K1 Intelligent Toilet

“`html

Product Information

Specifications

• Product Name: Intelligent Toilet
• Model: K1
• Category: Convenience, Safety
• Functions:
  • Female Washing Hip Cleaning
  • Massage Washing
  • Moving Washing
  • Self-cleaning nozzle
  • One key stop
  • Position Adjustment
  • Water heated instantly

Product Usage Instructions

Warnings and Safety

It is important to follow these safety precautions when using
the Intelligent Toilet:

• Read all instructions before using.
• Avoid using the product while bathing.
• Avoid placing the product where it can fall into water.

Installation

Before installing and using the Intelligent Toilet, make sure
to:

• Read the installation instructions thoroughly.
• Ensure proper grounding as described in the manual.

Maintenance

To keep your Intelligent Toilet functioning properly, follow
these maintenance tips:

• Regularly clean the surface of the toilet.
• Perform nozzle maintenance as recommended.

Troubleshooting

If you encounter any issues with the Intelligent Toilet, refer
to the troubleshooting section of the manual for guidance on:

• Power button usage.
• Wash functions troubleshooting.

FAQ

Q: How do I adjust the water temperature?

A: You can adjust the water temperature using the water
temperature adjustment feature on the toilet unit or remote
control.

Q: Is the toilet seat heated?

A: Yes, the toilet seat has a seat heating function that can be
adjusted to your desired level of warmth.

“`

Smart Toilet
Product User Manual
Product Name: Intelligent Toilet
Model: K1
Thank you for purchasing our product . Please read this manual before installation and use to ensure that your product will function at peak performance . Read this manual thoroughly and store in a safe place for future references .

IMPORTANT SAFEGUARDS
When using electrical products ,especially when children are present , basic safety precautions should always be followed , including the following
READ ALL INSTRUCTIONS BEFORE USING
DANGER – To reduce the risk of electrocution
1.Do not use while bathing 2.Do not place or store product where it can fall or be pulled into a tub or sink 3.Do not place in or drop into water or other liquid 4.Do not reach for a product that has fallen into water . Unplug immediately
WARNING- To reduce the risk of burns , electrocution ,fire or injury to persons
1.Close supervision is necessary when this product is used by ,on ,or near children or invalids 2.Use this product only for its intended use as described in this manual . Do not use attachments not recommended by the manufacturer. 3.Never operate this product if it has a damaged cord or plug , if it is not working properly , if it has been dropped or damaged , or dropped into water . Return the product to a service center for examination and repair . 4.Keep the cord away from heated surfaces 5.Never block the air openings of the product or place it on a soft surface , such as a bed or couch ,where the air openings may be blocked. Keep the air openings free of lint, hair , and the like. 6.Never use while sleeping or drowsy 7.Never drop or insert any object into any opening or hose 8.Do not use outdoors or operate where aerosol(spray)products are being used or where oxygen is being administered 9.Connect this product to a properly grounded outlet only . See grounding Instructions 10.Do not use while bathing 11.Risk of Electric shock. Connect only to a grounding type receptacle protected by a ground-fault circuit- interrupter(GFCI) 12.CAUTION- Risk of electric shock , do not remove cover (or back).Refer servicing to qualified service personnel .

SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product should be grounded . In the event of an electrical short circuit , grounding reduces the risk of electric shock by providing an escape wire for the electric current . This product is equipped with a cord having a grounding wire with a grounding plug . This plug must be plugged into an outlet that is properly installed and grounded .
DANGER-Improper use of the grounding plug can result in a risk of electric shock
If repair or replacement of the cord or plug is necessary ,do not connect the grounding wire to either flat blade terminal . The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood , or if in doubt as to whether the product is properly grounded .

The functions may vary from different part no

Category
Convenience
Safety

Functions
Female Washing Hip Cleaning
Massage Washing Moving Washing Self-cleaning nozzle
One key stop Position Adjustment Water heated instantly
Seat Induction Seat Heating Warm air drying Wind temperature adjustment Water temperature adjustment Water pressure adjustment Automatic flushing Flush during power failure Mute slow down
Night light Leakage protection
Energy saving Double filtration One key side knob Anti-fouling glaze Flame retardant material 12V safety voltage Remote control Anti bacterium seating Digital desplay screen Foot sensor flushing Decorated light
Baby mode Foot sensor open seat Foot sensor open cover
Auto open cover Baby seating

User Friendly design
New features to offer you an enjoyable experience

Contents
Parts information ——- 1 Overview ————- 2 Rotated switch ——— 1 Remote control ——– 2 Warnings and safety —– 1 Warming ————- 2 Attention ————- 1
Installation ———— 1 Before you install ——- 2 Installing your product —- 1 Function explanations —- 2 Maintenance ———- 1 Surface cleaning ——- 2 Nozzle maintenance —– 1
Troubleshooting ——– 1 Power button ———- 2 Wash functions ——– 1 Dryer ————— 2 Heated seat ———- 1 Remote control ——– 2 Toilet unit ———— 1 Soft-closing feature —– 1 Specifications ——— 2

Smart Toilet Part Information
Rotated Switch Warm Dryer Cleaner(Hip & Female wash) The heating seat
Toilet

Caution Label

Lid Power plug

D N15

Pressure stabilizing valve
D N20 T-valve
Water valve

Hose

Rotated Switch

Female washing

Hip Cleaning

Remote control
FCC ID: 2BH90-MIJIC This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) this device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.

/
Power/Stop

Hip Cleaning

Female washing

Flush

Nozzle adjustment Adjustment

Open cover Open seat Self-cleaning

Baby wash

Night light Warm air drying

Water

Seat

Wind

temperature temperature temperature

Power/Stop
You can stop the “Hip cleaning’ “Female cleaning”, “brying”and other operaation when operation

Hip Cleaning
Press this button when you are seated, the Hip wash cleaning nozzle will spray at the fixed position for 2 minutes and then stop spraying automatically.

Female washing
Press this button when you are seated, the female cleaning, nozzle will spray at the fixed position for 2 minutes and then stop spraying automatically.

Warm air drying
Press this button to start drying when you are seated. Warm air drying will stop automatically affer 3 minutes.

Adjustment
Press this button during the “hip” or. “female” cleaning and adjust the nozzle position without the use of the removable cleaning function.

Nozzle adjustment
It can increase or decrease the force of cleaning water pressure. It can be set to weak, medium, strong, or strongest.

Flush
Press this button and will start flushing.
Water temperature
4 degrees can adjust the water tempature , the tempature can be set as, one degree : the enviroment tempature, second degree : about 34°C, Third degree : about 37°C, Forth degree : about 40°C

Open cover
Press this button, the seat cover will open automatically, and then press it again, the seat cover will close automatically.(For automatic open seat cover configuration)

Open seat
Press this button, the seat opens automatically, and press again to close the seat automatically. (For automatic open seat cover configuration)

Seat temperature
4 degrees can adjust the seat tempature the tempature can be set as,one degree : the enviroment tempature, second degree : about 34°C, Third degree : about 37°C, Forth degree : about 40°C.

Wind temperature
4 degrees can adjust the wind tempature the tempature can be set as , one degree: the enviroment tempature, second degree:about 35°C, Third degree :about 45°C, Forth degree : about 55°C.

Baby wash
After the baby is seated then press the baby wash button ,it will start the hip cleaning automaticly , and the washing pressure will be adjust to the lowest level automaticly ,it will change to mobile cleaning when press one more time , and auto close the baby washing when you press the ” stop ” button

Self-cleaning
Nozzle extended and water out for nozzle washing

Night light
The night light can be turned on or off in the power-on state.

Remote control pairing
Switch the knob to the hip cleaning for about 3 seconds ,when you hear a sound , press any button of the remote ,then can pair the remote to the toilet .

Warnings and Safety
Please read thoroughly
First of all, thank you for purchasing our product, To ensure proper and safe use of thisproduct, carefully read this section prior to any usage. Afterwards, store this manual ina safe place for any needed future reference. The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be heldiable for any injuries to the user and damages to the product due to improper usageand/or failure to heed safety warnings.
Explanation of Terms and Symbols
Warning–Indicates possible injury resulting from improper usage due to negligence of this sign. Attention–Indicates human injury or property loss that may result inimproper usage due to negligence of this sign.
Note When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions
Prohibits any individual from performing any action with this symbol
Prohibits any individual from dismantling product
Keep product away from any wet environments, including , but is not limited to, humid environments, close proximities to baths, showers or sinks
Do not touch!
Do not touch with a wet hand !
Keep away from any extreme heat or fire
Operate only as instructed
Pull out the power plug !
Protective grounding

This product needs to be properly grounded Risk of electric shock If unsure , contact an electrician of Electrical installation company
Do not place a lit cigarette along with other burning abjuects into the unit. Risk of fire
Do not touch ,insert or pull out the power plug with a wet hand . Risk of electric shock
The power socket in use should be whithin the specified range (AC120V). Risk of fire and/or electric shock
Do not pull , damage , bend , twist , stretch,roll,bundle ,clamp or squeeze the power cable .Do not place anything on power cable Risk of fire and /or electric shock
If the power cord is damaged , to prevent any injuries or accidents , it should be replaced by a professional . *Risk of fire and /or electric shock

Warning
Do not use a power socket in poor condition or a damaged power plug Risk of fire and /or electric shock
Do not use during thunderstorms (pull out the power plug during storms ). Failure in doing so may lead to injury or fault in the product
When the seat ring or the cover plate is damaged , to avoid any harm, be sure to pull off the power plug , close the water source and contact your local distributor for replacement Risk of fire or electric shock
Periodically unplug the power plug and wipe off any dust from the power plug with a clean, dry cloth. Fire risk
Any person with a disability , the elderly , and children , should be using this product with the supervision of another individual Be advised that sitting on the heated seat for an extended amount of time may result in burns
This product is not a toy ,Advise children not to play with product. Risk of injury
Do not dismantle , repair or alter this product on your own .Call in a professional , or contact Dyconn Faucet for further advice . *Risk of fire , eletric shock, and/or other accident that may lead to injury.

Warning

For cleaning or maintenance of plastic parts , do not use any harsh cleaning agents .(These include ,but are not limited to products such as :concentrated sulfuric acid , concentrated nitric acid , glacial acetic acid,carbon tetrachloride, chloroform,acetone ,butanone, benzene , methylbenzene,phenol , methylphenol, dimethylformamide,methyl ether, soybean oil, acetate, 40% nitric acid ,thick salt acid ,95% alcohol, gasoline, kerosene or brake oil, etc. *Risk of damaging parts that can lead to accidents and injuries

Do not use polluted water or water meant for industrial . Risk of urocystitis or dermatitis Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.
Do not apply any force to the unit’s seat and lid .Do not stand on the lid or open or close the lid and seat forcefully . *This may result in product damage and/or user injury .

Do not install product in a humid environment or a soak room . Do not spray or soak this product with any form of liquid to prevent any damage to the product. *Risk of fire and/or electric shock .

Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use *Risk of fire , electric shock , and /or other accident that may lead to user injury

Do not spray urine at the dryer tarp. Risk of electric shock
Read the following for proper battery usage -Properly install the battery according to its correct polarity -Remove the battery during long periods without use -Replace the battery before it reaches the end of its usage . Failure to do so may result in interrupted control signals -Cover the battery with tape before disposal This will prevent battery fluid leaks that may cause fire and/or other damages.

Warning
Place the battery out of children and infant reach If battery is swallowed , contact a doctor immediately If battery fluid leaks onto user , quickly rinse off area using water If battery fluid gets into eyes , don not rub your eyes .Qucikly rinse it with water and consult a doctor immediately May result in vision impairement or blindness
When the battery is in use ,do not do the following operations Do not hold or store with metal objects (such as a necklace or a watch) Do not mix new and old batteries Do not pull battery apart battery or throw it into water and/or fire .Battery fluids may cause a fire

Attention

Do not use the heated seat or warm dryer temperature for an extended amount of time. Extended use may result in burns
While using this product, make sure that the skin is in contact with the seat sensor area. Otherwise , product may not operate correctly . Children and smaller individuals may have trouble staying in contact with sensor area.
Do not spray urine in the direction of the bidet nozzle. Doing so may result in blockage to the bidet nozzles and cleaning area.
Do not use your old hose component. Use the one provided with your product . Anything else connected to the older hose may need to be replaced. Risk of water leakage and /or property loss /damage.
In case of sudden power failure , remove the power plug and close the angle valve to prevent water leakage Risk of water leakage and/or property loss /damage.

Avoid direct sunlight or heat. Risk of product discoloration.
Do not supply electricity with an external switch. Le: connecting the universal part to a timer switch . Run the risk of issues caused by improperly resetting the thermal breaker .
When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed, be sure to fasten it with force. Risk of water leak
Pull out the power plug when the product is in disuse for and extended amount of time .Make sure to shut off the water and remove the water inside the product. Risk of fire, leaks ,and product damage .
When storing or transporting in cold climate, make sure to remove all water from the unit. Product may crack and other damages may occur due to freezing water. *Risk of fire , leaks,and product damage .

Intelligent Toilet Installation
Tools required for installation

Item list (confirm that all below items are inside the box)

Please confirm all the aforementioned items are inside the package. If there are any omissions ,please contact our customer servise .

The following are to be purchased by consumers themselves

9Volt

1.5Volt

DN20

DN15

Before you install
Water pressure check , dimensional drawing

Confirmation of water pressure The minimum dynamic operating water pressure is 35 psi , and the maximum static water pressure is 108 psi.
Determination method for minimum water flow

(Tools:stopwatch , measuring cup.)

Open the angle valve for water supply . Ensuring a flow of water at least 10.57 GPF/min.
If the above conditions cannot be met , the best flushing effect cannot be achieved and an additional booster pump is required to increase the pressure

Confirm dimensions of product with installation space

Wall

Unit:mm
400

495

700

Drain hole distance12inch
Side profile

Front view

Top view

Installing your product
Install your unit using the following steps
1 Open the box right side up
Remove the accessories frist , then remove the unit from the top , as shown in the diagrams below.
Mark your drainage hole with a cross
Cardboard installation -Align cardboard with the centerline of drain outlet -Draw contour line according to cardboard
Mounting bracket installation
Assemble the mounting bracket with bolts and then install them to the pre- installed flange plate on the ground and lock tight with nuts.

Install the ceramic body , water supply hose , T-valve

1,Place the wax ring on the drain hole at the bottom of the ceramic
2.Install sealing flange into drain outlet 3.Install ceramic toilet on corresponding position according to contour line

4.Attach the flush water hose to the T-valve and tighten

Clean water hose
T-valve Water supply

Pressure stabilizing valve

5.Attach the flush water hose to the T-valve and tighten

Flushing water hose

Tips:The toilet is heavy , and it needs to open the seat cover to carry it by two people .

T-valve Water supply

Pressure stabilizing valve
Clean water hose

6.Connect the T-valve to the water supply and tighten. Use gasket to prevent water leakage

T-valve Water supply

Pressure stabilizing valve

7.Finish installation.

Installing the remote
1.Drill two 6mm (0.24inch)diameter holes on the wall(about 1.77 in deep) 2.Knock the anchors into the hole with a hammer 3.Secure the holder with anchors 4.Use the screws to secure the holder to the wall 5.Remove the battery cover from the backside of the remote to install batteries 6.Once finished,remote is ready to be placed in its holder Detailed steps shown in the diagram below: -Please use proper mounting tools for special wall surfaces (such as wood ,HDFetc.) -The remote control holder should be installed away from the bidet’s spray trajectory -The remote control holder should be installed within reach when seated on unit. -Make sure there is nothing to block the transmission between the toilet and its remote .

Installing and replacing the battery box

Install and replace the emergency flushing battery

When delivered from the factory, the battery has been installed in the battery box.

1. Find the backup battery box behind the toilet 2. Open the backup battery box 3. Install the 9V square battery in the correct direction 4. Replace the battery box cover

Spare Battery

Please confirm the battery’s positive and negative poles .Please do not charge , disassemble, fire the battery ,or mix with used batteries or different kinds of batteries to avoid liquid leakage or explosion. The battery box has a moisture-proof function.Please ensure that the set screws are screwed in place to achieve a good seal effect. *If the battery needs to be replaced . It is recommended to contact your local dealer to have it replaced by specialized personnel.

Testing water flow
1.Open the water supply angle valve to maximumas shown in the figure.
2.Confirm various connecting parts are not watereaking. *In case of water leaking, unfasten the nuts againand install them again.

Connecting power

1.Connect to the grounding. 2.Plug in AC 120V power plug. 3.Check to see if the power is on.

(1) Check to see if the power lightis on. If not, push the resetbutton. (2)Once the power light is onthe toilet will run its initialdiagnostice: ights will turn on.cleaning nozzle will extend,the motor will begin to runand water will run through thesystem. Once the light is off, the self-diagnostic is complete. (3)Powered on: Press and holdthe knob for 3 seconds to enterthe standby mode.

Testing the product

Test whether the functions of the buttons on the remote controller and the knobs on the side of the body are normalAre all the functions working properly
Rear Wash, Front Wash (Including water pressure & nozzle position adjustment)Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleading, Anion Deodorization,Remote control. All functions listed above should be tested.

Occupied sensor point

Checking Rear Wash
Please use your hand to hold the seat sensor area, turn the knob forward orpress the “Rear Wash” button on the remote controller, and use your hand tocover the front of the washer to block the flow of wash water to avoid spraying water on your body or clothing.

Matching your remote control code
When the product leaves the factory, the remote control and the product are connected, if theremote control went failure, please re-connect the code as following methods.

1.Unplug the product’s plug, press the stop ket for few seconds until the level light is flickered.

2.Plug the attaching plug when the remote control get closer to the product.

3.The level light stops flickering and then it is lighted on.
4.At the time, the remote control and product is re-connected.

Function Explanations
Power / Stop
Stand by: Press it for 3s to activate it. Activated : under the hip cleaning , female washing, drying mode, press it for short time to stop it . Activated and not sitting on the seat ,press it for short time to flush , press it for 3s to enter to the standby mode .

Female washing

Hip Cleaning

Front wash
Under no cleaning and drying mode , and seating the toilet
Rotate backward by 45 ° to enter the women’s washing mode, which defaults to the static cleaning mode, Rotate in this direction again to switch to mobile cleaning mode.

Rear wash
Under no cleaning and drying mode , and seating the toilet
Rotate forward by 45 ° to enter hip wash mode, which defaults to static wash mode, Rotate in this direction again to switch to mobile cleaning mode.

When starting up, short press the knob to send ceramic flushing command when there is no function.

Auto flush
When the seat sensor no longer detects a user , it will automatically flush . The toilet will only flush once.
Emergency Flushing
When the product is not powered-on , short press the rotated switch button on the side of the product or slightly touch the “Foot touch” button . It can achieve emergency flushing function If the above opearation does not work , you need to replace the battery or contact your local dealer.
Dryer flush Press the “Dryer”button
The warm air function is activated and a flush is performed. Rear / front wash is not available during flushing
Kick flush
Tap the “Kick button” with your foot for easy , manual flushing
Note that the “kick flush”function is available when user is sitting on the toilet seat .

Kick flush

Microwave induction
Microwave will detect any user within a 3ft radius.
Lid will open automatically for any user within a3ft radius. Close automatically when it no longer detects a user.
Kick to open lid / seat
Tap the “Kick Button” with your foot to raiseyour toilet lid / seat.
Tap the kick button once: Lid opens. Tap the kick button twice: Seat raises. Tap the kick button three times: Seat and Lid Will close and toilet will flush. Please do not touch the button forcefully Rear / front wash is not available during flushing

Smart Toilet User-friendly Design
Slow-closing lid /seat Preserve your toilet’s life and allows you to close the lid /seat silently .
Water purification Equipped with dedicated filter to ensure your bidet will only spray clean, filtered water. Damper The product has installed the damper which provide the toilet cover and toilet seat with a buffer function,to achieve the mute effect. 8 Layers of safety 8 different built-in safety features to protect the user and product.
Memory mode After power failure, water temp, water pressure, seat temp, and wand position are allrestored to mid-range after power failure.Night light is turned on by default after power failure.On / off, keep the last memorized setting state.
Self-cleaning Nozzle The washer can automatically clean, keeping bacteria and stains away.
Pre-flush After seating, the product will flush once towards the seat to ensure that the seat wall is moistened
Antibacterial Seat Antibacterial material is used for the seat

Smart Toilet Maintenance
Regular maintenance is required to ensure normal use
Note
Cut off the power and water supply before maintenance Direct water wash to the entire products is prohibited
Maintenance of product surface and ceramics
Wipe dust or stains with a soft wet cloth A wet soft brush , cloth or sponge may be used to clean the ceramic area
*Do not use abrasive cleaning solutions , such as alcohol,bleach , paint thinner , cresol, benzene ,gasoline ,etc.

WARNING
Do not spray water ordetergents on the toilet,remote control or the power cord. Doing so may cause electrick shock or fire.

Maintenance during Winter SeasonDuring winter season The water inside mayfreeze after long periods of storage andnon-usage.Please take measures to prevent.
Note
Before connecting the product to the watersupply and electrical outlet, allow it to defrostfor 30 mins in a warm indoor environment. In cases of extreme cold/freezing/nozzlestuck in place, wrap the water input line witha warm towel.Never pour hot water or use ahot dryer directly on the toilet.

Maintenance of the nozzle

Nozzle

Press the”Nozzle Clean”button on the remote control without occupying the seat. The nozzle will extend. Proceed to clean with a soft toothbrush.

Do not forcefully hold the nozzle,otherwise it may break. Please change the spout if itblocked.

Smart Toilet
Troubleshooting
If the user should run into any issues, please consult the troubleshooting guide below. lf problem persists,please contact a professional.

Power Button
Phenomenon
Not working

Fault Diagnoses
Check whether the attaching plug is loose or not
Check whether the power is switching on or off (the power light is not on)
Check whether there is any electric leakage or not

Solutions Please check the circuit
Press rotated switch for 3s, the power light is on.
Please unplug the attaching plug and contact with local distributor to repair.

Wash Function

Phenomenon

Fault Diagnoses

Solutions

Check whether or not the water supply cuts off

Wait for the water supply restoring

No water from the spout

Check whether or not the angle valve switches off
Check whether or not the water filter is blocked

Open the angle valve Clean the filter mesh or change the water filter

Check whether or not the inlet pipe is flexed

The inlet pipe must be straight

The intensity of cleaning is not strong enough

Check whether or not the water pressure or cleaning switch to low level or not
Check whether or not the inlet filter is blocked

Regulate the water pressure according to the instruction manual
Clean the filter mesh or change the water filter

Unusual water flow from the spout

Abnormal operation

Unplug the attaching plug for one minute and then plug it again

The water temp is not warm enough
The cleanser is always leaking

Check whether or not the water supply switches to low level
Solenoid valve no longer has any effect

Regulate the water temp according to the instruction manual
Please contact with our qualified maintenance personnel for repairing

The cleaning function The human induction system of the Please contact with our qualified maintenance is not working normally toilet seat no longer has any effect personnel for repairing

Dryer

Phenomenon

Fault Diagnoses

The dryer blows cold air

Check whether or not the dryer switches off
Check whether or not the heating element of dryer is damaged

Solutions
Regulate the temperature of dryer according to the instruction manual
Please contact with our qualified maintenance personnel for repairing

Heated Seat
Phenomenon

Fault Diagnoses

Solutions

The seat temp is too low Check whether or not the temp of

or is not hot

toilet seat is on the “off” position

Regulate the temperature of toilet seat according to the instruction manual

Remote Control
Phenomenon
The blue light of water temp is flickered
Remote control is not working

Fault Diagnoses

Solutions

Low battery

Please replace a new battery

Check whether or not there is any water on the remote control

Wipe off water by dry towel

Toilet
Phenomenon

Fault Diagnoses

Solutions

No power supply

Power restoration

The product is not flushed clean

No water from the spout
No water but have the sound of flushing
Have water all the time

Slow descent function

Phenomenon

Fault Diagnoses

The function of flipping the seat cover/ring up by foot touch cannot open or close

Auto-damping is damaged

Please contact with our qualified maintenance personnel for repairing
1.Check whether or not the pipeline is blended or not, please keep the water supply pipeline open and smooth 2.Check there is any damage of water pump Please contact with our qualified maintenance personnel for repair if there is any unusual from the water inlet valve
Solutions
1.Recharge after unplug the attaching plug. 2.Please contact with our qualified personnel if the following solution is not working.

Changes or modifications to this unit not expressly approved by the party responsible forcomplance could vold the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receive. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Smart Toilet Specifications

Rated voltage

Frequency

Rated power input

Seat and dryer temperature range

Dryer temperature range

Water supply hose type

Water Inlet

Minimum pressure Maximum pressure

Toilet

Flush type Rough-in

Heating type

Flushing

Washing temp range

Safety system

Dryer temp range

Dryer

Dryer air speed

Safety system

Heated seat

Heat temp range Safety system

Power cable length

120V60HZ 1050W(When inlet water temp in 59 4 diffdrent levels 35°C-55°C(95°F-130°F) DN15(G1/2″) 35psi,ensuring a flow of water at least 10.57GPF/min) About 40W Tornado flush Rough-in 12in Instant heating OFF/34°C-40°C (93-102)4 levels Butterfly thermostat, thermal fuse, flow sensor OFF/35°C-55°C (95-131)4 levels > 4m/s Thermal fuse, bi-metal OFF/34°C-40°C (93-102)4 levels Thermal fuse Appx.34.25 in

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>