LIVARNO 452544_2310 LED Ceiling Light Instruction Manual
- September 20, 2024
- LIVARNO
Table of Contents
452544_2310 LED Ceiling Light
LED CEILING LIGHT
Assembly, operating and safety instructions
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device.
List of pictograms used
| Please read the operating instructions!
---|---
W| Watt (effective power)
HZ| Hertz (mains frequency)
V| Volt
|
Safety class II
| Observe warnings and safety notices!
IP20| The light has protection class “IP20” and is exclusively intended
for in- door use in private households.
| Polarity of the connection
| Allocation (alternating voltage)
| Polyethylene (low density)
**| Short-circuit proof safety transformer
| Direct current (type of current and voltage)
| Double insulation
| To prevent hazards, if an illuminant on this product is damaged, it must be
replaced by the manufacturer, its service representative or an equally
qualified professional.
| Lumen
| Colour temperature
| Electric shock warning! Danger to lifel
| This light is only suitable for indoor use in dry and enclosed spaces.
| For your safety
| Caution! Risk of burns due to hot surfaces!
| Dispose of the packaging and de- vice in an environmentally-friendly manner!
| Danger to life and risk of accidents for infants and children!
| This light is not suitable for external dimmers or electronic switches.
| The packaging is made from 100% recycled paper.
| Corrugated cardboard
| Paper
| Alternating current (type of current and voltage)
tc| Reference temperature point on the housing
ta| Highest rated/ambient temperature
SELV**| Safety extra-low voltage
| Other cardboard
| Colour rendering index
| Safety information Instructions for use
List of pictograms used
To prevent hazards, if an operating unit on this product is damaged, it must
be replaced by the manufacturer, its service representative or an equally
qualified professional.
LED Ceiling Light
Introduction
Congratulations on the purchase of your new appliance. You have selected a
high quality product. Please be sure to care- fully read all the instructions
for use. Fold out the page with illustrations. These instructions are part of
the product and contain important information on setup and handling. Always
observe all safety instructions. Before using this product for the first time
verify the correct voltage and that all parts are properly installed. If you
have any questions or are unsure about operating the product, please contact
your distributor or service centre. Please keep these instructions in a safe
place and pass them on to third parties if necessary.
Intended use
This light is only suitable for indoor use in dry and enclosed spaces. The
light can be mounted onto any normally inflamma- ble surface. This product is
only intended for private household use and not for commercial purposes. This
product is intended for normal operation and can be used for wall or ceiling
mounting.
Scope of delivery
Check that all the parts are present and that the appliance is in perfect
condition immediately after unpacking.
1 LED Ceiling Light (model 14162305L/ 141624021/14162508L) 4 lamp arms
(14162402L)
1 fastening plate (141624021)
1 connection housing (14162402L)
8 screws (lamp arms) (14162402L)
2 screw anchors
2 screws
1 screwdriver (141624021)
1 instructions for assembly and use
Parts description
- Mounting bracket
- Screw (connection housing)
- Connection housing
- Wall plug
- Screw (mounting bracket)
- Lustre terminal
- Junction box
- Protective tube
- Mains connection cable (external)
- Lamp arm
- Fastening plate (14162402L)
- Screw (lamp arm) (14162402L)
- Connection cable (14162402L)
Technical data
Light:
Model number: 14162305L/141624021/ 14162508L
Operating voltage: 230-240V~, 50 Hz
Max, rated power: 14162305L: max. 18W/14162402L: max. 16W/141625081: max.
15W/14162305L: max. 16.5W
Protection class: II/
IP rating: IP20
LED: LED module
Illuminant: Max. rated power: (3 x 5.5W)
141624021: так. 15.2W
141625081: max. 13W
(2 x 6.5 WI
Protection class ; II/
IP rating ; 1820
14162305L/141624021/14162508L:
This product contains illuminants from energy efficiency category “F”
Safety
Safety notices
Damage due to failure to comply with these instruc tions for use will void the
warranty! We assume no liability for consequential damages: We assume na
liability for property damage or personal injury due to improper handling or
failure to comply with the safety instructional Only use the included parts,
using other parts will void the warranty,
WARNING! DANGER TO LIFE AND ACCIDENT HAZARD FOR TODDLERS AND SMALL
CHILDREN!
Naver leave children unsupervised with the packaging material. The packaging
material poses a suffocation hazard. Children frequently underestimate the
dangers. Please always keep the product out of the reach of children.
- This device may be used by children aged 8 years and up, as well as by persons with reduced physical, sensory or mental capociles, or lacking experience and/or knowledge, so long as they are supervised or instructed in the sole use of the device and understand the associated naks Do not allow children to play with the device. Cleaning and user maintenance must not ba performed by children without supervision
Avoid the risk of fatal injury from electric shock
- Ensure that a qualified electrician, or a person trained to carry out electrical installations, pee forms the alectrical installation
- We assume no liability for property damage or personal injury due to improper handling or failure to observe the safety norices!
- Never use the light if any defects have been identified.
- Prior to installation, remove the fuse or switch off the circuit breaker (arting) in the fuse box
- Ensure that the light does not come into contact with water on other liquids under any circum stances
- Prior to installation, verify the avalable mains vohage corresponds with the operating voltage required for the light (see “Technical data”).
- Be sure not to damage any wires during installation.
- Never open any of the components of the elec trical equipment or insert any objects into the some components. This will pose a risk of fatal Injury from electic shock
Prevent fire and injury hazards
- To prevent bums, be sure the light is switched off and cooled down before touching it Do not attach the light to a damp or conductive substrate.
- Do not look directly into the light source (lamp, LED, etc). Do not look into the light source flamp LED, etc.) with an optical instrument le.g. mag- nifier)
- To prevery hazards, if the external flexible lead on this lamp is damaged, it must only be re- placed by the manufacturer, its service repre sentative or an equally qualified profassional.
- To prevent hazards, if an illuminant on this product is damaged, it must be replaced by the manufacturer, its service representative or on equally qualified professional
For your safety
- Install the light so it is protected from moisture, dirt and extreme heating
- Always be attentive! Always pay attention to what you are doing and use common sense. Never us use the liger if you are having difficulty concentrating or do not feel well.
- Familiarise yourself with all instructions and diasetams in Pis manual as well as with the light itsell before use
Preparation
Required tools and material
The tools and materials specified are not included. This information and these
values are non-binding and ore only provided as a reference. The nature of the
material is determined by the individual local condrions.
- Puncil/marking tool
- pole voltage tener
- Screwdriver
- Electric dil
- Dril ja 6 mm) Side cutting pliers
- Indow
Mounting the light
Important: The electrical connection must be perfamned by a qualified
elechician or a person rained in electrical installations. This person must be
familiar with the properties of the Ight and the
WARNING! RISK OF ELECTRIC SHOCKI
Prior to insh hove the fuse or switch off the circuit breaker in the fine box
(Position (0)
Model 14162305L/14162508L:
-
Use a 2-pole voltage tester to check whether the power cable is votogeése.
-
Remove the screws 2 visible at the side of the connection housing 3 and remove the mounting bracker 1 at the back
-
Use the slotted holes on the mounting bracket to mark the bores.
-
Now and the foxing holes 6mm, depth opprox. 40mm. Se supply ine. wut to damage the
-
Insart the plugs4 Into the boras
-
Fasten the mounting bracke 1 with the provided screws 5
-
Open the junction box 7.
-
Feed the moins coble (externcil) 9 through the protective tube 8.
-
Now use the lustre termined 6 to comect the connection crable for the lig the mains light comnection cable (external) 9.
Note: Be connect the individual leads a the mains connection cable (external) correctly: live wine, black or brown symbol L neutral wiro, hlaa symbol N, protective conductor/ . -
This light is classifed as protection class . The protective carth wire is not connected
-
Push the mains connection cord leictamol) 9 double insulation at least 8 mm into the protetive tube.
-
Be sure the protecthe tube8 is sected comecdly at the junction box 7
-
Close the junction box
-
Now use the screws 2 to fosten the light to the mounting bracket
-
Adjust the iramp ams 10 to the desired pesiton.
Model 14162402L:
-
Remove all packaging material
-
Place the fastening plea plote 11 on the connection housing
-
Make sure that the screw holes are in the recess provided for them. Pay attention to the correct position.
-
Push the cables of the lamp ams [10] through
-
Screw the lamp arms 10 to the fastening plate and the connection housing with he come sponding screws 12.
-
Connect the lamp arms 10 with the connecting codiles 13 in the commedion housing 3.
-
Use a 2-pole voltage to check whether the power cable is vahape-free.
-
Use the slotted holes on the mounting bracket 1 intended for the screws 5 us a guide to mark the drilling holes.
-
Naw drill the fixing holes (6mm, depth орк. 40. Be sure not to damage supply Iine.
-
Insert the plugs 4 into the bores.
-
Fasten the mounting brucker 1 with the provided screws 5.
-
Open the junction box 7.
-
Feed the mains cable extemal 9 through the protective tube 8.
-
Now use the lustre terminal to connect the connection coble for the light to the moins coo nection cable external 9.
Note: Be sure to connect the individual leads on the mains connection cable (external) corectly Bve wire, black or brown symbol l, neutral wire, blue symbol N, protective conductor/ . -
This light is classified as protection class II. The protective earth wire is not connected
-
Push the mains connection cord (external) 9 double insulation at least 8 mm into the protec five tube 8.
-
Be sure the protective tube is seated correctly the junction junction box box 7.
-
Now use the screws 2 to fasten the light the mourring bracker.
-
Close the junction box 7.
Replace the fuse or switch on the circuit breaker (I seting) in the fuse box
Your light is now ready to use.
Initial use
Use the wall switch to switch the light on or off.
Maintenance and cleaning
WARNING! RISK OF ELECTRIC SHOCK!
Disconnect the light from the mains circuit before
cleaning, To do so, remove the fuse or switch off the circuit breaker in the
fuse box 10 position).
CAUTION! RISK OF BURNS DUE TO HOT SURFACESI!
- Allow the light to cool down completely Do not use solvents, benzene or similar substances. They could damage the light.
- Only use a dry, lint-free cloth for deaning,
- Replace the fuse or switch on the circul breaker (Pasithion I) inside the fuse box.
Disposal
The packaging is mode entirely of recyclable mate rnals, which you may dispose of at local recycling facilities.
Observe the marking of the packaging materials for waste separation, which are
marked with abbreviations (a) and numbers (b) with following meaning: 1-7:
plastics/20-22: paper and 6bre board/80-98 composite menariols.
To help protect the environment, please dispose of the product properly when
it has reached the and of its useful life and not in the household waste:
Information on collection points and their opening hauns can be abtained from
your local authority.
The product ind. accessories and packaging mate rials are recyclable and are
subject to axtended producer responsibility. Dispose them separately,
following the illustrated Infotri sorting information), for better waste
meatment. The Triman logo is valid in France only
Information
Warranty
A 36 month warranty is extended for this appliance at the time of purchase.
The appliance has been manufactured with care under strict quality control.
During the warranty period any defects in material or manufacture will be
replaced free of charge. In the event of a defect during the warranty period,
please send the appliance to the service address listed, indicating the
following model number: 14162305L/14162402L/14162508L. Expendable parts (such
as bulbs) and damage caused by improper handling, failure to observe the
instructions for use or modification by unauthor- ised persons are excluded
from the warranty. The performance of services under the warranty does not
extend or renew the warranty period.
Declaration of conformity CE
This product fulfils the requirements of the applicable European and national
directives. Conformity has been demonstrated. The relevant declarations and
documents are held by the manufacturer.
Manufacturer/Service
IAN 452544_2310
Please have your receipt and item number (ΙΑΝ 452544_2310) ready as your proof
of pur- chase when enquiring about your product
Briloner Leuchten GmbH & Co. KG
Am Steinbach 14
59872 Meschede GERMANY
Tel.: +49 29 1/95 29 93-650
Fax: +49 29 1/95 29 93-109
E-Mail: kundenservice@briloner.com
www.briloner.com
Free service number:
Tel.: 00800/27456637
BRILONER LEUCHTEN GMBH & CO. KG
Am Steinbach 14 59872 Meschede GERMANY
Last Information Update.
Ident.-No.: 14162305L/14162402L/14162508L122023-8www.lidi-
service.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>