NITHO MLT-NEXS-W Nexus Wireless Controller User Guide
- September 24, 2024
- NiTHO
Table of Contents
- MLT-NEXS-W Nexus Wireless Controller
- Product Information
- Specifications
- Product Usage Instructions
- Before Using Nexus
- Wired Connection Setup
- Reset Function
- PC Connection
- Wireless Connection Setup
- Adjusting Turbo Speed
- Calibrating Axis Sensor
- RGB Light Effect Setup
- Vibration Intensity Adjustment
- Q: How do I know when the battery is low?
- Q: How to adjust RGB light brightness?
MLT-NEXS-W Nexus Wireless Controller
Product Information
Specifications
Model: MLT-NEXS-W
Features:
-
Buttons: T(Turbo), HOME, A, B, X, Y, L, ZL, R, ZR, L3, R3, ^,
v, Screenshot, Select -
Wireless Range: Up to 6 meters
Product Usage Instructions
Before Using Nexus
Before connecting the Nexus controller for the first time:
-
Fully charge the battery using the supplied USB cable and a USB
port. -
LED indicators will show charging status.
-
Note: Low battery will prompt rapid LED blinking and sleep
mode.
Wired Connection Setup
-
Connect the USB data cable to the Switch console’s USB port
while the controller is off. -
The controller will reconnect wirelessly after unplugging the
USB cable.
Reset Function
Note: Open the wired controller connection option in Console
Settings.
PC Connection
-
Connect the USB data cable to the Nexus controller and the
PC. -
Switch between X-Input and D-Input modes using button
combinations.
Wireless Connection Setup
-
Turn on Bluetooth function and pair the controller with the
console. -
LED indicators will confirm successful pairing.
Adjusting Turbo Speed
Customize Turbo mode settings using specific button
combinations.
Calibrating Axis Sensor
Recalibrate sensor if needed using console settings or specific
button combinations.
RGB Light Effect Setup
Adjust RGB light brightness in any mode using button
combinations.
Vibration Intensity Adjustment
- Adjust vibration intensity levels using specific button
combinations.
Frequently Asked Questions (FAQ)
Q: How do I know when the battery is low?
A: The central LEDs will blink rapidly, indicating low battery
and entering sleep mode.
Q: How to adjust RGB light brightness?
A: Press LIGHT + UP/DOWN buttons to increase or decrease RGB
light brightness.
EN
NEXUS
WIRELESS CONTROLLER
QUICK START GUIDE
Model: MLT-NEXS-W
SPECIFICATIONS
THANK YOU FOR BUYING NITHO NEXUS WE WOULD LIKE TO INTRODUCE ITS
SPECIFICATIONS:
A. Full compatibility with Switch®, PC, iOS® and Android®. B. It’s equipped
with the latest motion sensor technology. C. The built-in six-axis gyroscope
and six-axis accelerator can detect an omnidirectional dynamic information
including Roll, Pitch and Yaw. D. Multiple selectable RGB light effects in
eight different colours. E. High performance Hall effect triggers. F. Three
turbo selectable speed adjustments. G. Four motor vibration intensity
adjustment with memory function. H. The LED central lights displays the
charging status and battery level. I. Automatic controller wake-up and device
reconnection.
FEATURES
BUTTONS LIST T(Turbo), HOME, A, B, X, Y, L, ZL, R, ZR, L3, R3, ^, v, <,>,
Screenshot, Select
COMPATIBILITY Supports Switch® console, Android®, iOS®(above 13.0) and
PC(Windows® 10 and above) D-Input protocol if wireless and D-Input + X-Input
protocols if wired.
CONNECTION NEXUS keeps connected up to 6 metres away from the main device.
NOTE BEFORE USING NEXUS
Before connecting NEXUS controller for the first time, fully charge the
battery. To recharge the battery, plug the supplied USB cable into the
controller and a USB port. In controller shutdown state, the LED1-LED4 mode
indicator blinks slowly while charging, and turns off when charging is
complete. Note: When the controller’s battery is low, the central LEDs will
blink rapidly and it will enter in sleep mode
WIRED CONNECTION SETUP
SWITCH®
1.While the controller is off, directly connect the USB data cable to the Switch console’s USB port.
2.Controller will automatically connect back to the console
through Bluetooth wireless mode after unplug the USB
cable.
RESET FUNCTION
Note: need to open the wired controller connection option in the Console Setting
PC
Connect the USB data cable to NEXUS controller and the PC.
Enter X-Input mode(default), then the LED1+LED4 is light on
Press and hold the “-” and “+” button for 3 seconds to enter the D-Input mode, LED2+LED3 is light on.
WIRELESS CONNECTION SETUP
CONSOLE 1.Turn on Bluetooth function
1). Enable Bluetooth on Switch® Console. 2). Turn on the Switch® console and
go to the “System Settings” Menu, then click “Airplane Mode” option 3
. Select “Controller Connection (Bluetooth)” option to turn on Bluetooth
function. 2. Pairing Controller 1). Click the controller menu button on the
console to matching controller: “Controllers” > “change Grip/Order” 2). Press
“Y” and “HOME” buttons or hold the “Pairing button” for 3 seconds to enter
Bluetooth pairing mode. 3). Once paired successfully, LED1-LED4 will flash
rapidly.
Note Synchronizing states or pairing with the Console: LED1-LED4 light
flashing quickly
PC, IOS® & ANDROID® On standard Android® Mode Press “A” + “HOME” button to
paring mode, LED2+LED3 is flashing quickly Click “GamePad” devices name on
your Android device to pair, LED2+LED3 light will stop to blink after
successfully pairing. On Bluetooth IOS®/PC and Android® Mode Press “X” +
“HOME” button, LED1+LED4 is flashing quickly Click the “Xbox Wireless
Controller” device name on your Android® devices , LED1+LED4 light is steady
on after pairing successful. (In Bluetooth iOS®/PC X-Input mode, the setup
process is the same.) NOTE: The IOS® device system need be 13.0 or above.
HOW TO ADJUSTMENT TURBO SPEED
Hold down the TURBO key and press one of the corresponding A, B, X, Y, L, ZL,
R, ZR keys for TURBO mode settings. Repeated operations can switch or cancel
automatic TURBO mode. Three Turbo speed setting: 5-10-15HZ.(default middle
speed) Press and hold the “Turbo + R3” button can adjust the controller
shooting speed.
“Turbo+R3 up” increase the shooting speed by 1 level. “Turbo+R3 down” decrease
the shooting speed by 1 level.
SWITCH® SIX-AXIS CALIBRATION SETUP
If the axis sensor is not calibrated, you can use any of the following
instructions to recalibrate it. Connection State: 1.Access sensor calibration
on the console: “System Setting” > “Controllers and Sensors” > “Calibrate
Motion Controls” 2.Keep the controller flat and press “+” or “-“. 3.When
“calibration completed” shows, it’s done.
Shutdown State: 1.Press and hold the “A” +”-” + “HOME” button for 3 seconds to
turn on. 2.Two groups front and rear lights flashing. 3.press “+” until LED
turn off, then the calibration is completed.
RGB LIGHT EFFECT SETUP
You can long press the “LIGHT” button at the back of the controller to switch
or turn off the RGB light effect. Press the “LIGHT” + “R3” button to switch
four light effect modes: Dazzling Light Mode Press “LIGHT” + “L3” button
briefly to pause and save the current effect mode. Single Color Light Mode
Press “LIGHT” + “L3” briefly to switch the light color. Single Color Breathing
Light Mode Press “LIGHT” + “L3” briefly to switch the light color. Single-
Color Breathing Cycle Light Mode Press “LIGHT” + “L3” briefly to pause and
save the current mode, press again to resume the Breathing mode.
In any mode, press “LIGHT + UP/DOWN” button to adjust RGB light brightness:
“LIGHT+UP” increase brightness. “LIGHT+DOWN” decrease brightness.
VIBRATION INTENSITY ADJUSTMENT
1. Four adjustable vibration intensity : 100%-75%-50%-0% 2. Press and hold
the Turbo + L3. 3. Turbo + L3 up to increase motor vibration strengthen. 4.
Turbo + L3 to decrease the motor vibration.
3D JOYSTICK CALIBRATION SETUP
If L3 or R3 are not centred, you can calibrate it through the console: 1.Press
on “System Setting”>”Controllers and Sensor”> “Calibrate Control Sticks”
2.Follow console instructions for calibration.
BUTTON TEST
If controller buttons fail or do not respond, use the console’s button test
option to check button functionality: Go on “System Setting”>”Controllers and
Sensors”>”Test Input Devices”>”Test Controller Button” Then the symbol for the
button you press will appear on the screen
RESET FUNCTION
To reset the Controller press the Reset button at the bottom of the
Controller.
WAKE UP/RE-CONNECTION FUNCTION
1. Press HOME for 1 second to wake up and reconnect the Controller to the
Switch® console. 2. It sleeps automatically if the connection fails after 15
seconds. 3. Press HOME button to wake up and reconnect to the last mode used.
PRECAUTIONS
Do not use NEXUS controller for purpose other than those outlined in this
Quick Star Guide. Store and use the controller in a dry area, protected from
moisture and direct sunlight. Elevated temperatures can damage the controller.
Do not disassemble the controller. Stop playing with the controller, if you
are uncomfortable or tired. Please, consult a doctor if symptoms persist. Take
some regular time out of play. This controller is not intended for children
younger than 3 years. To protect the environment, NEXUS controller cannot be
disposed with household waste. Please return this controller to a designated
collection point for recycling
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
·Reorient or relocate the receiving antenna.
·Increase the separation between the equipment and receiver.
·Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
·Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
www.nitho.com
SERVICE & SUPPORT If you have any questions or require support, contact NITHO
Team at support@nitho.com
or visit our website www.nitho.com
NiTHO GmbH – Victoriastrasse 3b – 86150 Augsburg – Germany
SUPPORT@NITHO.COM
WWW.NITHO.COM
NITHOGAMES
NITHOGAMES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>