Stylish MODENA K-131 Kitchen Faucet Installation Guide

: September 18, 2024
: Stylish

Table of Contents

Stylish MODENA K-131 Kitchen Faucet
MODENA K-131 KITCHEN FAUCET
SOAP DISPENSER
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Stylish MODENA K-131 Kitchen Faucet

MODENA K-131 KITCHEN FAUCET

BEFORE YOU BEGIN YOUR INSTALLATION

FAUCET INSTALLATION

Ensure there is a 035mm through-hole on the kitchen counter. Remove the mounting nut (A) and washer (B) from the threaded shroud (C).
Connect the braided supply hoses to the faucet, tighten gently with a wrench,
Position the faucet on the installation surface. Fit flexible hoses through holes on the countertop or sink, Slide the washer and thread the mounting nut onto the threaded shroud, Turn the faucet to desired handle position, and Securely tighten clamp screws (E)
Connect pullout hose to quick connect and insert weight (loose install)
Secure weight on the lowest vertical point on the pull-out hose side, (not on the quick connect side)
Before connecting the supply hose, flush the supply valves to clear any debris. Place a bucket underneath valves and run water for 5 to l 0 seconds. Turn the water off.
Connect hot and cold water lines to the inlet pipe and tighten with a wrench until snug, Do not over-tight.
Unscrew the spray head by hand. Hold the tip of the spray hose down turn on the faucet and let the water run for 60 seconds to flush any debris, then the re-connect spray head. Ensure the gasket is present.

CARE AND CLEANING

Clean the faucet frequently using mild soap or an non-abrasive cleaner and then quickly rinse with water and dry with a soft cloth only,
Using abrasive cleaners, solvents, acid cleaners, or any scrubbing detergent, polisher, or scraper will damage the finish and void the warranty.

WARRANTY
For additional technical assistance or any questions or concerns about your faucet’s warranty, please contact us

SOAP DISPENSER

S-01
BEFORE YOU BEGIN YOUR INSTALLATION

WARRANTY
For additional technical assistance or for any questions or concerns about your soap dispnsers warranty, please contact US.

INSTALLATION STEPS

Recommend hole size 25mm to 29mm hole diameter.
Detach the body tank from the faucet and also remove the hexagon nut.
Introduce the connector rod into the hole, and ensure the flange and plastic rubber are above the countertop. Secure the connector rod with a hexagon nut, firmly with a wrench.
Hand secure body tank to connector rod.
Now dispenser can be filled with soap from the top, then a straw can be inserted into the soap dispenser.
To dispense soap, push down on the spout. Use hand palm to push down and get soap pumped.

CARE AND CLEANING
Many times the pump itself or the end of the nozzle can get clogged with hard soap particles, dirt, or other buildup. Following some very simple steps, you can get your dispenser working properly.

Check the tube that is connected to the pump lever (the part you push down on for the soap to be dispensed) to be sure that the tubing is cleared of any debris. Look to see if there are any hard particles or buildup within the tube.
Turn the tube upside down so that the pump part is upside down and the opening of the tube is toward the ceiling. Run the tube under hot water for 2 to 3 minutes, allowing any buildup inside the tube to be flushed out. Also, run the pump dispenser (where the soap comes out) under the hot water as well.
Place the small pipe cleaner inside the tube and run it in both a circular motion and up and down several times within the tube to help clean it out. Also, take the pipe cleaner into the pump dispenser hole to be sure it is clear of any debris.
With a sharp object such as a safety pin, gently clean out the tip of the nozzle of all hardened soap.

Using abrasive cleaners, solvents, acid cleaners, or any scrubbing detergent, polisher, or scraper will damage the finish and void the warranty.

Stylish International Inc. Follow us on Instagram! Check out and let us know your comments stylishly. International.inc

Products and specifications shown are subject to change without notice. Please contact our technical support at care@stylishkb.com for any further queries, replacement parts requests, etc. ©2019 Stylish® all rights reserved