Sensor.

10. Turning the Power On
    Turn the power ON at the wall switch, circuit breaker, or fuse box.

11. Applying Sealant
    Once the fixture is tightly secured to J-Box, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.

FEIT ELECTRIC COMPANY | PICO RIVERA, CA | 800-543-3348 | FAX 562-908-6360 | www.feit.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>