EMX INDUSTRIES KPX-100 Programmable Keypad User Guide
- September 19, 2024
- EMX INDUSTRIES
Table of Contents
KPX-100 Programmable Keypad
“`html
Product Information
Specifications:
- Product Name: KPX-100TM Programmable Keypad TM
- Mode: Single-User-Mode and Multi-User-Mode
- Power Input: 12-24 Volts
Product Usage Instructions
Single-User-Mode Quick Start Guide:
- To enter programming mode, press 0 0 0 0 *
The center amber light will turn solid to denote programming
mode.
- Enter 8 9 0 0 #
The keypad will beep twice, setting the device to single user
mode. Note that this command factory resets existing codes.
- Enter 1 followed by your desired four-digit code, followed by
.
The KPX-100 will beep twice. Ensure this number does not match
the programming code.
- (Optional) Press 0 followed by your desired four-digit
programming code followed by #.
The keypad will beep twice. Remember to write down the new
programming code and store it securely.
- Press * to exit programming mode.
The amber light will resume blinking.
- Enter the four-digit opening code you assigned in step 3.
The keypad will activate on the 4th digit.
Multi-User-Mode Quick Start Guide:
- To enter programming mode, press 0 0 0 0 *
The amber light will turn solid to denote programming mode.
- Enter 8 9 0 1 #
The keypad will beep twice, setting the device to
Multi-User-Mode. The programming code in step 4 cannot match any
entry code in the system.
- Code 1: Enter 1 00 Your4digitcode #
Code 2: Enter 1 01 Your4digitcode #
Code 3: Enter 1 02 Your4digitcode #
- (Optional) Enter 0 followed by your desired 4-8 digit
programming code followed by #.
The keypad will beep twice. Remember to write down the new
programming code and store it securely.
- Press * to exit programming mode.
The amber light will resume blinking.
- Enter the opening code you assigned in step 3 followed by
.
The relay will activate.
FAQ
Q: What should I do if I forget my programming code?
A: If you forget your programming code, please contact our tech
support at 216-518-9889 or email
technical@emxinc.com for
assistance.
Q: Can I change my codes after setting them up?
A: Yes, you can change your codes by following the programming
instructions provided in the user manual.
“`
KPX-100TM
Programmable Keypad TM
Quick Start Guide
KPX-100 Quick Start Guide (Single-User-Mode)
This guide is to set up a simple single user code for activating the KPX-100.
Apply 1224 Volts to T1 and T2. Wire T4 and T5 to the Free Exit/ Exit loop
terminal as specified by your operator.
1. To enter programming mode Press 0 0 0 0
The center amber light will turn solid to denote programming mode.
2. Enter 8 9 0 0 #
The keypad will beep twice. This will set the device to single user mode.
NOTE: this command factory resets existing codes
3. Enter 1 ,followed by your desired four digit code,
followed by #. The Kpx-100 will beep twice. This number CANNOT match the
programming code.
4. (Optional) Press 0 followed by your desired four digit
PROGRAMMING CODE followed by #. The keypad will beep twice. Write new
programming code and store in a secure location.
5. Press to exit programming mode.
The amber light will resume blinking.
6. Enter the four digit opening code you assigned in step 3.
The keypad will activate on the 4th digit
See other side for Multi-User-Mode quick start
EMX Industries, Inc.
Tech support: 216-518-9889
1/2
technical@emxinc.com
KPX-100 Quick Start (Multi-User-Mode)
This guide is to set up 3 simple codes for multi-user-mode to activate the
KPX-100. Apply 12-24 Volts to T1 and T2. Wire T4 and T5 to the Free Exit/ Exit
loop terminal as specified by you operator.
1. To enter programming mode Press 0 0 0 0 *
The amber light will turn solid to denote programming mode.
2. Enter 8 9 0 1 #
The keypad will beep twice. This will set the device to Multi-User-Mode.
Note: Do step 4 first if using 58 digit codes instead of 4 digit codes. ENTRY
CODES AND PROGRAMMING CODE MUST BE THE SAME LENGTH.
The Kpx-100 can support up to 100 codes numbered 099 Entry codes can match
across users.
The programming code in step 4 cannot match any entry code in the system.
3. Code 1: Enter 1
00
Your4digitcode
Code 2: Enter 1
01
Your4digitcode
Code 3: Enter 1
02
Your4digitcode #
4. (Optional) Enter 0 followed by your desired 4-8 digit PROGRAMMING CODE followed by #.
The keypad will beep twice. Entry codes must be the same length as the programming code.
(Examples: Programming code 0 0 0 0 0 0 0 0
Entry code 1 2 3 4 5 6 7 8 , Programming code 0 0 0 0 0 0 Entry
code 1 2 3 4 5 6 )
Write new programming code and store in a secure location.
5. Press * to exit programming mode
The amber light will resume blinking.
6. Enter the opening code you assigned in step 3 followed by #.
The relay will activate.
See other side for Single-User-Mode quick start
EMX Industries, Inc.
Tech support: 216-518-9889
1/2
technical@emxinc.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>