OLIGHT Baldr-S L70903784 800-Lumens USB Rechargeable Flashlight User Manual

: September 18, 2024
: OLIGHT

Table of Contents

OLIGHT Baldr-S L70903784 800-Lumens USB Rechargeable Flashlight
IN THE BOX
SPECIFICATIONS
PRODUCT OVERVIEW
BEFORE FIRST USE
LIGHT INSTALLATION
OPERATION
WARRANTY
FAQs
Video-OLIGHT Baldr-S L70903784 800-Lumens USB Rechargeable Flashlight
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OLIGHT Baldr-S L70903784 800-Lumens USB Rechargeable Flashlight

Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!

IN THE BOX

BALDR S ( With Battery )
USB Magnetic Charging Cable
Allen Wrench
1913 Adapter and Screws
NYLOK Oval Point Set Screw
NYLOK Cone Point Set Screw
M3x4 Socket Screws

SPECIFICATIONS

GREEN BEAM OFF

GREEN BEAM ON

The green beam level is Class 3R, obeying the standard IEC60825-1 requirement.
All above specifications are test results based on ANSI/NEMA FL1 Standard. The tests are performed when the built-in battery is fully charged.

PRODUCT OVERVIEW

BEFORE FIRST USE

The low battery indicator will turn red when the light is working and the battery level is less than 10%.
Connect the USB end of the charging cable to an external USB power source, then attach the other end of the magnetic charging cable to the charging port of the light. It takes no more than 1 hour to fully charge the light ( For reference only. When the USB power supply is insufficient to provide 5V 0.35A power capacity, the charging time will be longer ).
Before first use please fully charge the product.

LIGHT INSTALLATION

Pull open the swing arm.
Slide the rail mount to your desired position
Use the included Allen wrench to ensure that the two socket screws are tight. (Two backup socket screws are included)
Position the Glock rail adapter (already installed) or Picatinny rail adapter (to be installed first) to the desired rail notch and then close the swing arm.

ICON LIGHT SETTING

LIGHT

LIGHT&GREEN BEAM

GREEN BEAM

COMPATIBILITY CHECK:
The BALDR S can be used on most Glock or Picatinny (mil-std-1913) type rails. The Glock adapter labeled “GL” is already installed and a Picatinny (mil- std-1913) adapter is included in the package. To install the light on Picatinny (mil-std-1913) rails, the user needs to replace the “GL” adapter with the included 1913 adapter using the screws and wrench provided in the package.

GREEN BEAM CALIBRATION:
Use the included hex wrench to rotate the adjustment screws on the side of the light to calibrate the vertical or horizontal angle of the green beam, and finally sight in the green beam for accurate use.

NOTE:

A backup set of NYLOK adjustable screws is included.
The NYLOK cone point set screw is used for vertical angle calibration.
The NYLOK oval point set screw is used for horizontal angle calibration.

DANGER

DO NOT throw the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
DO NOT charge this product with other charging cables except the one included in the original package.
DO NOT cover the light head, or place the light head down on the ground when the light is on. The radiation energy of the light may cause damage to the light itself, or even result in burning to other materials.
DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature.

WARNING

Keep out of reach of children.
Green beam light is bright and blinding – DO NOT shine at aircraft or vehicles at any distance.
If the light is stored for a long time or transported, please turn the light setting switch to the Green Beam Only position.

NOTICE

The setting switch is magnetically sensitive, when close to magnet, interference may occur.
Fully charge the battery before storing the light for a long period of time.
Please keep the charging port clean. Wipe any dust off beforecharging.
lease wipe the lens regularly. If the green beam spot is abnormal, please wipe and clean the lens
The LED light will work for one minute at the top output mode and gradually step down to 300 lumens within 2 minutes.
The two switches can only be activated by pushing downward. Pushing forward or on the side of the switch will not activate the light.
Always attach the light on the rail could better protect the switch and avoid damage caused by falling.
The BALDR S can only be charged with the included MCC special charging cable, not compatible with other MCC cables.
NYLOK is a registered trademark of NYLOK LLC.

EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.

OPERATION

THREE LIGHT SETTINGS AVAILABLE: As the mark shows, push the setting switch from left, middle, right to select green beam only, white LED/green beam combined, white LED only accordingly.
The ambidextrous switch on the BALDR S can only be pressed down to activate the light. Pressing the side or front of the switch will not turn it on.
MOMENTARY ON: Press and hold down either switch for momentary on. The light will stay on until the switch is released.
ON/OFF: Single click either switch for constant on. Single click again to turn the light off. When the mode switch is positioned to white LED only or white LED/green beam combined mode, the followingoperations are effective:
CHANGE BRIGHTNESS: When the light is on quickly click either side of the tail switch twice to change between high white light and low white light. When the light is turned on again, it will return to the previously used brightness level.
HIGH WHITE LIGHT: When the light is off, quickly click either side of the tail switch twice to access the high white light directly HIGH en LOW light.

USA Customer Support:cs@olightstore.com
Global Customer Support:customer-service@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.

WARRANTY

Within 30 days of purchase: Contact the original seller for repair or replacement.
Within 2 years of purchase: Contact Olight for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.

Dongguan Olight E-Commerce Technology Co., Ltd
Address: 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.
Made in China

EU-Declaration of Conformity can be found here CE: https://olightworld.com /ec-declaration