HELM MK-M 140 G 169 Sliding Door System Installation Guide
- September 16, 2024
- HELM
Table of Contents
HELM MK-M 140 G 169 Sliding Door System Installation Guide
Technical information / Safety instructions
About these instructions
These instructions describe the installation of the sliding door system HELM
MK-M 140 glass – wall pocket installation with WTR
installation track, reversible. The installation is shown using the example of
a right-opening door. For left-opening doors, the installation must be carried
out in mirror image.
- certified according to DIN EN 1527:2013 (200.000 cycles)
- max. leaf weight: 140 kg
- suitable for tempered safety glass (TSG) and laminated safety glass (LSG consisting of two TSG panels)
- leaf thickness: TSG 8/10 mm, LSG 8,76/10,76 mm
- track length: up tp 3.100 mm
- the ratio of door height to door width must not exceed 2,5:1
- all dimensions in millimetre
Use glass leaves
- Glass panels with self-cleaning coating cannot be used with our fittings.
- Glass doors and glass elements that exhibit damages (e.g. edge damage, shell-shaped bursts, chips or scratches) must not be installed.
- Ensure the correct selection of the fittings.
- Set the gap dimension so that contact with hard materials is prevented on all sides.
- Check the necessity of an edge protection for edges above the floor or on longitudinal edges.
Intended use
- The sliding door fittings are only suitable for dry indoor spaces.
- Open and close hand-operated sliding elements using only the intended door handles and flush pulls.
- Do not slam and shove hand-operated sliding elements; slowly guide them into the desired position.
- Any other use is considered improper and will invalidate all liability and warranty.
Safety instructions
- Installation and commissioning may only be carried out by qualified personnel.
- Suitable protective clothing must be worn during installation.
- We recommend the installation to be carried out by two people.
- There is a risk of injury due to moving parts in the sliding area of the door leaf.
Requirements for the wall, ceiling and floor and the fixing material
- The load bearing capacity of the wall or ceiling must meet static and dynamic requirements.
- The substructure must be permanently capable of bearing loads, flat and plumb (max. tolerance 2 mm per metre).
- The fixing material must be suitable for the substructure and meet the static and dynamic requirements. Refer to the technical instructions for the fixing material.
- The fixing material is not included in the scope of delivery.
Maintenance
The hardware parts are almost maintenance-free and easy to clean. The
sliding door fittings must be checked regularly for signs of wear or damage.
Damaged systems may not be operated any longer. Furthermore, all fastening
elements such as screws, nuts, etc. must be checked and a functional test must
be carried out. Repair work must be carried out by qualified personnel or
specialist companies. Only original spare parts are to be used.
Cleaning
Do not clean anodized aluminum with acids or other alkaline cleaners.
Furthermore, scouring powder and steel wool should not be used for cleaning.
Dust, stains and light soiling can be removed with lukewarm water. Persistent
soiling such as gypsum or cement remnants can be easily removed if you add a
few squirts of a conventional wetting agent (like dish washing liquid) to the
water. A small squirt of a wetting agent is sufficient to obtain good results
during cleaning. We explicitly point out that the anodized coating can be
damaged by mortar and lime water. That means it is important that the bucket
with water does not contain any substances other than a wetting agent.
Disposal
Disassembly of the system is carried out in the reverse order of installation
and must be performed by qualified personnel. The product must be disposed of
in an environmentally friendly manner.
Refer to the national statutory regulations.
Drawing / Calculations
Calculations without door piston
Calculations with door piston
Scope of delivery
Required tools
Installation steps
The technical specifications are upto-date. We reserve the right to make modifications with regard to design and styling which serve the purpose of technical improvement. We appreciate your understanding that we assume no liability for any typing errors or any other errors. The reproduction of this document, in extracts or complete, is not permitted without our express written permission.
This installation instructions supersedes all previous installation instructions.
Woelm GmbH
Hasselbecker Str. 2 – 4
D-42579 Heiligenhaus
Tel. +49 (0) 2056 18-0
Fax +49 (0) 2056 18-21
www.woelm.de
contact@woelm.de
Woelm Austria GmbH
Seewalchen 5 A
A-5201 Seekirchen
Tel. +43 (0) 6212 2502
Fax +43 (0) 6212 6995
www.woelm.at
contact@woelm.at
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>