ION Block Rocker Icon User Guide
- September 16, 2024
- ION
Table of Contents
Block Rocker Icon
“`html
Product Information
Specifications
- Brand: ION Audio
- Battery Type: Li-Ion
- Usage: Indoor and Outdoor
Product Usage Instructions
Charging and Battery Information
Here are some recommendations for getting the longest life from
the internal battery:
-
Fully charge the battery before using it.
-
Avoid full discharge of the battery if possible. Li-Ion
batteries are maintenance-free, and the battery will last longest
when operating between 30 and 80 percent charged. -
Do not use the product while charging the battery.
Storage:
For best product longevity, store product with a 50% battery
charge.
If you leave the battery level low and do not charge it for 6
months, it may permanently lose capacity.
Repair:
If the battery fails to charge, contact ION Audio at
ionaudio.com.
Disposal:
Bring the unit to a recycling center or dispose of in accordance
with local ordinances.
Outdoor Use and Care
Quick Start:
-
Make sure all items listed in the Box Contents are included in
the box. Look on top of the cardboard insert for the power
cable. -
Make sure all input devices (such as microphones, CD players,
or digital media players) are turned off with their volume settings
set to zero. -
Switch everything on in the following order:
-
Audio input devices (e.g. microphones, instruments, CD
players) -
Audio input devices
-
Balancing Your Levels:
This process shows how you can quickly balance your microphone
signal(s) and the signal from your Source Device (Bluetooth, Aux,
USB).
FAQ
Q: What should I do if my battery does not charge?
A: If the battery fails to charge, contact ION Audio at
ionaudio.com for repair assistance.
Q: Can I use the product while charging the battery?
A: No, it is recommended not to use the product while charging
the battery for safety reasons.
“`
BLOCK ROCKER® ICON
User Guide
English
Tap or click for technical
support.
ionaudio.com/support
TABLE OF CONTENTS
INTRODUCTION ……………………………………………………………… 4
Box Contents ……………………………………………………………………………………………….. 4 Support
…………………………………………………………………………………………………………. 4
SETUP ……………………………………………………………………………..5
Charging and Battery Information …………………………………………………………… 5 Outdoor Use and
Care ……………………………………………………………………………….. 6
FEATURES ……………………………………………………………………… 9
Front Panel …………………………………………………………………………………………………… 9 Rear Panel
……………………………………………………………………………………………………..11
OPERATION …………………………………………………………………… 13
Pairing a Bluetooth® Device ……………………………………………………………………… 13 Linking Two
Speakers ………………………………………………………………………………..14 Light
Modes………………………………………………………………………………………………….15 Using the
Radio……………………………………………………………………………………………15 USB
Mode……………………………………………………………………………………………………..18 Using the USB Charge
Port……………………………………………………………………….19 App
Control……………………………………………………………………………………………….. 20
TROUBLESHOOTING ……………………………………………………… 21
ION Audio Block Rocker® Icon User Guide
2
APPENDIX…………………………………………………………………….. 23
Technical Specifications …………………………………………………………………………… 23 Trademarks &
Licenses ……………………………………………………………………………..24
ION Audio Block Rocker® Icon User Guide
3
INTRODUCTION
Thank you for purchasing the Block Rocker® Icon Speaker. At ION, your
entertainment is as important to us as it is to you. That’s why we design our
products with one thing in mind–to make your life more fun and more
convenient. Note: Before you first use the product, please fully charge the
batteries. Your unit was purposely shipped with a reduced battery charge to
ensure safe transit. For optimal charging, power off the speaker while
charging. Use the included power cable to connect the unit to a power outlet
and let it charge for up to 3 hours. This helps ensure the longest life for
your battery.
Box Contents
Block Rocker® Icon IEC (C13) Power Cable (4.9 ft / 150 cm) Quickstart Guide
Support
For the latest information about this product (documentation, technical
specifications, system requirements, compatibility information, etc.) and
product registration, visit ionaudio.com. For additional product support,
visit ionaudio.com/support.
ION Audio Block Rocker® Icon User Guide
4
SETUP
Charging and Battery Information
For the quickest charging time, power off Block Rocker® Icon and use the
included IEC power cable connected to a power outlet. A full charge can take
up to 3 hours. The lightning bolt icon on the display will light up when Block
Rocker® Icon is connected to a power source and charging. The battery icon
will fill to display the battery life percentage. When charging is complete,
the lightning bolt icon will disappear, and the battery icon will be
completely filled.
ION Audio Block Rocker® Icon User Guide
5
Here are some recommendations for getting the longest life from the internal battery.
General Usage
Fully charge the battery before using it.
Avoid full discharge of the battery if possible. Li-Ion batteries are
maintenancefree, and the battery will last longest when operating between 30
and 80 percent charged.
Do not use the product while charging the battery.
Do not charge the battery in exceedingly hot (greater than 90°F/32°C) or exceedingly cold (less than 32°F/0°C) temperatures.
Storage
For best product longevity, do not store at exceedingly hot (greater than
90°F/32°C) or exceedingly cold (less than 32°F/0°C) temperatures.
For best product longevity, store product with a 50% battery charge.
If you leave the battery level low and do not charge it for 6 months, it may
permanently lose capacity.
Repair If the battery fails to charge, contact ION Audio at ionaudio.com.
Disposal Bring the unit to a recycling center or dispose of in accordance with local ordinances.
Outdoor Use and Care
Though Block Rocker® Icon is IPX5 water-resistant and able to tolerate
splashing water, please review the tips below to get the best performance from
your Block Rocker® Icon:
· Bring Block Rocker® Icon indoors during extreme weather.
· Please do not place Block Rocker® Icon in standing water.
· Please do not connect the power adapter to a Block Rocker® Icon in a wet
environment. Make sure the power input, power adapter, and power outlet are
all completely dry before making any connections.
· WARNING: Keep any non-water-resistant devices (phones, music players, etc.)
in a dry place where they will not be affected by water and cause a risk of
electric shock.
ION Audio Block Rocker® Icon User Guide
6
Quick Start
1. Make sure all items listed in the Box Contents are included in the box.
Look on top of the cardboard insert for the power cable.
2. Make sure all input devices (such as microphones, CD players, or digital
media players) are turned off with their volume settings set to “zero.”
3. Switch everything on in the following order:
a. Audio input devices (e.g. microphones, instruments, CD players)
b. Block Rocker® Icon
4. Adjust the level of your connected devices. Turn audio source
(instruments, Bluetooth devices) volume all the way up. If a microphone is
connected to the Mic In, press the Mic +/- Buttons on Block Rocker® Icon to
adjust the microphone volume to an appropriate level. Finally, adjust the
Volume +/- buttons on Block Rocker® Icon to an appropriate level. For a
detailed step-by-step process for setting your levels, please refer to the
Balancing Your Levels section on the following page.
5. When you are finished using Block Rocker® Icon, switch everything off in
the following order:
a. Block Rocker® Icon
b. Audio input devices
ION Audio Block Rocker® Icon User Guide
7
Balancing Your Levels
This process shows how you can quickly balance your microphone signal(s) and
the signal from your Source Device (Bluetooth, Aux, USB).
1. Press the Power button to turn on Block Rocker® Icon. Connect your
preferred Bluetooth, Aux device, or USB drive.
2. Using the Volume +/- buttons on the speaker, set the volume to around 5 or
lower while balancing your levels. This will allow you to set your levels to a
clear and audible level without being overpowering. You can adjust it again
later once a balance has been achieved.
3. Set the Mic In volume using the Mic +/- buttons on the speaker. Set the
level to 10 as a starting point if you’re unsure.
4. Now, set the volume on your Aux source device (Smartphone, tablet, etc.)
to 100%. This will guarantee a strong signal.
5. Start playback on your device and adjust the Volume +/- buttons on the
speaker until it reaches a clear and audible level. If you are using a
microphone, set the Mic +/- volume level to where you can still hear the
microphone above the music.
For specific troubleshooting steps, please see the Troubleshooting section.
ION Audio Block Rocker® Icon User Guide
8
FEATURES
Front Panel
Click a control below to jump to that section.
9 11
1
4 10
1. Display
6 72325 8
This screen shows information relevant to the current operation on Block Rocker® Icon.
Note: The Display comes with a plastic protector on it. Remove this for
optimal viewing.
· FM / USB / AUX / LINK icons: These icons will remain solid on when Block
Rocker® Icon is in those modes.
· Bluetooth icon: This icon will flash slowly when Block Rocker® Icon is in
pairing mode and will remain lit when a Bluetooth device is connected.
· Charge icon: This icon will remain lit when the power cable is connected,
and the battery is actively charging. When the battery is fully charged, the
charge symbol will turn off.
· Battery icon: This icon will remain on while being used and when actively
charging, even if Block Rocker® Icon is powered off. If Block Rocker® Icon is
off and the battery is fully charged, the battery symbol will turn off.
ION Audio Block Rocker® Icon User Guide
9
2. Previous / Next Buttons
In FM mode, press these buttons briefly to go to the previous or next station.
Press and hold these buttons to seek the previous or next strong station. In
Bluetooth and USB modes, press the Previous or Next button to go to the
beginning of the current track or skip to the following track, respectively.
Press the Previous button again within one second to skip to the previous
track. Press and hold both Previous / Next buttons for 5 seconds to reset the
speaker to factory defaults.
3. Play/Pause Button
Press this button to start and stop Bluetooth or USB audio. In FM mode, press
this button to save and recall radio presets. See Operation > Using the Radio
for more details.
4. Bluetooth® Button
Press this button to enter Bluetooth pairing mode. If there is no connection
made after 120 seconds, Bluetooth pairing will stop searching. When connected
to a Bluetooth device, press and hold this button to disconnect a paired
device and re-enter pairing mode. Once disconnected, press this button to re-
pair to the last connected device. See Operation > Pairing a Bluetooth® Device
to learn how to connect a Bluetooth device.
5. Stereo-LinkTM / Repeat Button
Double press this button to start stereo-linking to another Block Rocker®
Icon. See Operation > Linking Two Speakers for more details. In USB mode,
press this button to change the playback mode. See Operation > USB Mode for
more details.
6. Source Button
Press this button to cycle between FM, USB (when inserted), Bluetooth, and Aux
modes. The current mode will be shown on the Display. In radio mode, single
press the Bluetooth button to turn off the radio and switch to Bluetooth
playback.
7. Lights Button
Press this button to cycle through the light modes. See Operation > Light
Modes for more information. For the best lighting effect, you may need to
adjust the volume of your device and/or the Source volume.
ION Audio Block Rocker® Icon User Guide
10
8. EQ Button
Press this button to cycle through the Low, Mid, and Hi EQ frequencies. Then
press the VOL +/- buttons to adjust the EQ frequency settings from -12 to +12.
9. Mic +/- Buttons
Press these buttons to adjust the microphone volume.
TIP: For proper audio level mixing tips for Mic and other Source volumes, see the section Balancing Your Levels.
10. Volume +/- Buttons
Use these buttons to raise and lower the volume of the Bluetooth, USB, radio, or aux input from 0-16. Press and hold a button to raise or lower the volume quickly.
11. Power Button Press and hold this button to turn Block Rocker® Icon on and
off. Double press this button to enable or disable voice prompts.
Note: After 15 minutes of being in an idle state, the speaker will go into low
power mode. Press any button to wake it up. The speaker will maintain a
Bluetooth connection if the device is still within range. After 40 minutes
with no audio playing, the speaker will power down completely. In this state,
the power button will need to be used to turn the speaker back on.
ION Audio Block Rocker® Icon User Guide
11
Rear Panel
Note: Pull the tab on the protective rubber panel to release it and access the
rear panel port.
1 23
4
1. USB Charge/Playback Port
You can use this port for charging a USB device, such as a tablet or
smartphone. To charge a device that is streaming music via Bluetooth, pause
the music first and then wait for it to reconnect after the USB cable is
inserted.
Connect your USB flash drive here to play music. Use the Volume +/- buttons to
adjust the volume. Press the Stereo-LinkTM / Repeat button to cycle through
the five repeat/shuffle options. See the section USB Mode for more details.
Note: Your USB drive cannot be more than 128 GB and it must contain playable
MP3 files in order for its data to appear properly in the Display. When you
connect a USB drive with MP3 files, Block Rocker® Icon will order the files
alphabetically by folder on the root directory and then by track name in the
folder.
2. Aux In
Connect a CD player, MP3 player, or other audio source to this 1/8″ (3.5 mm)
input. Press the Source button to exit AUX mode or unplug the cable connected
to the Aux input.
3. Mic In
Connect a microphone (not included) into this into using a 1/4″ (6.35 mm)
cable. Turn the mic on if it has a power switch. Press the MIC +/- buttons to
control the mic volume.
4. Power Input Connect the included power cable here to charge the speaker.
ION Audio Block Rocker® Icon User Guide
12
OPERATION
Pairing a Bluetooth® Device
1 – PRESS
BLOCK ROCKER ICON
2
3
1. Turn on your Bluetooth device.
2. Turn on Block Rocker® Icon by holding down the Power button for 2 seconds.
When the unit is first turned on, it will automatically enter Bluetooth
pairing mode. If necessary, press the Bluetooth button to select Bluetooth
mode. The Bluetooth icon on the display will flash to indicate the speaker is
ready to pair and you will hear “Bluetooth Pairing” if voice prompts are
enabled.
3. Navigate to your device’s Bluetooth setup screen, find BLOCK ROCKER ICON,
and connect. The Bluetooth icon will appear in the display, and if voice
prompts are enabled, you will hear “Bluetooth Connected”. If after 90 seconds
if there is no connection, the speaker will stop searching for a Bluetooth
device and enter AUX mode.
Note: If you have previously connected to a Bluetooth device, Block Rocker®
Icon will reconnect automatically.
Note: If your Bluetooth device prompts for a pairing code, enter “0000”.
To disconnect a paired device, do any of the following:
· Turn off Bluetooth from your device’s Bluetooth settings. The speaker will
enter Bluetooth pairing mode to make it available for another device.
· Press and hold the Bluetooth button to disconnect and re-enter pairing mode.
The device will now be erased from memory and won’t automatically reconnect.
Once you have disconnected, you will hear “Bluetooth Disconnected” if voice prompts are enabled.
Tip: Double press the Power button to turn voice prompts on or off.
ION Audio Block Rocker® Icon User Guide
13
Linking Two Speakers
If you would like to play music from a Bluetooth device, you can first “link”
two Block Rocker® Icon speakers together in order to listen to your music in
stereo. One Block Rocker® Icon will serve as the left speaker and the other
will serve as the right speaker.
BLOCK ROCKER ICON
PRESS
PRESS
1 – DOUBLE PRESS
2 – DOUBLE PRESS
(on the Primary speaker)
(on the Secondary speaker)
3
To link two Block Rocker® Icon speakers together:
Note: When you begin the Stereo-LinkTM process, any connected Bluetooth
devices will be automatically disconnected. You can also disconnect your
device prior to beginning by pressing the Bluetooth button.
1. Double press the Stereo-LinkTM / Repeat button on both speakers to enter
Stereo-LinkTM mode. This first unit pressed will be the primary speaker (Left
channel).
Note: The linking process can take up to 30 seconds to complete. Speakers
should be within 50′ (15 m) of each other to properly link. The closer the two
speakers are, the quicker the link is established.
2. Once the speakers are linked, the primary speaker will automatically enter
Bluetooth pairing mode. Navigate to your device’s Bluetooth settings screen,
find BLOCK ROCKER ICON, and connect. When the connection is successful, you
will hear “Bluetooth Connected” from the primary speaker (if voice prompts are
enabled). When audio playback begins, you should hear it through both
speakers. The primary speaker will play the left channel while the secondary
speaker plays the right channel. Playback controls are active on both
speakers.
To disconnect two speakers or cancel linking between the two, double press the
StereoLinkTM / Repeat button on one Block Rocker® Icon. You will hear
“Bluetooth Disconnected” from the primary speaker to indicate the link has
been broken (if voice prompts are enabled.)
Note: Press and hold the Power button on each speaker while in Stereo-LinkTM
mode to power off the connected speakers. Block Rocker® Icon speakers powered
off in Stereo-LinkTM mode will automatically enter Stereo-LinkTM mode the next
time they are powered on and begin searching for secondary speakers to connect
to.
ION Audio Block Rocker® Icon User Guide
14
Light Modes
PRESS
When the speaker is first powered on, the side LEDs will send red lights from
the bottom to the top, lighting up all LEDs. The effect will hold for 2
seconds and then fade out. Then all LED’s will fade in and out until a
Bluetooth device is connected to the speaker. When paired, all lights will
flash blue 2 times.
Press the MIC +/- or VOL +/- buttons to have the lights increase from top to
bottom to show how loud the music or mic volume is. The Mic Volume color will
be yellow and the Music Volume color will be red.
Press the Light button repeatedly to toggle between one of the light modes
below. Press and hold Light Button for 3 seconds to switch to Utility Mode
(white light only). Single press the Light button again to return to the
previously selected light mode.
Note: For the best lighting effect, you may need to increase the volume of
your connected device or input source.
The LED light modes are:
· Falling Rainbow Beat Sync: A section of the color spectrum will flow
downward through the side lights. The speed is based on the intensity of the
bass frequencies. Low/No Bass = slow speed, Some Bass = average speed, High
Bass = fast speed.
· Starlight Effect Beat Sync: Randomly selected LEDs in all zones flash a
random color based on the bass frequency volume and slowly fade away. Low Bass
= Less Stars, High Bass = More Stars.
· Fire Pit: The side lights simulate the up and down movement of a fire.
· EQ Volume Beat Sync: The LEDs react to bass frequencies going up and down
with the music and the color fading throughout the color spectrum. Low/No bass
= slow speed, Some Bass = average speed, High Bass = fast speed.
· Bouncing Stars: The side LEDs will bounce up and down and fade up through
the color spectrum.
· Stacking Mode: Light drops fall down stacking up on each other until the
color reaches the top of the speaker. Once the light fills up the LEDs
completely, the next color in the spectrum will begin and repeat the process.
· Horizontal Waves: Three waves of one color flow down. After three waves have
gone from the top to the bottom, a new set of waves in the next color will
appear. Waves speed up or slow down based on bass frequency volume. High Bass
= fast speed, Medium Bass = average speed, Low Bass/No Bass = slow speed.
· Color Cycle: The side lights will show the same color while cycling through
the color spectrum.
ION Audio Block Rocker® Icon User Guide
15
· Static Color: The speaker will display one color that is selected from the
ION app. If a color is not selected, it will default to blue.
· Random: Cycles through the light modes, changing every 3 5 seconds. Static
Color and Utility Mode is not included in the random cycle.
· Utility Mode: All LEDs light up solid white.
· Off: All LEDs are off.
ION Audio Block Rocker® Icon User Guide
16
Using the Radio
PRESS
PRESS – Previous / Next Station HOLD – Seek
To use the radio, press the Source button so that FM is selected and shown on
the display.
While in FM mode, briefly press the Previous and Next buttons (</>) to move to
the previous or next station. Press and hold the </> buttons to seek for the
next strongest station in that direction.
1 – HOLD
2 – PRESS – Select Preset
3 – PRESS
To save a radio station as a preset:
1. Press and hold the Play/Pause button.
2. Use the </> buttons to select a preset number, 112, shown on the display.
3. When you have selected the desired preset number, quickly press and
release the Play/Pause button again to save it.
To recall a previously saved preset, press and release the Play/Pause button
to cycle through the saved presets.
ION Audio Block Rocker® Icon User Guide
17
USB Mode
1 – CONNECT AND PRESS
2 – PRESS
(Play/Pause Playback)
3 – PRESS
(Previous/Next Track)
4 – PRESS TO CYCLE
(ALL, FOLDER, ONE RANDOM)
When a USB drive with compatible files is inserted into the USB
Charge/Playback Port, Block Rocker® Icon will automatically switch to USB
mode. If the USB drive has already been inserted and you are using another
mode, press the Source button until USB mode is selected.
Block Rocker® Icon will automatically play the first compatible MP3 file.
Files are played in alphabetical order of what is on the root level, then
alphabetical by folder, and then alphabetical by track name. Media playback
will stop when all media has been played on the USB drive. Press the Next and
Previous (</>) buttons to go to the next or previous track. Press and hold
these buttons to fast forward or rewind within the track.
Note: The USB drive must have playable MP3 files for it to appear on the media
panel’s display.
With each press of the Stereo-LinkTM / Repeat button the following Repeat
settings will cycle through on the display:
· Play the current USB track on repeat (OnE). This is the default mode when
powered on.
· Play the tracks in random order (rAn).
· Play all the tracks on the USB drive on repeat (ALL).
· Play the current folder’s tracklist on repeat (FOLd). The folder used is
based on what song is playing when it is activated. For instance, if a song
playing is on the root level, selecting FOLd will repeat only songs at the
root level. If a song is in folder “A”, then only songs in folder “A” will be
repeated.
ION Audio Block Rocker® Icon User Guide
18
Using the USB Charge Port
To use the USB charge port: 1. Connect a USB type-A cable to the USB Charge
Port on the front panel of your Block
Rocker® Icon speaker (see image). 2. Connect the other end of the cable to the
charging input on your smartphone, tablet, or
other compatible device.
ION Audio Block Rocker® Icon User Guide
19
App Control
IMPORTANT: To ensure the best possible experience with the app, use the most
current Android OS or iOS on your device.
Follow these steps to download the free app on your device:
1. Open the Apple App Store or Google Play on your device. Then, search for
the ION Sound ControlTM app.
2. Follow the on-screen instructions to download and install the app. Once
downloaded, the ION Sound ControlTM app will appear on your device’s home
screen.
3. Connect your device to Block Rocker® Icon via Bluetooth. See Operation >
Pairing a Bluetooth® Device to learn how to do this.
4. Open the ION Sound ControlTM app. If prompted, allow the app to access
your device’s Bluetooth and Location Services.
5. Follow the steps on screen to find and connect to your Block Rocker® Icon.
Once connected, you can control various functions of the speaker, such as:
· Speaker and Mic Volume: Adjust the volume of the speaker and the Mic input.
· FM Radio Presets: Select from previously saved radio station presets and
also save radio presets.
· EQ: Adjust the speaker’s equalization.
· Lights: Change the light modes.
· Voice Prompts: Enable or disable the voice prompts.
· Battery Life: Check the speaker’s battery life status.
· Over-The-Air Firmware Updates: Stay up to date with the latest firmware
installation. · Support: Visit ionaudio.com, contact Technical Support, and
view Warranty
information and Frequently Asked Questions.
ION Audio Block Rocker® Icon User Guide
20
TROUBLESHOOTING
If the sound is distorted: You may need to adjust the levels of your sources
and Block Rocker® Icon for proper mixing.
i. First, turn your source volume all the way up. ii. Finally, adjust the
Volume +/- buttons to get an appropriate level.
If the sound is still distorted, try lowering the volume control of your sound
source, then use the Volume +/- buttons on Block Rocker® Icon to lower the
sound.
If the unit is not charging: Make sure the power cable is properly connected
to the power input and the power outlet.
If the sound is distorted: Try lowering the volume control of your sound
source.
I hear a hum when cables are connected: · Disconnect cables from the input
jacks to see if it’s a faulty cable. · Make sure the signal cables are not
placed near power cables. · Connect all audio equipment power cables to
outlets which share a common ground.
If there is a high-pitched whistling noise when using microphones: This is
probably feedback. Point the microphone away from the speaker.
If you can’t hear the microphone over the music volume: Turn down the music
volume from your source or increase the microphone volume using the Mic +
button.
If you cannot connect your audio device to Block Rocker® Icon via Bluetooth:
· Have your audio device (e.g., smartphone or tablet) and Block Rocker® Icon
as close together as possible while trying to connect. Make sure both the
audio device and Block Rocker® Icon are unobstructed by walls, furniture, etc.
· Press and hold the Bluetooth button to disconnect Block Rocker® Icon from
any other audio device and restart the search process. If this does not work
right away, power off Block Rocker® Icon and then power it back on. See
Operation > Pairing a Bluetooth® Device for more information.
· Reset the Bluetooth connection on your audio device by turning Bluetooth off
and back on. You can find this under the Bluetooth menu in the Settings for
your phone or other audio device.
ION Audio Block Rocker® Icon User Guide
21
If this does not work, and you have connected to Block Rocker® Icon before,
find Block Rocker® Icon in the list of available or previously connected
devices in your audio device’s Bluetooth menu, tap the “gear” or “i” icon
located next to it and then select Unpair or Forget. Turn Block Rocker® Icon
off and back on and try pairing again once it reappears in your available
devices list.
Note: If Block Rocker® Icon has been paired to another audio device recently
that is still within range, you may need to repeat this process with that
audio device to fully disconnect.
If you experience audio dropouts while playing music from a Bluetooth device,
this may be happening because your unit is trying to link to another speaker.
This can occur if you power off a speaker that was linked to your unit or if
you have just turned on your unit and it is in Stereo-LinkTM mode. To stop the
audio dropouts, exit Stereo-LinkTM mode by double-pressing the Stereo-LinkTM /
Repeat button. Alternatively, you can wait for your unit to link to another
speaker if there is one within range.
Press and hold both Previous / Next buttons for 5 seconds to reset the speaker
to factory defaults.
ION Audio Block Rocker® Icon User Guide
22
APPENDIX
Technical Specifications
Output Power Speakers
Water Resistance Frequency Response USB
Bluetooth
Battery
Power Dimensions
(width x depth x height)
Weight
180 W (peak) Low Frequency: 10.0″ (254 mm) woofer High Frequency: 3.0″ (76.2
mm) tweeter Full-Range Driver (sides): (2) 3.0″ (76.2 mm) IPX5 40 Hz 20 kHz
(-10dB) Supported File System: FAT32 Supported File Types: MP3 Maximum File
Size: 4 GB Maximum USB Storage Size: 128 GB Profile: A2DP, AVRCP Bluetooth
Version: 5.2 Range: Up to 100 ft. (30.5 m) * Stereo-LinkTM Range: Up to 75 ft.
(22.9 m) between speakers Capacity: 11.1 V/6000 mAh, 66.6 Wh Battery Life: Up
to 30 hours ** Charge Time: Up to 3 hours Cable: IEC (C13) Power Cable Input
Voltage: 100-240 V~, 50/60 Hz, 100 W 16.93″ x 11.02″ x 20.0″ / 430 x 280 x 508
22.51 lbs. / 10.21 kg
Specifications are subject to change without notice.
- Bluetooth and wireless reception and range are affected by walls, obstructions, and movement. For optimal performance, place the product so it is unobstructed by walls or furniture and is raised off the ground.
** Battery life may vary based on temperature, age, and volume usage of product.
ION Audio Block Rocker® Icon User Guide
23
Trademarks & Licenses
ION Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and
other countries. The Bluetooth word mark and logos are owned by the Bluetooth
SIG, Inc., and any use of such marks by ION Audio is under license. App Store
is a trademark of Apple Inc., registered in the U.S. and other countries.
Android and Google Play are registered trademarks of Google Inc. All other
product names, company names, trademarks, or trade names are those of their
respective owners.
ION Audio Block Rocker® Icon User Guide
24
ionaudio.com
Manual Version 1.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>