SIMRACING Formular Edition Racing Pedals Instruction Manual

: September 21, 2024
: simracing

Table of Contents

SIMRACING Formular Edition Racing Pedals
GENERAL INFORMATION
DESCRIPTION OF THE PEDALS.
WARNINGS AND SAFETY INSTRUCTIONS
BEFORE YOU START
INSTRUCTIONS FOR USE
MAINTENANCE
ATTACHMENTS
WARRANTY
TECHNICAL DOCUMENTATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIMRACING Formular Edition Racing Pedals

GENERAL INFORMATION

User Cautions

Please take time to read the safety and warning notes in this manual before using the pedals.
It is essential that you follow these instructions for the pedals for issue-free operation and to be able to file a claim under the warranty.
The pedals must be used for the purpose they have been designed. Any other use is considered dangerous. Any liability of the manufacturer for damage that may be caused by non-compliance with the instructions in the manual is excluded.
This manual contains important information about the operation of the pedals. For this reason it should always be kept within reach of the user.

Manufacturer’s Details:
Sim Racing Pro 2018 S.L
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel + 34 627 639 716
info@simracing-pro.com

Technical Service Details
Sim Racing Pro 2018 S.L
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel + 34 627 639 716
support@simracing-pro.com

DESCRIPTION OF THE PEDALS.

General description
This technical manual contains all the necessary instructions for the installation, commissioning, maintenance and use of the pedals.

Components:
One Base, 3 pistons, set of three pedals, accelerator, brake and clutch.

Electrical power supply of the machine:

Power and electricity consumption: 5 volts USB-C
Model: Sim Racing Pro . Total Power: 225mW . Total consumption: 45mAh
NOTE: These consumptions are always approximate since they depend on the performance of each element.

What’s included

set of pedals
1 pc Allen key nº3
1 pc Allen key nº4
1 pc Allen key nº5
1 pc. 10 mm open-end wrench
1 pc open end wrench 13 mm
1 x 2m USB cable / USB-C to USB-A
1 user manual / CE certificate
1 Warranty form

Working principle
The SRP GT 3p/2p pedals. They have the following functions: Driving Simulation

Intended use

Driving simulation when playing PC car racing games.
Do not carry out activities other than those for which the pedals have been designed with elements other than those indicated here.
Do not exceed the working capacity of the pedals. The manufacturer of the pedals may not accept responsibility in the event of failing to comply with this warning.

Important safety precautions

Pedals may be suitable for children over six years old, under appropriate adult supervision The fastening of the pedals is essential for their proper functioning.
An appropriate use of the pedals and a maintenance contribute to the life of the equipment.

Control panel

Note : The user must ensure that all the identification signs and warning plates on the pedals are maintained and preserved Under no circumstances should they be dismantled or altered.

WARNINGS AND SAFETY INSTRUCTIONS

Protection and safeguards
The materials used in the manufacture of the pedals do not have any hygienic risks, although in the event of fire the plastic components and lubricants may generate toxic fumes. Do not carry out any maintenance or cleaning operations on the pedals or the pavement in the vicinity without first disconnecting the USB from the P

STORAGE AND TRANSPORT

Check whether the pedals have been damaged during delivery.

Weight and dimensions

Model| Length, mm.| Width, mm.| Height, mm.| Weight, Kg.
---|---|---|---|---
SRP FORMULA-R| 441| 347| 245| 7,4 KG

Storage
No particular measures are recommended with regard to storage. However, If the user leaves it unused for a long time, it is recommended to protect it from dust by covering it properly and disconnecting it from any power source beforehand.

Transport and handling
Ensure the manual is available when moving the pedals from one location to another. Total weight of the pedals must be considered for transportation. The total weight of it must be taken into account.

DIMENSIONS

Note : This product has been designed to be assembled by the final user.

Unpacking
Upon receipt of the product, ensure that the assembly is done close to the final location of the pedals. Unpacking should be carried out with the utmost care and attention. The pedals should not be installed if any damage is observed during unpacking. If any doubt, refrain from using the pedals and contact the supplier for information.

Sep Up Location
The surface on which the machine is to be installed must support the weight of the pedals, as indicated in section 4.1 above. Pedals are recommended to be placed on a metal frame where they can be fixed correctly. They can also be placed directly on the floor on a carpet or rubber surface

Assembly
Once the product is located and set up in the place where they will work on, they can be installed and connected.

Electrical connection

The electrical connection of the pedals is 5V via USB. As indicated in the data sheet, or in the general dimensional and connection drawing.
The pedals require a stable, standardised supply voltage that is between the operating ranges of the pedals for proper operation. Faulty power supply to the pedals can lead to malfunction and even serious damage or deterioration of installed electrical components.
Make sure that the electric cables connecting the pedals are properly protected and they are not left in areas where they can cause in concenience.

BEFORE YOU START

Fastening
Check that the pedals have been levelled out correctly, as described in section 5.3.

Review with the pedals connected

INSTRUCTIONS FOR USE

Pre-inspection and adjustments

Before using the pedals, check that they are connected correctly.
Check the status of the LED indicators to determine that everything is correct. See point 6.2

Controls
The pedals have two/three pedals, depending on the model.

An accelerator
A Brake
A Clutch

CONTROL SETTINGS.

Key adjustment.
There are 9 positions for the keys. Unscrew the two Allen screws to move them (see attached drawing).

CAM ANGLE ADJUSTMENTS
By unscrewing the two screws A (see enclosed drawing) the cams can be adjusted in the range of 70° to 90°

Recommendations :

70º seat position in GT
90º seat position at Formula (lying down)
Applicable to the three cams accelerator, brake and clutch.

FIRMNESS ADJUSTMENTS
Loosen screw B (see drawing below) to raise the piston for more firmness and to lower it for less firmness. Applicable to all three pistons equally: accelerator, brake and clutch.

BRAKE TRAVEL ADJUSTMENTS
With the 13 mm spanner, turning the screw “A” (see attached drawing) to the left will shorten the travel with a minimum of 15 mm and turning to the right will increase the travel with a maximum of 45 mm of travel, once the desired travel is set, you must perform a calibration from the application to reset the minimum value and then adjust the maximum value manually to our desired braking pressure.

THROTTLE TRAVEL ADJUSTMENTS
By loosening the hexagon socket screw C (see enclosed drawing), unscrewing part D shortens the route. Unscrew a max. of 15 mm. The pedal is supplied at a maximum route

Download and use of the app.
App from the Download section on the SRP website simracing-pro.com Execute and follow the steps of the appl for a good configuration.

MAINTENANCE

General cleaning

Introduction

It is advisable to clean the pedals periodically to remove dust excess.
DO NOT use cleaning fluids in the area of the plate, as this could cause damage to the pedals.
Remember to keep the pedals in an optimum state of cleanliness and maintenance as this may improve their performance and life expectancy of the product.

Replacement of elements
The replacement of any element must be done by the technical service or by remote connection with the technical service Ensure power supply is fully disconnected before carrying out any maintenance or cleaning operations to the pedals or any other dispositive that pedals are attached to.

ATTACHMENTS

General Measures Diagram

CE” BRANDING
The plate is stamped with the manufacturer’s brand, the CE conformity brand and the manufacturer’s social information. Specific details of the pedals such as brand, model, serial number and year of manufacture, are displayed on the top of the plate

WARRANTY

The company SIM RACING PRO 2018, SL, is committed to ensuring the proper functioning of the pedals and the replacement of the elements that compose it due to a manufacturing defect. This warranty will be effective as long as the normal operation of the pedals has not been distorted or varied and the faulty element has NOT BEEN MISHANDLED OR MANIPULATED.

Warranty : 2 years from date of billing, except for electrical components and parts subject to normal wear and tear.