Shelly Wi-Fi Smart Plug User Guide
- October 30, 2023
- Shelly
Table of Contents
Shelly Wi-Fi Smart Plug
Read before use
This document contains important technical and safety information about the
device, its safety use and installation.
CAUTION! Before beginning the installation, please read carefully and entirely
this guide and any other documents accompanying the device. Failure to follow
the installation procedures could lead to malfunction, danger to your health
and life, violation of law or refusal of legal and/or commercial guarantee (if
any). Allterco Robotics EOOD is not responsible for any loss or damage in case
of incorrect installation or improper operation of this device due to failure
of following the user and safety instructions in this guide.
Product Introduction
Shelly® is a line of innovative microprocessor-managed devices, which allow
remote control of electric circuits through a mobile phone, tablet, PC, or
home automation system. Shelly® devices can work standalone in a local Wi-Fi
network or they can also be operated through cloud home automation services.
Shelly Cloud is a service that can be accessed using either Android or iOS
mobile application, or with any internet browser at
https://home.shelly.cloud/. Shelly® devices can be accessed, controlled and
monitored remotely from any place where the user has internet connectivity, as
long as the devices are connected to a Wi-Fi router and the Internet. Shelly®
devices have Embedded Web Interface accessible at http://192.168.33.1 when
connected directly to the device access point, or at the device IP address on
the local Wi-Fi network. The embedded Web Interface can be used to monitor and
control the device, as well as adjust its settings.
Shelly® devices can communicate directly with other Wi-Fi devices through HTTP
protocol. An API is provided by Allterco Robotics EOOD.
For more information, please visit: https://shelly-api-docs.shelly.cloud
/#shelly-family-overview. Shelly® devices are delivered with factory-
installed firmware. If firmware updates are necessary to keep the devices in
conformity, including security updates, Allterco Robotics EOOD will provide
the updates free of charge through the device Embedded Web Interface or the
Shelly mobile application, where the information about the current firmware
version is available. The choice to install or not the device firmware updates
is the user’s sole responsibility. Allterco Robotics EOOD shall not be liable
for any lack of conformity of the device caused by failure of the user to
install the provided updates in a timely manner. Shelly Plus Plug IT (The
Device) is a smart plug/outlet with power measurement and overheating
protection, which allows remote control of electric appliances through a
mobile phone, tablet, laptop, or home automation system. It can work
standalone in a local Wi-Fi network or it can also be operated through cloud
home automation services
Schematic
Legend
- A: Socket
- B: Control button with LED indication
- C: Plug
Installation Instructions
CAUTION! The product is intended for indoor use only.
**CAUTION! Protect the product from dirt and moisture! Do not use the
product in a damp environment!
CAUTION! Do not allow children to play with the device, especially with
the control button!
CAUTION! Use the Device only with a power grid and appliances which comply
with all applicable regulations. A short circuit in the power grid orany
appliance connected to the Device may damage it.
CAUTION! Do not connect the Device to appliances exceeding the given max
load!
CAUTION!** Connect the Device only in the way shown in these instructions.
Any other method could cause damage and/or injury.
Insert Shelly Plus Plug IT into a power socket without an appliance/load
connected to it.
The LED indication will start flashing with a blue light, indicating the
Device is in Access Point (AP) mode. You can access the embedded web interface
at http://192.168.33.1 in the Wi-Fi network, created by the Device
(ShellyPlugIT-XXXXXXXXXXXX) and use it to control the Device and change its
settings.
You can now plug an appliance into the Device socket.
To turn the appliance on, press briefly the control button. The LED indication
light will change to red. Press the control button again to turn the appliance
off. The LED indication will return to its previous status.
Cleaning
CAUTION! Before cleaning the Device, power off the connected appliance,
unplug it and only then unplug the Device. Never clean the Device if it is
connected to the mains!
Use a wet soft cloth to clean the Device.
CAUTION! Do not use aggressive detergents!
CAUTION! Do not immerse the Device or wash it under running water!
Disposal and recycling
This refers to the waste of electrical and electronic equipment. It is
applicable in the EU, US and other countries to collect waste separately.
This symbol on the product or in the accompanying literature indicates that
the product should not be disposed of in the daily waste.
Shelly® Plus Plug IT must be recycled to avoid possible damage to the
environment or human health from uncontrolled waste disposal and to promote
the reuse of materials and resources. It is your responsibility to dispose of
the device separately from general household waste when it is already
unusable.
Initial Inclusion
If you choose to use the Device with the Shelly Cloud mobile application and
Shelly Cloud service, instructions on how to connect the Device to the Cloud
and control it through the Shelly App can be found in the “App Guide” at
www.shelly.cloud/app-guide.
The Shelly mobile application and Shelly Cloud service are not not conditions
for the Device to function properly. This Device can be used standalone or
with various other home automation platforms and protocols.
CAUTION! Do not allow children to play with the buttons/switches
connected to the Device. Keep the devices for remote control of Shelly (mobile
phones, tablets, PCs) away from children.
LED indication
- Blue flashing quickly: AP Mode
- Blue flashing slowly: Connected to a Wi-Fi network
- Blue still: Connected to Shelly Cloud
- Red still: Power supplied to the plugged appliance
- Red flashing slowly: Reboot initiated (Power button pressed and held for 5 sec.)
- Red flashing quickly: Factory reset initiated (Power button pressed and held for 10 sec.)
- Red and Blue flashing alternately: Firmware update
Control button
- Press to turn on/off the plugged appliance.
- Press and hold for 5 sec to activate Device AP
- Press and hold for 10 sec to factory reset
Specification
- Dimensions (HxWxD): 70x70x70 mm
- Weight: 105 g
- Compatible sockets: CEI 23-16 / IT1-10P (Type L)
- Compatible plugs: CEI 23-16 / IT1-10P (Type L), CEE 7/16 (Type C)
- Ambient temperature: from -20 °C to 40 °C
- Humidity 30 % to 70 % RH
- Max. altitude 2000 m
- Power supply: 230 V AC ±10 % , 50/60 Hz
- Electrical consumption: < 1 W
- Max. current: 10 A
- Max. power: 2300 W (resistive load only)
- Overheating protection: Yes
- Overload protection: Yes
- Power measurement: Yes
- RF band: 2401 – 2495 MHz
- Max. RF power: < 20 dBm
- Wi-Fi protocol: 802.11 b/g/n
- Wi-Fi operational range (depending on local conditions):
- up to 50 m / 160 ft outdoors
- up to 30 m / 100 ft indoors
- Bluetooth protocol: 4.2
- Bluetooth operational range (depending on local conditions):
- up to 30 m / 100 ft outdoors
- up to 10 m / 33 ft indoors
- CPU: ESP32
- Flash: 4 MB
- Schedules: 20
- Webhooks (URL actions): 20 with 5 URLs per hook
- Scripting: mJS
- MQTT: Yes
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
Plus Plug IT is in compliance with Directive 2014/53/EU, 2014/35/ EU,
2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is
available at the following internet address:
https://shelly.link/plus-plug-it-DoC
Manufacturer: Allterco Robotics EOOD
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Official website: https://www.shelly.cloud
Changes in the contact information data are published by the Manufacturer on
the official website. https://www.shelly.cloud
All rights to the trademark Shelly® and other intellectual rights associated
with this Device belong to Allterco Robotics EOOD.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>