Finder Q3MAX WiFi AP Repeater User Guide

September 23, 2024
finder

Q3MAX WiFi AP Repeater

“`html

Product Specifications:

  • Model: wifiRepeater-xxxx
  • Network: Dual band 2.4G & 5G
  • IP Address: 193.168.11.1

Product Usage Instructions:

Power and Signal Indicators:

Power LED: The power on indicator is on.

Signal LED: After powering on for about 10
seconds, the signal indicator is on, allowing connection settings
to be made.

Repeater LED and LAN LED:

Repeater LED: Indicates successful expansion,
with the repeater LED indicator lit up.

LAN LED: The network port indicator lights up
when connected to a network cable or superior route.

WPS Connection:

WPS LED: WPS connection indicator. Press and
hold the Reset/WPS button for 7 seconds to return the device to
factory state.

Configuration and Connection:

After successful expansion, you can modify the name and ensure
the password matches the original router password. Configure the
settings until successful. Return to your mobile device or computer
to select WiFi connection for internet access or connect directly
via LAN port.

In the administrator login interface, select language for
operation. Follow the steps for AP mode configuration. Modify name
and password as needed. Return to your device for extended WiFi
connection for internet access.

FCC Compliance:

This device complies with part 15 of the FCC Rules. It must not
cause harmful interference and must accept any interference
received. Unauthorized changes may void the user’s authority to
operate the equipment.

Frequently Asked Questions (FAQ):

Q: How do I reset the device to factory settings?

A: Press and hold the Reset/WPS button for 7 seconds until all
indicator lights turn off.

Q: How do I know if the repeater is successfully

connected?

A: The Repeater LED indicator will light up once the expansion
is successful.

“`

/ WPS

Power/signal LED WPS LED Repeater LED LAN LED
LAN

wifiRepeater-xxxx, WIFI 193.168.11.1 WiFi

WiFi LAN

AP WiFi

Dual band 2.4G&5G

Power LED The power on indicator is on

Signal LED

After power on for about 10 seconds,the signal indicator is on, Connection settings can be made

The expansion is successful,the Repeater LED indicator route,and the indicator
light is on

LAN LED

The network port indicator connects to the network cable, onnects to the superior route, and the indicator lights up.

WPS LED

WPS connection indicator

Reset/ WPS Button

Press and hold for 7 seconds,and all the indicator lights are off,The machine returns to the factory state. Short press for 2 seconds,WPS indicator flashes;After the connection with the superior router is successful. the indicator is on

When the machine enters the power on state,the signal indicator light is on,use the mobile phone or computer WiFi to search and connect Repeater- xxxx,click the connection, then will automatically jump to the setting page(if the jump interface does not apper, you need to the WiFi connection again.If this operation is still invalid,you can manually enter the website 192.168.11.1 in the browser),After entering the administrator login interface ,select the language for the next operation. The next step in relay mode is as shown in the figure.Select thesuperior network WiFi to be extended and enter the password

After cxpansion ,the name can be modified. The password is consistent with the original router password.Continue to the next step until the display configuration is successful.Return to the mobile phone or computer and select WiFi connection after expansion to surf the Internet,or connect the computer to surf the Internet directly through LAN port network cable

After entering the administrator login interface, select the language for the next operation.The next step in AP mode is shown in the figure.The name and password can be modified.Contiue to the next step until the display configuration is successful.Return to the mobile phone or computer and extended WiFi connection to surf the Internet

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals