Shelly B1524 Dimmer 0/1-10V PM Gen3 User Guide
- September 19, 2024
- Shelly
Table of Contents
Shelly B1524 Dimmer 0/1-10V PM Gen3
Specifications
- Model: Shelly Dimmer 0/1-10V PM Gen3
- Input Voltage : 110-240 V~
- Control Output: 0/1-10V
- Rated Current: Max. 16A
- Operating Temperature: 0°C to 40°C
- Indoor Use Only
Legend
Device terminals
- +: 0-10 VDC positive terminal
- -: 0-10 VDC negative terminal
- O: Relay output
- S1: Switch/button input terminals for light control
- S2: Switch/button input terminals for light control
- L: Live (110-240 V) terminal
- N: Neutral terminal
- Dim+ / Dim-: Positive/negative terminal of the LED driver
- V+ / V-: Positive/negative output of the LED driver
Wires
- N: Neutral wire
- L: Live (110-240 V) wire
User and safety guide
- Shelly Dimmer 0/1-10V PM Gen3
- The smart 0/1-10V dimming controller
Safety information
For safe and proper use, read this guide, and any other documents accompanying this product. Keep them for future reference. Failure to follow the installation procedures can lead to malfunction, danger to health and life, violation of law, and/or refusal of legal and commercial guarantees (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure to follow the user and safety instructions in this guide.
WARNING: This sign indicates safety information
INFO: This sign indicates an important note.
- WARNING! Risk of electric shock. Installation of the Device to the power grid must be performed carefully by a qualified electrician.
- CAUTION! Before installing the Device, turn the circuit breakers off. Use a suitable test device to make sure there is no voltage on the wires you want to connect. When you are sure that there is no voltage, proceed to the installation.
- WARNING! Before making any changes to the connections, ensure there is no voltage present at the Device terminals.
- CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
- CAUTION! Connect the Device only to a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device can cause fire, property damage, and electric shock.
- CAUTION! The Device must be secured by a cable protection switch by EN60898-1 (tripping characteristic B or C, max. 16A rated current, min. 6 kA interrupting rating, energy limiting class 3).
- CAUTION! Do not use the Device if it shows any sign of damage or defect.
- CAUTION! The Device may be connected to and control only electric circuits and appliances that comply with the applicable standards and safety norms.
- CAUTION! The Device is intended only for indoor use.
- CAUTION! Keep the Device away from dirt and moisture.
Product Description
Shelly Dimmer 0/1-10V PM Gen3 (the De-vice) is a smart dimming controller that allows remote control of dimming drivers from a mobile phone, tablet, PC, or home automation system. It can work standalone in a local Wi-Fi network or it can also be operated through cloud home automation services. The device provides support for 0-10V and 1-10V types of drivers.
- The Device has an embedded web interface used to monitor, control, and adjust the Device. The web interface is accessible at http://192.168.33.1 when connected directly to the Device access point or at its IP address when you and the Device are connected to the same network.
- The Device can access and interact with other smart devices or automation systems if they are in the same network infrastructure. Shelly Europe Ltd. provides APIs for the devices, their integration, and cloud control. For more information, visit
https://shelly-api-docs.shelly.cloud.
INFO: The Device comes with factory-installed firmware. To keep it updated and secure, Shelly Europe Ltd. provides the latest firm-ware updates free of charge. Access the updates through either the embedded web interface or the Shelly Smart Control mobile application. Installation of firmware updates is the user’s responsibility. Shelly Europe Ltd. shall not be liable for any lack of conformity of the Device caused by the failure of the user to install the available updates in a timely manner.
Installation instructions
- To connect the Device, we recommend us-ing solid single-core wires or stranded wires with ferrules. The wires should have insula-tion with increased heat resistance, not less than PVC T105°C (221°F).
- When connecting wires to the Device termi-nals, consider the specified conductor cross section and stripped length. Do not connect multiple wires into a single terminal.
- For security reasons, after you successfully connect the Device to the local Wi-Fi network, we recommend that you disable or pass-word-protect the Device AP (Access Point).
- To perform a factory reset of the Device, press and hold the Control button for 10 seconds.
- To enable the access point and the Blue-tooth connection of the Device, press and hold the Control button for 5 seconds. Connect the Device positive output (+) to the LED driver positive input (Dim+), and the Device negative output (-) to the LED driver negative input (Dim -) as shown in Fig. 1. Connect the Live wire to the Device L termi-nal, and the Neutral wire to the N terminal and to the LED driver N terminal.
Connect the Device relay output O to the LED driver L terminal.
- Connect switches or buttons to the Device S1 and S2 terminals and the Live wire.
- The Device can work in single or dual-button modes or in a single switch mode.
- In single input mode, S2 is always detached. Connect the LED driver to the LED lights in accordance with the installation instructions provided by the LED driver manufacturer.
Specifications
- Size (HxWxD): 38.5×43.5x17mm / 1.52×1.71×0.67in
- Weight: 28.5 g / 0.99 oz
- Screw terminals max torque : 0.4 Nm / 3.5 lbin
- Conductor cross section: 0.2 to 2.5 mm² / 24 to 14 AWG (solid, stranded, and boot-lace ferrules)
- Conductor stripped length: 5 to 6 mm / 0.20 to 0.24 in
- Mounting: Wall console/behind wall/ceil-ing construction
- Shell material: Plastic
- Ambient working temperature: -20°C to 40°C / -5°F to 105°F
- Humidity: 30% to 70% RH
- Max. altitude: 2000 m / 6562 ft
- Power supply: 110-240 V~ 50/60 Hz
- Power consumption: < 1.5 W
- External protection: 16A, tripping char-acteristic B or C, 6 kA interrupting rating, energy limiting class 3
- Max. switching voltage: 240 V~
- Max. switching current: 13 A
- Max. control current: 35 mA
- Voltmeter (AC ): 110 – 240 V
- Ammeter (AC ): 50 mA – 16 A
- Meters accuracy: ±10%
- Power and energy meters:
- Active and apparent power
- Active and apparent energy
- Power factor
- Measurement data storage: No
- Internal-temperature sensor : Yes
Wi-Fi
- Protocol: 802.11 b/g/n
- RF band: 2401-2495 MHz
- Max. RF power: < 20 dBm
- Range: Up to 30 m / 100 ft indoors and up to 50 m / 160 ft outdoors (depending on local conditions)
Bluetooth
- Protocol: 4.2
- RF band : 2400-2483.5 MHz
- Max. RF power: < 4 dBm
- Range: Up to 30 m / 100 ft outdoors, up to 10 m / 33 ft indoors (depending on local conditions)
- CPU: ESP-Shelly-C38F
- Clock frequency: 40 Mhz
- Flash: 8MB
- Schedules: 20
- Webhooks (URL actions): 20 with 5 URLs per hook
- Scripting: Yes
- MQTT: Yes
- Advanced schedules: Yes
- KVS (Key-Value Store): Yes
Shelly Cloud inclusion
- The Device can be monitored, controlled, and set up through our Shelly Cloud home automation service. You can use the service through either our Android, iOS, or Harmony OS mobile application or through any internet browser at: https://control.shelly.cloud/.
- If you choose to use the Device with the application and Shelly Cloud service, you can find instructions on how to connect the Device to the Cloud and control it from the Shelly app in the application guide: https://shelly.link/app-guide.
- The Shelly mobile application and Shelly Cloud service are not conditions for the De-vice to function properly. This Device can be used standalone or with various other home automation platforms.
Troubleshooting
In case you encounter problems with the installation or operation of the Device, check its knowledge base page: https://shelly.link/dimmer_0/1-10V_PM_Gen3
Declaration of Conformity
Hereby, Shelly Europe Ltd. declares that the radio equipment type Shelly
Dimmer 0/1-10V PM Gen3 is in compliance with Direc-tive 2014/53/EU,
2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declara-tion of
conformity is available at the follow-ing internet address:
https://shelly.link/dimmer_0/1-10V_PM_Gen3_DoC
- Manufacturer: Shelly Europe Ltd.
- Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
- Tel.: +359 2 988 7435
- E-mail : support@shelly.cloud
- Official website: https://www.shelly.com Changes in contact information are pub-lished by the Manufacturer on the official website.
All rights to the trademark Shelly® and other intellectual rights associated with this Device belong to Shelly Europe Ltd.
FAQ
- Q: How can I update the firmware of the Shelly Dimmer 0/1-10V PM Gen3?
- A: You can update the firmware through the embedded web interface or the Shelly Smart Control mobile application provided by Shelly Europe Ltd.
- Q: What should I do if the Device shows signs of damage or defect?
- A: Do not use the Device and contact customer support for assistance. Using a damaged Device can be dangerous.
- Q: Can the Shelly Dimmer 0/1-10V PM Gen3 be used outdoors?
- A: No, the Device is intended for indoor use only. Keep it away from dirt and moisture to ensure proper functionality.
References
- Shelly Control
- Welcome to Shelly Technical Documentation | Shelly Technical Documentation
- Shelly Smart Control Guide
- Shelly Gen3 devices
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>