Wallprotex WX1 Clear Poly Car Bonate Corner Guards Instructions

Wallprotex WX1 Clear Poly Car Bonate Corner Guards

Product Specifications

• Product Name: Clear Polycarbonate Corner Guards
• Model: WX1
• Material: Polycarbonate
• Installation Options: With Holes and Screws or Nails, With Double Sided Tape

Corner Guards with Holes and Screws or Nails

STEP 1
Wall surfaces must be clean, dry, and free from dust and grease. Wipe the wall surface with a solvent to ensure all grease, dust, and dirt are removed. Make sure that the cleaning solvent used will not damage the finish on the wall surface.

STEP 2
Remove the clear protective film on the exposed side of the corner guard.

STEP 3
3/4” WING
Place in the desired location and hold the corner guard firmly. Using factory- supplied nails, hammer the nail through the corner guard into the wall.

1-1/8”-3” WING
Place in the desired location and hold the corner guard firmly. Attach the corner guard by placing the provided self-tapping screws in the pre-drilled counter sunk holes and attach to the wall.

Corner Guards with Double Sided Tape

STEP 1
Wall surfaces must be clean, dry, and free from dust and grease. Wipe the wall surface with a solvent to ensure all grease, dust, and dirt are removed. Make sure that the cleaning solvent used will not damage the finish on the wall surface.

STEP 2
Remove the clear protective film on the exposed side of the corner guard (clear corner guards only).  Self-adhesive corner guards are easy to install but will break down in high trac areas more quickly than a corner guard that is fastened with holes and screws.

STEP 3
Peel o backing tape from one wing entirely, then peel back the tape partially on on the second wing. Place the wing with the fully exposed tape to the wall, then remove the remainder of the tape backing from the second wing. Press firmly along the entire length of the corner protector to ensure a good bond.

Cutting Polycarbonate

Due to the tough nature of polycarbonate corner guards, Wallprotex does not recommend cutting the corner guards in the field. The corner guard material when cut with a power saw can cause the saw to kick back and injure the operator. For custom lengths
call before placing an order and Wallprotex can cut the parts to size in the manufacturing process. If cutting is required, use a hacksaw and be careful.

Storage & Handling
The corner guards are shipped unassembled. Upon receipt, the corner guards should be stored in the horizontal position at room temperature (65 °-75 ° F). This is a finished product; store in a protected, clean, and dry area away from direct sunlight.

Cleaning Instructions

STEP 1
For best results, the use of liquid cleaners such as “409,” “Fantastic,” and “Mr. Clean,” etc. are recommended. The use of powder cleansers is not recommended. The use of such cleansers can leave a residue that is difficult to remove.

STEP 2
Do not use chlorinated or aromatic hydrocarbons, esters, or ketones to clean Wallpro- tex vinyl products. Avoid the use of heavy degreasers, compounds containing surfactants, and abrasive compounds or cleaning devices.

Caution

• DO NOT walk on the corner guards.
• DO NOT store anything on top of the corner guards.

Frequently Asked Questions

Q: Can I cut the corner guards to a custom length?
A: It is not recommended to cut the corner guards in the field due to safety reasons. Contact the manufacturer for custom lengths.

Q: What cleaners should I use to clean the corner guards?
A: Liquid cleaners like 409, Fantastic, or Mr. Clean are recommended. Avoid powder cleansers as they can leave residue.

785 Oakwood Road
Suite C-100
Lake Zurich, IL 60047-1524

info@kofflersales.com
www.KofflerSales.com
1-847-438-1152

References

• Koffler Sales Company

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>