FANAWAY Montclair Ceiling Fan Instruction Manual

FANAWAY Montclair Ceiling Fan Instruction Manual

THANK YOU FOR PURCHASING

Thank you for purchasing this quality Fan away product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this ceiling fan. Please keep instructions for future reference.

SAFETY PRECAUTIONS

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
   Cleaning and maintenance shall not be undertaken by children without supervision.

2. Children should be supervised to ensure that they do not play with the appliance.

3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring rules.

4.  Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
   Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water and get into the food chain, damaging your health and well-being.

5. The structure to which the fan is to be mounted must be capable of supporting a weight of 48kg.

6. The fan should be mounted so that the blades are at least 2.3 m above the floor

7. This fan is suitable for indoor use only. Mounting the fan in a location where it is subject to water or moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void the warranty.

8. Electrical installation should be performed by a qualified licensed electrician.

9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.

10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.

11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
    sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons.

PARTS LIST

• Unpack your ceiling fan carefully. Remove all parts and hardware.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Check whether the ceiling fan has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
• Examine all parts, you should have the following list and Fig.1:
  
  

INSTALLING THE MOUNTING BRACKET

• The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the blade to the nearest objects or walls.
• Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 48kg, with two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)
  
  

NOTE: The bracket screws provided are for use with wooden structures only. For structures other than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the mounting surface and the surrounding environment.

ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 8 degree angled ceiling installation.

INSTALLING THE FAN

INSTALLING THE DOWN ROD (Fig. 4)

1. Remove the ball joint (2) and dowel pin (3) by loosening the set screws (4) from the down rod (6).
   Remove the hitch pin (9) by removing the lock clip (10) (Fig. 4.1).
   NOTE: Do not discard keep these parts, they are required to reassemble later

2. Loosen the set screws (11) on the down rod coupling housing (8). (Fig. 4.2)
   

3. Carefully feed the fan wires (1) up through the down rod (6). (Fig. 4.3)
   

4. Assemble the down rod (6) into the down rod coupling housing (8), by inserting and line up the down rod coupling housing holes with the down rod holes and insert the hitch pin (9) and secure with the lock clip (10). (Fig. 4.3)

5. Secure the down rod (6) by tightening the set screws (11). (Fig. 4.4)
   
   

6. Insert the decorative cover (7) onto the down rod (6) to cover the down rod coupling housing (8). (Fig. 4.5)

7. Insert the canopy (5) over the down rod (6) and install the ball joint (2) and dowel pin (3) back onto the down rod (6) and secure by tightening the set screws (4). (Fig. 4.5 and Fig. 4.6)
   
   

HANGING THE FAN

Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig. 5)

LIGHT KIT INSTALLATION

LIGHT KIT INSTALLATION (Fig. 6 & 7)

1. Loosen the screw (1) from the fan bracket. Align the two slot screws with the keyhole slots (2) of the light kit bracket. (Fig. 6)
   

2. Turn the light kit counterclockwise until the slot screws are firmly at the end of the slots (2).

3. Secure screw (1) to the lamp shade bracket. Tighten all three screws. Do not over-tighten.

4. Connect the quick connector to the lamp holder part (3). (Fig. 7)
   

5. Secure the lamp-holder part (3) to the light kit bracket by tightening the 3 screws. Do not over tighten.

6. Install globes (4) into the lamp holders. Do not exceed the maximum power rating

ELECTRICAL WIRING DIAGRAM THE FAN

WARNING: FOR YOUR SAFETY, Electrical installation should be performed by a qualified licensed electrician.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED

WIRING.
From mains supply to mounting bracket terminal block: (Fig. 8)

1. Connect the live supply wire to the “L” terminal of the terminal block on the mounting bracket.
2. Connect the neutral supply wire to “N” terminal of the terminal block on the mounting bracket.
3. Connect earth wire to the “ ” earth terminal of the terminal block on the mounting bracket.

From mounting bracket to receiver and fan motor : (Fig. 8)
Connect the supply wiring quick connector from the mounting bracket to the input quick connector of the fan receiver . (Fig. 8)
Connect the output wires quick connector of fan receiver to the input wires quick connector of the fan assembly. (Fig. 8)

• Carefully insert the Remote Receiver above the hanger ball in the remainder spacing in the mounting bracket. Take care not to damage or loosen any of the wiring. (Fig. 9).
  
  

FINISHING THE INSTALLATION

• After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan wiring via the quick connector plug.

• Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s accessible metal body and lamp base back to the earth terminal at the terminal block on the mounting bracket.

• Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using the screws provided. (Fig. 10)
  

• Switch ON mains power supply to the fan. Test the fan operations or enjoy using the fan following instructions the under “USING YOUR CEILING FAN” section of this instruction manual.

USING YOUR CEILING FAN

Your ceiling fan is controlled via the remote control. There are 4 buttons (HI, MED, LOW, OFF) to control the fan speed and one button to control light on/off. Fig. 13
Before operating the remote, the following must be considered.

• 2 x AAA 1.5V (size) batteries are required to operate the remote control. Remove the battery cover
  from the back of the remote and insert 2 x AAA batteries. Ensure the polarities are correct as shown in the battery compartment. (Fig.11) (Batteries not included.)
  

• The remote (transmitter) and receiver must be configured so that communication between each other is paired up. This is achieved by setting the DIP switch on the receiver and remote on the same setting. (Fig. 12)
  
  Note: The DIP switch assembly has 4 switches which can be setup to 16 different transmitting code combinations. This is practical when there is more than 1 remote/receiver pair operating locally or in the same room.
  Note: To access the receiver DIP switches, remove the DIP switch cover.
  

OPERATING THE REMOTE:
Before you start using the remote, take the time to read through this section and get familiar with the buttons and function of each button.

LED Indicator
The red LED indicator on the top of the transmitter will flash when the buttons are active.

BUTTONS ON THE REMOTE

HI: Press the button to set fan running at High speed.
MED: Press the button to set fan running at Medium speed.
LOW: Press the button to set fan running at Low speed.
OFF: Press the button to turn OFF the fan
 : Press the button to turn ON/ OFF the light.

The remote has memory function. If the fan or light is turned off by the isolating switch, it will memories and recover the last status when turned on next

INSTALLATION OF THE REMOTE CONTROL HOLDER (Fig. 14)

1. Locate a suitable wall or surface to fix the remote control wall holder.

2. Remove the screw cover and install the holder using the 2 screws and re-install the screw cover. (Fig.14a).
   

3. Slide the remote into the holder. (Fig. 14b).
   

REVERSING FUNCTION (Fig. 15)
Your ceiling fan can operate in either summer or winter mode

SUMMER Mode: The reverse switch should be in the SUMMER position to rotate the fan in an anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch should be in the WINTER position to rotate the fan in a clockwise direction.
The airflow will be directed upwards assisting in the circulation of warm air, for energy conservation in winter.

AFTER INSTALLATION

WOBBLE:
NOTE: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet. If the fan was mounted rigidly to the ceiling it would cause excessive vibration. Movement of a few centimeters is quite acceptable and DOES NOT suggest any problem.

TO REDUCE THE FAN WOBBLE:
Please check that all screws which fix the mounting bracket and down rod are secure.
NOTE: This fan has been precision balanced at the factory and will not need to be balanced again.

NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in fan motor noise. This is normal. Please allow a 24-hour “settling-in” period, most noises associated with a new fan disappear during this time.
Please note that this is not a product fault and as such is not covered under warranty – All electric motors are audible to some extent.

CARE & CLEANING

NOTE: Always turn OFF the power at the mains switch before performing any maintenance or attempting to clean your fan.

• Every 6 months periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please turn off electricity power when you do so.
• Do not soak or immerse your ceiling fan in the water or other liquids. It could damage the motor or the blades and create the possibility of an electrical shock.
• Ensure that the fan does not come in contact with any organic solvents or cleaners.
• To clean the fan blade, wipe with only a damp clean cloth with NO organic solvents or cleaners.
• The motor has a permanently lubricated ball bearing so there is no need to oil.

SAFETY PRECAUTIONS FOR BATTERY

• WARNING – Keep new and used batteries away from children.
• CAUTION – Do not ingest battery—Chemical burn hazard.
• Always use 2 x AAA battery type with this ceiling fan remote controller.
• Ensure the batteries are inserted with the correct polarity.
• To prevent false operation during battery insertion or replacement, this ceiling fan must be disconnected from the supply mains.
• Remove batteries from the product when not in use for long periods of time.
• Batteries must be removed from the remote transmitter before it is discarded.
• Dispose of exhausted batteries immediately and safely (so they cannot be retrieved by children). Batteries can still be dangerous. Contact your local council to safely dispose of the battery.
• Regularly check the product and make sure the battery box lid is correctly secured. If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. If you suspect your child has swallowed or inserted a button battery, call the emergency number of your country if you are in Europe for fast, expert advice.
• Battery Leaks: Battery contains chemicals and should be treated as any chemical would. Take precautions when handling leaked battery chemicals. Battery chemicals should not be placed near the eyes or ingested. call the emergency number of your country if you are in Europe for fast, expert advice.

TECHNICAL INFORMATION

/ SKU# 511060 / SKU# 511061
Rated Voltage| 220-240V~ 50Hz
Rated Wattage (Motor)| 60W
Rated wattage (Lamp)| E27, 3 x Max.25W
Weight| 12kg
Canopy Dimensions| H:55mm     Dia:130mm

IN EUROPE – If you are a European customer please contact the retail outlet where the fan was purchased for warranty service.

Contact Us

Beacon International Ltd
Hong Kong Head Office: Room 05, 18/F, Kimberland Center, 55 Wing Hong Street, Cheung Sha Wan Kowloon, Hong Kong
Tel +852 34915904
Fax +852 34915917
China showroom / Office: 11/Fl, Guzhen Lighting Building B, Mid Zhongxing Road, Guzhen, Zhongshan, GuangDong, China.
Tel: +86 760 8986 6388
Fax: +86 760 8986 6380
info@beaconinternational.com
www.beaconinternational.com

Beacon Lighting Europe GmbH
Campus Fichtenhain 42, 47807 Krefeld, Germany
TEL +49 (2151) 325 82 39
FAX +49 (2151) 325 70 65
sales@beaconlighting.eu
www.beaconlighting.eu

References

• Homepage
• Beacon Lighting Europe – Fans and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>