InfiRay CW905nm Multi Spectral Thermal Imaging Binocular Instruction Manual

: September 25, 2024
: InfiRay

InfiRay CW905nm Multi Spectral Thermal Imaging Binocular

Product Information

Specifications

Product: Multi-spectral Thermal Imaging Binocular
Model: V1.0
Laser: CW905nm EN 60825-1:2014/A11:2021
Intended Use: Displaying heat signatures during nature observation, remote hunting observations, and civil use
Manufacturer: InfraOutdoor

Product Usage Instructions

Safety Information

Environmental influences: Avoid pointing the lens directly at intense heat sources like the sun or lasers to prevent damage. Use caution to prevent hazardous radiation exposure.

Ergonomics notes: Take breaks during extended use to prevent wrist pain.

Risk of swallowing: Keep the device away from small children to prevent swallowing of small parts.

Power Supply Safety Instructions

Check power supply components for damage before use.
Do not use defective parts; replace them immediately.
Avoid using the power supply unit in wet or humid environments.
Use only the original cable provided with the battery charger.
Avoid making any technical modifications to the device.

Disposal Information
Follow local regulations for disposing of electrical and electronic devices and batteries. Do not dispose of batteries as unsorted municipal waste. Return them to designated collection
points for recycling.

Intended Use
The device is designed for displaying heat signatures during nature observation, remote hunting, and civil use. It is not suitable for children and should be used as described in the
operating manual to avoid damages.

FAQ (Frequently Asked Questions)

Q: Can I use the binoculars for stargazing?
A: No, the device is specifically designed for displaying heat signatures and is not suitable for stargazing purposes.
Q: How do I clean the lenses of the binoculars?
A: Use a soft, lint-free cloth to gently wipe the lenses. Avoid using any harsh chemicals or abrasive materials that may damage the lens coatings.
Q: Can I recharge the battery using a different cable?
A: It is recommended to only use the original cable provided with the battery charger to ensure safe and proper charging.

IMPORTANT SAFETY INFORMATION

Environmental influences
WARNING! Never point the lens of the device directly at intense heat sources such as the sun or laser equipment. The objective lens and eyepiece can function as a burning glass and damage the interior components. The warranty does not cover damage caused by improper operation.

WARNING! Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Ergonomics notes

Caution: Take breaks after longer periods of use to avoid wrist pain.

Risk of swallowing

Caution: Do not place this device in the hands of small children. Incorrect handling can cause small parts to come loose which may be swallowed.

Safety instructions for use

Handle the device with care: rough handling may damage the internal battery.
Do not expose the device to fire or high temperatures.
Only use the battery charger included in the delivery package.
The maximum operating temperature of the adapter is 25°C.
The battery capacity decreases when operated in a cold ambient temperature. This is not a fault and occurs for technical reasons.
The recommended temperature for using this product is -25° to +55°.
Temperature exceeding this range will affect the service life of the product.
Do not store the device for long periods at temperatures below 25°C or above 50°C, or this will permanently reduce the capacity of the battery.
Always store the device in a dry, well-ventilated space.
If the device has been damaged or the battery is defective, send the device to our after-sales service for repair.
Before using this product in an environment with water, ensure that the USB-C connector is tightly covered.

Safety instructions for the power supply unit

Check the power supply unit, cable and adapter for visible damage before use.
Do not use any defective parts. Defective components must be replaced.
Do not use the power supply unit in wet or humid environments.
Only use the original cable provided with the battery charger.
Do not make any technical modifications.

For further information and safety instructions, please refer to the Operation Manual provided. This is also available on our website in the download center: www.infirayoutdoor.com.

User information on the disposal of electrical and electronic devices (private households)
The WEEE symbol on products and/or accompanying documents indicates that used electrical and electronic products must not be mixed with ordinary household waste. For proper treatment, recovery and recycling, take these products to the appropriate collection points where they will be accepted without charge. In some countries, it may also be possible to return these products to your local retailer when you purchase a corresponding new product. The proper disposal of this product serves to protect the environment and prevents possible harmful effects on human beings and their surroundings, which may arise as a result of incorrect handling of waste. More detailed information on your nearest collection point is available from your local authority. In accordance with state legislation, penalties may be imposed for the improper disposal of this type of waste.

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

For business customers within the European Union
Please contact your dealer or supplier regarding the disposal of electrical and electronic devices. He will provide you with further information.

Information on disposal in other countries outside of the European Union
This symbol is only applicable in the European Union. Please contact your local authority or dealer if you wish to dispose of this product and ask for a disposal option.

Intended use
The device is intended for displaying heat signatures during nature observation, remote hunting observations and for civil use. This device is not a toy for children. Use the device only as described in this operating manual. The manufacturer and the dealer accept no liability for damages which arise due to non-intended or incorrect use.

Function test

Before use, please ensure that your device has no visible damage.
Test to see if the device displays a clear, undisturbed image.
Check that the settings for the device are correct. See the notes in the section Operation.

Observation with and without glasses
Thanks to the flexible eye-shade, the GEMINI series can be used with or without glasses. It offers a full field of view in both cases.

Speciﬁcations

Model	GEL35R	GEH50R

Thermal Imaging Specifications
Resolution, pixel| 384×288| 640×512
Pixel Size, μm| 12| 12
NETD, mk| ≤25| ≤25
Frame Rate, Hz| 50| 50
Objective Lens, mm| 35| 50
Field of View, °| 7.5×5.6| 8.8×6.6
Optical Magnification, ×| 4.8~19.2| 4.1~16.4
Detection Distance (human 1.7×0.5)| 1800| 2600
Digital Night Vision Imaging Specifications
Resolution, pixel| 1920×1080
Pixel Size, μm| 4
Frame Rate, Hz| 50
Objective Lens, mm| 35
Field of View, °| 9.4×7.0
Optical Magnification, ×| 3.8~15.2
Laser Rangefinder
Max,Rangefinder Distance,m| 1200
Measuring Accuacy，m| ±1(3-100m); ±(1+L×0.25%)(100-1200m,L is the distance to the target)
---|---
Eyepiece
Focal Length of Eyepiece,mm| 12.5
Magnification, ×| 20
Eye Relief, mm| 15
Eye Relief Diameter, mm| 7
Diopter Adjustment, D| -5~+5
Available Pupillary Range, mm| 61~72
Display
Resolution,pixel| 1024×768×2 OLED
Size,inch| 0.39
Battery Specifications
Battery Type/Capacity/Output Voltage| Two 18650 Lithium-ion batteries /3.2Ah/3.7V
Voltage| 7.4
System Functions
Digital Zoom, ×| 1~4
Image Mode| Visible light, infrared (white hot, black hot, red hot, iron), fusion
Intelligent Image Algorithm| Infrared highlight, Infrared edging, hotspot tracking
PIP| √
Full color fusion| √
---|---
Image Capture and Video/Audio Recording| √
Video Playback| √
Wi-Fi Transmission (ios & android)| √
Electronic compass| √
Microphone| √
940nm Infrared Flashlight| √
Type-C interface| Power supply, data export, firrmware update
Other Specifications
IP Rate| IP66
Memory，GB| 32GB EMMC interface| 64GB EMMC interface
Operating Temperature，℃| -25~+55
Weight (no battery)，g| <900| <960
Dimension，mm| 198x154x78
Operating Time，h| >6

Actual operating time will depend to what extent the Wi-Fi and built-in video recorder is used.
Improvements may be made to the design and software of this product to enhance its features without prior notice to the customer.

Package Contents

Product Overview
GEMINI series binocular have integrated high-sensitivity thermal imaging detector, laser range finding, Wi-Fi, DMC, microphone and 1024×768 OLED. The 1920×1080 visible light Min. illumination detectors are available for some models. It is ultra-light in body, plug-and-play, smart and simple and can bring you excellent holding experience. The binocular can be used for 24/7 observation, it is suitable for scenarios such as police and law enforcement, mountain forest protection, geological prospecting, wildness security protection, etc.

Main Functions

Image capture, recording, and video playback
Wi-Fi image transmission
PIP, Hotspot Tracking , Fusion, Infrared highlight, Infrared edging
DMC
Laser range finding from 3m to 1200m
Adjust interpupillary distance between 61mm and72mm, and ±5D diopter
Mobile APP interconnection
Type-C power supply, data export, firmware update
Support multi languages such as English, German, Russian, French, Spanish, Portuguese, Italian, Czech, Polish, Hungarian, Dutch, Norwe-gian, Swedish, Slovak

Product Appearance

Figure 1 Front View

Figure 2 Rear View

Eye cup
Eyepiece
Down Button
Menu Button
Up Button
Camera Button
Range finding Button
Power Button
Laser Range Finding Window
Digital night vision Lens
Infrared lens
Lens Cap
Microphone
Interpupillary Distance Adjustment
Infrared Focus Ring
Neck strap buckle
Battery Compartment
Digital night vision Focus Ring
Type-C Interface
Tripod Interface
Focus ring: After the device is turned on, align at the observation target. When the distance of the observation target changes, the image may be blurred. At this time, you need to turn the focus ring to focus again until the image is clear.
Lens cap: When the device is not in use, you need to cover the lens cap to protect the lens.
Type-C data cable: This data cable supports power supply, data export, firmware update.

Button Descriptions

Button	Operation	Functions
**** Power Button	**** Short press	No menu：Standby/Wakeup With

menu：exit/return
Hold for 1.5s| Power on/off
Range Finding Button| Short press| Single range finding
Long press| Start/ End continuous range finding
Camera Button| Short press| Image capture
Long press| Start/stop video recording
Up Button | Short press| No menu：E-zoom cycles through 1×~4×, step 1×
With menu：move upwards/toggle parameters
Long press| No menu：PIP Mode cycles through Off,IR,NV and Fusion
With menu：the option is shifted left in time/ magnetic declination settings interface
Menu Button M| Short press| No menu：enter the shortcut menu
With menu：enter the next menu or confirm/cancel
Long press| No menu：enter the system menu
With menu：exit the shortcut/system menu
Down Button| Short press| No menu：Image Mode cycles through NV, IR and Fusion
With menu：move downwards/ toggle parameters
Long press| No menu：Color Palettes cycle through WhoteHot,BlackHot, RedHot and Iron
With menu：the option is shifted right in time/ magnetic declination settings interface
Up Button+Menu Button| Short press| Shutter correction
Long press| Background correction
Down Button+Menu Button| Short press| Switch between Day and Night in visual scenarios
Long press| Switch among General, Highlight and Edging in Infrared scenarios
Up Button+Down Button| Short press| No menu：enter fusion settings interface
Long press| Zero declination angles of the DMC Settings

Types of Power Supply

Type 1:Insert two 18650 batteries into the binocular following the below illustration, pay attention to the polarity.

Figure 3 Types of Power Supply

Type 2:Connect one end of the Type-C cable (20) to the Type-C connector(19) on the binocular, connect the other end of the Type-C cable (20) to the power adapter (21). Insert the adapter plug (21) into the 110-240V socket (22).
The nominal voltage and current is 7.4V/0.4A with battery as power supply, and the nominal voltage and current is 5V/0.6A when powered via Type-C cable.
During use, the power is low if the battery icon turns red. Please eplace the battery or power the device using a Type-C cable to avoid data loss.
Never use a damaged or modified charger.
Don’ t leave battery unattended when charging.
Do not expose the battery to high temperature or to a naked flame.
Do not remove the battery when the binocular is on.
Avoid using the battery at the temperature above the temperature shown in the table, this may decrease the battery’ s life.
Store the device in a dry and ventilated environment.
Keep the battery out of the reach of children.

Mounting of IR Illuminator
The IR illuminator with wavelength of 850nm or 940nm can be mounted on the binocular in lowlight conditions and in the darkness.

Figure 5 IR Illuminator Mounting Illustrations

Quick Start Guide

Power device on: Long press the power button（8）for 1.5 secs, the starting logo will be displayed on the screen after 1 second.
When an infrared image is displayed in the eyepiece, the binocular enters the operating status.
Rotate the diopter adjustment knob (2) to adjust the resolution of the icon on the display. The diopter adjustment knob is used to adjust the eyepiece diopter for users with different
degrees of myopia.
Quick Menu: On the home screen, short press the menu button (4) to open quick menu, then the WiFi, DMC, Microphone, Hotspot Tracking and IR Enhance can be set. Short press Up button (5)/Down button (3) to toggle among the different function options and short press the menu button (4) to switch parameters, short press the power button (8) to exit/back to the previous level.
System Menu: On the home screen, long press the menu button (4) to enter the system menu interface to get more functions. Short press the Up button (5)/Down button (3) to toggle among different function options, short press the Menu button (4) to switch parameters, then short press the power button (8) to exit/back to the previous level.
Image Capture/Video Recording: On the home screen, short press the Camera button (6) to start/end image capture. Then long press the Camera button (6) to record videos.
Laser Range Finding: Short press the LRF Button (7) to perform single range finding; Long press the LRF button (7) to perform continuous range finding.
Power Device Off：Long press the power button (8) for 3 secs, the shutdown interface will be displayed in 3 secs. Release the power button (8) to cancel during shutdown count down.
Standby: On the home screen, short press the power button (8) to enable standby mode. Short press the power button (8) again to wake up the device. The device will shut down after standby for 30min.

Status Bar

Time and date: display the current time and date. It can be modified in System Menu→ System Settings→ Time Settings.
Image Mode: short press the Down button (3)to switch among visible light NV , Infrared IR and Fusion FU.
Infrared Polarity：long press the Down button (3) to switch among Whitehot, Blackhot, Redhot and Iron.
Image Scenarios：In NV Mode，short press the Down button (3)
+Menu button (4)，switch between Day and Night In IR Mode， long press the Down button (3)+Menu button (4)，switch among General , Highlight , Edging .
Electronic zoom: short press the up button (5), electronic zoom -/+, step size is 0.1×, the image can be reduced/enlarged by 1×~4× at the center of the display; long press the up button (5), electronic zoom -/+, step size is 1×.
Laser Range Finding：short press the LRF button (7)，for single range finding ；Long press the LRF button (7） for continuous range finding ；
Storage capacity: when the remaining storage capacity is less than 100M, this icon will be displayed.
Microphone: set through Shortcut Menu→ Startup. When microphone is enabled, the icon will be displayed.
Wi-Fi image transmission: set through Shortcut Menu→ Startup. When Wi-Fi is enabled, the icon will be displayed.
Type-C：when Type-C cable is connected, the icon will be displayed: display
Battery level：real-time battery level display，display when the battery level is low，display when no battery is inserted.
Azimuth: display the current azimuth information in real time. When it is used for the first time or the location is changed, it can be calibrated through System Menu→Location→DMC.
Pitch angle: display the current pitch angle information in real time. You can calibrate it through System Menu→Location→DMC when it is used for the first time or the location is changed.
Tilt angle: display the current tilt angle information in real time, and it can be calibrated through System Menu→Location→DMC when it is used for the first time or the location is changed.
Range finding distance: short press the range finding button to display the range finding distance in real time.

Image Calibration

When the image is degraded or non-uniform, it can be improved by calibration. Calibration can equalize the background temperature of the detector and eliminate the image defects (such as vertical stripes, phantom images, etc.). There are two calibration modes – Shutter Calibration and Background Calibration.

Shutter Calibration：Short When the image is degraded or non-uniform, it can be improved by calibration. Calibration can equalize the background temperature of the detector and eliminate the image defects (such as vertical stripes, phantom images, etc.). There are two calibration modes – Shutter Calibration and Background Calibration.
Shutter Calibration：Short press the Up button (5) +Menu button (4)，the device will perform shutter calibration based on the software algorithm, it’s unnecessary to close the lens cap(the internal shutter blocks the sensor) for shutter calibration. The shutter calibration type can be set in the system menu. Refer to the System Menu-System Settings-Shutter Calibration Section.
Background Calibration：Short press the Up button (5) + Menu button (4), if the thermal image is not satisfying even after shutter calibration, you can try to close the infrared lens cap and click Yes to perform background calibration. As shown in the following figure：

Photography and Video Recording

GEMINI series is equipped with a function for video recording and photography of the observed image which is saved on the built-in 64GB memory storage. The photo and video files are named with time, so it is suggested to synchronize date and time in the InfiRay Outdoor application before using the photo and video functions，or you can synchronize Date & Time in System

Menu-Time-Satellite Time/Time Settings.

Photography

On the home screen, short press the Camera button (6) to capture an image.
When taking a photo, the photo icon flashes below the status bar in the upper left corner of the screen. The photo is taken successfully when the thumbnail appears on the bottom right corner of the screen.
Photos are stored in the built-in storage.
When “the memory space is insufficient” box is prompted on the interface, check and transfer videos and images to other media to free up the space.

Video Recording

On the home screen, long press the Camera button (3) to start the video recording function.
Then, the recording timer in the format of the HH: MM: SS (hour: minute: second) will appear on the upper left of the display.
The other operations to the device are supported during recording.
Long press the Camera button (6) again to stop and save the video recording.
All videos and photos will be saved in the build-in storage.

Digital Zoom

GEMINI series support to cycle switch digital zoom from 1× to 4× by short pressing the Up button (5)，in 1× increment.
The corresponding magnification is displayed in the status bar, as shown in the following figure:

Fusion Settings

Short press the Up button (5) + Down button (3) to enter fusion settings interface. As shown in the following figure:
Short press the menu button (4) to switch X/Y coordinate; Short press the Up button (5) to move the visual image leftward/upward by one step; Short press the Down button (3) to move the visual image rightward/downward by one step.
Short press the Power button (8) to exit, the parameters won’t be saved; Short press the Up button (5)+Down button (3), a prompt box will pop up: Save this operation? As is shown in the following figure：
Short press the Menu button (4) to cancel/confirm this operation.

DMC Zero Declination Angle Settings

During the installation or transportation of the DMC, there may be a slight deviation, resulting in a slight deviation in the DMC information. In this case, it can be addressed by setting zero declination angles of the DMC.

Long press the Up button (5) + Down button (3) to enter the DMC Zero Declination Angle Settings interface. As shown in the following figure:
Short press the Power button (8) to exit directly without saving the parameters; Short press the Menu button (4) to save the parameters and exit.

On the Home Screen，short press the Menu button (4) to enter the quick menu.
Short press the Up button (5) /Down button (3) to toggle between functions，then press the Menu button (4) to confirm.
Short press the Power button (8) to exit /back to the previous level, press and hold the Menu button (4) to hide the quick menu.

WiFi：short press the Menu button（4）to enable WiFi,disabled by default.
DMC: short press the Menu button（4）to enable DMC,disabled by default.
Microphone: short press the Menu button（4）to enable Microphone,disabled by default.
Hotspot Tracking: short press the menu button (4) to enable hotspot tracking, which will make real-time track on the hottest object on the screen mark with a 32*32 red box, disabled by default. As shown in the following figure when it is enabled.
IR Enhance：short press the Menu button (4) to enable IR Enhance to present more details, disabled by default.

System Menu Functions

On the Home Screen, long press the Menu button (4) to enter the system menu.
Press the Up button (5)/Down button (3) to toggle between functions, then press the Menu button (4) to select the option, press the UP button (5)/Down button (3) to switch parameters.
Press the Power button (8)to exit back to the previous level， press and hold the menu button (4) to hide the system menu.

Display Settings

Figure 20 Display Menu

Screen Brightness：real-time adjustment on screen brightness adjustment，adjustment range 1-5，3 by default.
Image Brightness：real-time adjustment on IR/NV image brightness，adjustment range 1-5，3 by default，supported in IR or NV mode.
Image Contrast：real-time adjustment on IR/NV image contrast, adjustment range 1-5, 3 by default, supported in IR or NV mode.
Reticle: the reticle will be displayed on the screen center when it is enabled, enabled by default.

Media

File Browse
Short press the Menu button （4） and turn to media browse interface. As shown in the following figure:

Image Browse

Short press Up button(5)/ Down button (3), move to select images, then short press Menu button (3) to present Play /Delete option. As shown in the following figure:

Figure 23 Image Selection Interface

Short press Up button (5)/ Down button (3) to select Play, then short press menu button (3) to enter full-screen play interface. As shown in the following figure:
On the play interface, short press Up button (5)/ Down button (3) to switch image/video, short press Power button (8) to return to the previous menu.

Video Browse

Short press Up button (5)/ Down button (3) to select the video, then short press Menu button (4) to present Play/Delete option. As shown in the following figure:

Figure 25 Video Selection Interface

Press Up button (5)/ Down button (3) to select Play, continue to short press Menu button (4) to enter full-screen play interface. As shown in the following figure:

Figure 26 Video Play Interface

Short press the Menu button (4) to pause on the full-screen play interface. As shown in the following figure:

Figure 27 Video Pause Interface

On video play interface, short press up button (5)/down button （3）to switch image/video, short press power button (8) to return to the previous menu.

mage/Video Deletion

On the media interface and full-screen image/video play interface, long press menu button (4) to present Delete interface. As shown in the following figure:
If the media file is empty, the prompt is as shown in the following figure:

Waterproof Overlay： When this function is enabled, date, DMC, and ranging distance information will be displayed on local recorded videos, captured images and Wi-Fi
transmission.

Location Settings

The built-in azimuth module should be calibrated if the binocular is transported from the manufacturing place to different places of use due to the influence of magnetic field and gravity. The calibration procedures are as shown in the following figure：
Magnetic Declination：the magnetic declination parameters can be set, as shown in the following figure:
Altitude Unit：Meter/Foot, meter by default.
Range-finding Unit：Meter/Foot, meter by default.

Wi-Fi Settings

Wi-Fi Name: can be viewed only, the name can be set via App, setting range is 1-32 characters, the initial name is GEMINI_the latter six characters of Mac, for example: GEMINI_78C132.
Encryption Type：None/WPA2， WPA2 by default.
Password：can be viewed only, the password can be set via App, setting range is 8-16 characters, the initial password is 12345678.

Time Settings

Date format：Y/M/D, D/M/Y or M/D/Y. Y/M/D by default.
Time zone settings：time zone can be set, local time zone is displayed by default.
Time settings：it can be used when the satellite time is disabled, the setting parameters are as shown in the following figure:

System Settings

Language：English / German /Russian / French / Spanish / Portuguese / Italian / Czech / Polish / Hungarian / Dutch / Norwegian / Swedish / Slovak, English by default.
Volume：adjustment range is 1-5, 3 by default.
Format：the image and video data will be deleted and cannot be recovered after formatting, so please backup first.As shown in the following figure：will be deleted and cannot be recovered after formatting, so please backup first.As shown in the following figure:
Restore system：the image and video data will be deleted and cannot be recovered after restoring system, all the parameters will restore to factory default settings, so please backup first.As shown in the following figure：
Shutter CORR:Auto/Manual,Auto by default.

About

Figure 45 About Menu

Storage info: total capacity, used capacity and remaining capacity are displayed on storage info. As shown in the following figure：
System information: The MODEL, device PN (DEV_PN),device SN (DEV_SN), infrared module PN (CORE_PN), infrared module SN (CORE_SN), ARM version, algorithm (ALG) version, LOGIC version, NIOS version, and MAC address are displayed on system info. As shown in the following figure:

Wi-Fi Function

The GEMINI series can be can connect with the mobile device (laptop or mobile phone) for data transmission via Wi-Fi function.

Turn Wi-Fi on in the quick menu. (For more information, please refer to Quick Menu-Enabled Items-Wi-Fi).
After the Wi-Fi function is on, search for the Wi-Fi signal with the name “GEMINI_XXXXXX” on the mobile device, XXXXXX is the last 6 digits of the device MAC address.
Select the Wi-Fi and enter the password to connect. The initial password is 12345678.
When Wi-Fi is successfully connected, it supports to control the device via the InfiRay Outdoor App downloaded in the mobile device.

Setting Wi-Fi Name and Password
The name and password of the Wi-Fi in GEMINI series can reset on the InfiRay Outdoor App.

After the device is connected to the mobile device, locate and click the ‘Settings’ icon on the InfiRay Outdoor image screen to enter the Settings interface.
In the text box, enter and submit the new Wi-Fi name (SSID) and password.
It needs to reboot the device to take the new name and password effect.

Note: If the device is reset to the factory settings, the name and password of the Wi-Fi will also be restored to the default settings.

Firmware Update

Notifications about updates will be posted on the official website or social media or InfiRay Outdoor APP.
Connect the PC to the device via Type-C cable, and open the USB flash drive on the PC.
Download the update file in the official website (www.infirayout-door.com) and store it to the folder named “update” in the memory space of GEMINI.
Long press the Power button (7) to reboot the device;
The device will automatically search for the update file stored in the folder named “update” in the memory space of GEMINI.
Please make sure the device is fully charged before updating.

InﬁRay Outdoor

GEMINI series thermal imaging binocular support InfiRay Outdoor Technology, which allows you to transmit the image from the binocular to smartphone or tablet via Wi-Fi in real time mode.
You can find the detailed instruction about InfiRay Outdoor at the site www.infirayoutdoor.com.
Download and install the InfiRay Outdoor at the official website (www.infirayoutdoor.com) or app store or scanning the QR code below.

Technical Inspection
It is recommended to carry out a technical inspection each time before using the binocular.

Check the following:

The appearance (there should be no cracks on the body).
The condition of the object lens and eyepiece (there should be no cracks, greasy spots, dirt or other deposits).
The battery status (it should be charged).
The controller/button should be in working order.

Maintenance

The maintenance should be carried out at least twice a year and includes the following steps:

Wipe the surface of metal and plastic parts to clear off dust and dirt with a cotton cloth. Silicone grease may be used for cleaning process.
Clean the electric contacts and battery slots on the device using a non- greasy organic solvent.
Check the glass surface of the eyepiece and lens. If necessary, clear off the dust and sand on the lens (it is perfect to use a non-contact method).

Use a specialized wiping tool and solvent to clean the optical surfaces.

Legal and Regulatory Information

Wireless transmitter module frequency range:
WLAN: 2.412-2.472GHz (For EU)
Wireless transmitter module power < 20dBm (only for EU)
We thus declare that the GEMINI multi-spectral thermal imaging binocular complies with the directives 2014/53/EU and 2011/65/EU. The full text of the EU declaration of conformity as well as additional information are available at: www.infirayoutdoor.com.
This device may be operated in all member states of the EU.

Body-worn Operation
This device was tested for typical body-support operations. To comply with RF exposure requirements, a minimum separation distance of 0.5cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
All rights reserved and shall not be copied and distributed in any form without written permission.