anko 69434310 Pet Retractable Mesh Gate Instruction Manual
- September 21, 2024
- Anko
Table of Contents
69434310 Pet Retractable Mesh Gate
Product Information
Specifications:
- Product: Pet Retractable Mesh Gate
- Usage: For pet use only
- Installation: Fitted between rigid walls (e.g., timber or
brick)
Product Usage Instructions
Installation:
-
Apply the safety gate to the wall and adjust the height of the
movable lower bracket to match the baseboards. -
Clean the surface, remove release paper from brackets, stick
safety gate to the wall with stickers. -
Press the C2 button to lift it up, then remove the safety gate
from brackets A1 & A2. -
Mark screw holes for A1 & A2, ensure they are vertical,
remove brackets, drill holes, insert expansion tubes, and fix
brackets properly. -
Place B2 into A2 and B1 into A1, ensuring proper bracket
alignment. -
Test the gate by opening it and ensuring the mesh is flat and
wrinkle-free. -
Install A3 brackets in desired position, mark screw hole
positions, drill, insert expansion tubes, and fix brackets
properly. -
Gate installation is complete. Ensure gate is locked when not
in use.
How to Use:
-
Press and turn the cap of the gate clockwise to unlock it.
-
Pull out the retractable mesh barrier, keeping it vertically
flat, and hook A4 & A5 to A3 brackets. -
Ensure A4 & A5 are securely hooked into the A3
brackets. -
Press and turn the cap of the gate counterclockwise to lock
it.
How to Remove the Gate from the Wall:
Press the C2 button and lift it up to remove the gate
easily.
Warning:
This mesh gate is for pet use only and should be fitted between
rigid walls like timber or brick. If unsure, seek professional
installation. Pet owner is responsible for determining if the mesh
gate is suitable for their pet.
Frequently Asked Questions (FAQ):
Q: Can this mesh gate be used for children?
A: No, this mesh gate is designed for pet use only.
Q: Can the gate be installed on any surface?
A: The gate should be fitted between rigid walls like timber or
brick. Consult a specialist if unsure about installation.
Q: How do I clean the mesh gate?
A: Use a damp cloth to gently wipe down the mesh gate. Avoid
using harsh chemicals that may damage the material.
PET RETRACTABLE MESH GATE
Instructions
Warmly notice:
Before installation, make sure the screws are suitable for the surface.
Shorter screws are used on wood surfaces. According to the hardness of the
wood surface, it may be necessary to pre-drill holes with 2.5mm diameter
before applying the screw. Longer screws and expansion screws are used in
solid walls such as concrete walls or tiled walls with skirting boards.
(Please pre-drill the holes on the solid wall before using the expansion
tube.) Shorter screws and expansion screws are used in solid walls such as
concrete walls or tiled walls without skirting board. (Please pre-drill the
holes on the solid wall before using the expansion tube.) Before installation,
make sure the 2x A3 pieces are on a proper surface.
If you are securing all the brackets along the same surface, your screws need
to be secured into holes A3A on the bracket. If you are securing your bracket
on the side through A3B holes, ensure your screws are secured into holes A3B
on the bracket.
How to installation
Step 1. Apply the safety gate to the wall lightly and adjust the height of the
movable lower bracket (B2) to where it’s suitable for the base boards. Place
A1 & A2 into B1 & B2 respectively. Please note: Always put the lower bracket
(B2) as close to the base board as possible. If there is no base board on the
wall, please do not place the lower bracket(B2) over 12cm from the floor.
Step 2. Clean the surface and let dry. Tear off the release paper from the
tapes on the brackets (A1 & A2). Stick the safety gate to the wall with the
stickers, note not to touch the adhesive side.
Step 3. Press the C2 button to lift it up, then the safety gate can be removed
out from A1 & A2.
Step 4. Mark the screw holes for A1 & A2 and make sure A1 & A2 are vertical.
Step 5. Remove the brackets (A1 & A2) from the wall, drill the marked screw
holes, insert the expansion tubes, and then use the screws to fix bracket (A1
& A2) properly.
Step 6. Place B2 into A2 and B1 into A1. Make sure that A1 & B1, A2 & B2 is
secured into their brackets properly.
Step 7. Test the gate by opening it and making sure the mesh is flat and
wrinkle free. Apply A3Open the safety gate, make sure the mesh is flat and
wrinkles free. Apply bracket A3 x 2 to the desired position and mark the
position of the screw holes for the A3 brackets accordingly. Make sure both
the A3 marks are vertical.
Step 8. Remove the 2x A3 brackets, drill the marked screw holes, insert the
expansion tubes and then use screws to fix the 2x A3 brackets properly.
Step 9. Installation of the gate is now complete. Make sure the gate is in the
locked position when not in use.
How to use
1. Press and turn the cap of the gate clockwise to unlock the gate.
2. Hold the handle and pull-out the retractable mesh barrier, keep the mesh
surface vertically flat and hook A4 & A5 to both A3 brackets.
3. Make sure that A4 & A5 are hooked well into the A3 brackets. 4. Press and turn the cap of the gate counterclockwise to lock the gate.
How to remove the gate from the wall
Press the C2 button, and lift it up to remove the gate easily.
WARNING:
This mesh gate is for pet use only. Mesh gate is to be fitted between rigid
walls e.g. timber or brick. If in doubt, we highly recommend you have a
specialist to install. It is the responsibility of the pet owner if this mesh
gate is suitable for their pet.