CARBONE G8x M3 M4 Carbon Fiber Front Splitter Installation Guide
- September 18, 2024
- Carbone
Table of Contents
G8x M3 M4 Carbon Fiber Front Splitter
“`html
Product Information:
Specifications:
-
Product: G8x M3 M4 Carbon Fiber Front Lip Spoiler
-
Compatibility: BMW M3 Standard 2021+, BMW M3 Competition 2021+,
BMW M3 CSL 2023+, BMW M4 Standard 2021+, BMW M4 Competition 2021+,
BMW M4 CSL 2023+ -
Components:
- x1 3-piece Carbon Fiber Front Lip
- x10 Mounting Screws
- x2 Rubber Washers
-
Tools Required: Socket wrench or power tool
Product Usage Instructions:
Prep:
-
Ensure that your G8X M3/M4’s front bumper has been thoroughly
cleaned using a microfiber cloth and isopropyl alcohol or a gentle
cleaning solution. -
Align the three pieces of the carbon fiber front lip before
installation using the provided double-sided tape to attach them
securely together.
Installation:
-
Remove the 8mm factory bolts securing the front section of the
bumper and the push pins securing the side plastic bumper covers
without removing the side covers. -
Align the carbon fiber front lip symmetrically and start by
placing back the factory push pins securing the sides. -
Place the provided rubber washers between the bumper and the
front lip at specified locations. -
Position the middle carbon fiber lip section aligning it with
pre-drilled holes, remove the backing from the double-sided tape,
and press it firmly onto the bumper. -
Align the provided screws to the pre-drilled holes and tighten
using a socket wrench or power tool.
Frequently Asked Questions (FAQ):
Q: Is professional installation required for this product?
A: Yes, professional installation is recommended for optimal
fitment and performance. However, experienced DIY enthusiasts may
also attempt installation with necessary tools and expertise.
Q: What models is this product compatible with?
A: This product is compatible with BMW M3 Standard 2021+, BMW M3
Competition 2021+, BMW M3 CSL 2023+, BMW M4 Standard 2021+, BMW M4
Competition 2021+, and BMW M4 CSL 2023+.
“`
G8x M3 M4 Carbon Fiber Front Lip Spoiler
Installation Guide
Professional Installation Required For optimal fitment and performance, we
recommend professional installation. While experienced DIY enthusiasts may
successfully complete the installation, ensuring precise alignment and secure
attachment is crucial. Professional installation not only enhances the
aesthetic appeal but also minimizes the risk of improper fitment or damage. If
you choose to install it yourself, please ensure you have the necessary tools
and expertise.
Compatible with
BMW M3 Standard 2021+ BMW M3 Competition 2021+ BMW M3 CSL 2023+
BMW M4 Standard 2021+ BMW M4 Competition 2021+ BMW M4 CSL 2023+
www.CarboneUS.com
1
Components
x1
x10
x2
3-piece Carbon Fiber Front Lip
Mounting Screws
Rubber Washers
*COMPATIBLE ONLY WITH THE OEM BMW G8X M3 M4 FRONT BUMPER
Tools Required:
· Socket Wrench · 8mm Socket · Pry Tool/ Flat Head Screwdriver · Phillips
Screwdriver
Prep
1. Ensure that your G8X M3/M4’s front bumper has been thoroughly cleaned. Use
a microfiber cloth and isopropyl alcohol or a gentle cleaning solution to
clean the bottom surface of the front bumper thoroughly.
Clean here
2. Before installation, align the three pieces of the carbon fiber front lip
to ensure a precise fit. Use the provided double-sided tape to securely attach
the pieces together. Take care to align each piece carefully to avoid any
gaps.
www.CarboneUS.com
*Professional installation recommended
2
Install
1. Remove the 8mm factory bolts securing the front section of the bumper, and
the push pins securing the side plastic bumper covers as shown below and store
them in a safe place for later use. *Do not remove the side covers, as our
front lip is designed to cover them.
Factory bolts
2. Align your Carbone’s carbon fiber front lip so that it is perfectly
symmetrical.
3. Start by placing back the factory push pins securing the sides.
www.CarboneUS.com
*Professional installation recommended
3
4. Place the provided rubber washers between the bumper and the carbon fiber front lip in the locations shown below.
5. Position the middle carbon fiber lip section, aligning it with the pre- drilled holes. Carefully remove the backing from the double sided tape on the center middle section and press it firmly onto the bumper.
6. Align the provided screws to the pre-drilled holes and tighten using a
socket wrench or power tool.
10x provided Screws
www.CarboneUS.com
*Professional installation recommended
4
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>