V-TAC VT-8603 LED Bulkhead Instruction Manual
- September 16, 2024
- V TAC
Table of Contents
V-TAC VT-8603 LED Bulkhead
FAQs
- Q: What should I do in case of any query or issue with the product?
- A: Please reach out to us at support@v-tac.eu for assistance.
- Q: How can I access the manual in multiple languages?
- A: Scan the provided QR code to access the manual in multiple languages.
- Q: What is the warranty period for each model?
- A: The warranty period is 5 years for VT-8603 and VT-8613, and 3 years for VT-8623 and VT-8633.
TECHNICAL DATA
MODEL| SKU| BEAM ANGLE| CRI| DF| LIFE SPAN
(HOURS)| INPUT VOLTAGE| MATERIAl| DIMENSION| WARRANTY
---|---|---|---|---|---|---|---|---|---
VT-8603| 801-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50/60Hz| PC| 320x100mm|
5 Year
VT-8613| 804-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50/60Hz| PC| 320x100mm|
5 Year
VT-8623| 806-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50/60Hz| PC| 320x100mm|
3 Year
VT-8633| 812-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50/60Hz| PC| 320x100mm|
3 Year
SPECIFICATIONS
SENSOR SPECIFICATIONS
MODEL| DETECTION ANGLE| DETECTION DISTANCE|
DETECTION RANGE MAX.| HOLD TIME| DAYLIGHT SENSOR|
DETECTION MOTION SPEED
---|---|---|---|---|---|---
VT-8613 VT-8633| 360° If Ceiling Mounting 120° If Wall mounting| 3-6 M|
D6Mx3M| 5s, 30s,90s, 3min,20min,30min| Day, 2LUX,10LUX- ,25LUX Optional|
0.5-3m/s
EMERGENCY SPECIFICATIONS
MODEL| EMERGENCY OPERATION TIME| EMERGENCY STANDBY WATTS|
BATTERY CHARGING CURRENT| BATTERY DISCHARGING CURRENT| BATTERY
TYPE| TEST BUTTON| CHARGING INDICATOR
---|---|---|---|---|---|---|---
VT-8623| >3 Hours| >1.2 Watts| 250mA| 410mA| LiFePO4, 3.2V, 2Ah| With| Green
LED
INTRODUCTION & WARRANTY
- Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference.
- If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product.
- They are trained and ready to serve you at your best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear.
- The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation.
- Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.
WARNING
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified person.
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.
- Caution, Risk of electric shock
- This marking indicates that this product should not be disposed of with other household wastes.
INSTALLATION INSTRUCTIONS
- Switch OFF the power before starting the installation.
- Remove the cover by holding the luminaire upside down. Press 3 clips on the sides pull the base upwards to open it and set aside.
- Carefully press and unlock the screw on the led hinged tray and hold the tray at an upward 90Degree position. Hold the product upside down.
- Hold the product in place, mark & drill the holes into the wall, and nail the alligator into the hole. Feed the supply cable into the luminaire through the cable entry hole.
- Once the base is installed, carefully put back the hinged tray by pushing it forward. Hold the tray with the base and twist the screw to lock it back.
- Carefully close the cover by aligning with the marked arrows on the base ( Locate the Side conduit) and the cover to avoid breakage while closing. Push down from all 3 sides to properly secure the 3 clips on the sides.
- Switch ON the power to test the light.
INSTRUCTIONS FOR CHANGING COLOR & POWER (AVAILABLE ON DRIVER)
| CCT | |
|---|---|
| ON | 3000K (Y) |
| ON | 4000K (WY) |
| ON | 6400K (W) |
| POWER | |
| --- | --- |
| ON | 20W |
| ON | 16W |
| ON | 8W |
PRE-INSTALL EMERGENCY FUNCTION TEST
- Connect the AC cable according to the diagram.
- Press the test button on the driver. The emergency function will be activated, and the charging indication will be off.
- Disconnect the battery pack, the charging indicated LED off.
- NOTE: After installation, allow 36 hours to ensure full battery charge and then interrupt the supply.
SENSOR SETTINGS
- Detection Area – It can be adjusted by combining DIP switches for specific applications [FIG 1].
- Hold Time – Period during which the light will be ON after the last detection [FIG 2].
- Daylight Threshold – Daylight sensor priors motion sensor. Set Threshold for Specific Needs. If disabled, only the motion sensor will work [FIG 3].
SENSOR APPLICATION
- When motion is detected, but the daylight is sufficient, the light will remain OFF.
- When motion is detected, and the daylight is insufficient, the light will be ON.
- After a stand-by period, the light will switch OFF.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>