FENGMA 2333 Remote Control Car Instruction Manual
- September 13, 2024
- FENGMA
Table of Contents
FENGMA 2333 Remote Control Car
Thank you for using our company’s toy products. In order to have a better understanding of this product, please read the following instructions before use, which will bring you a different operating experience.
Note : This product is suitable for children 3 years old and above. After
assembled I charged by adults, play with children again. Please Use This
Product Under The Supervision Of An Adult.
Warning : please do not disassemble or modify the product without
authorization, any changes may cause the product to not work properly.
SPECIAL WARNING:
The output voltage used by the charging plug should be 5V. Please do not use the quick-charging plug and quick-charging cable, so as to avoid the condition that the too quick current output during charging causes overheated battery charging and results in dangerous matters such as product burnout.
Product Configuration
Gravity Watch Remote Control (2 options available)
Vehicle charging and battery installation
Battery Charging Mode
- Connect the Rechargeable battery pack to the USB charging cable
- Plug the other end of the USB charging cable into the USB port for charging
Attention : Before the battery of this car is almost depleted during use, it will sound two beeps and automatically shut down.
RIC Function introduction and battery installation
Indicator Light
Atomization lamp
| When the frequency is not correct, the light flashes, and when the frequency is up, the light goes out.
Tum on the atomization function and the light will be on; Tum off the atomization function and tum off the light.
---|---
Rotate 360 • to the right| Press the “Rotate 360 • Right” button while the
remote control car is in a stopped state, and the remote control car will
rotate 360 • to the right.
Deformation| When the remote control vehicle is in a stopped state, press the
“deformation” button, and the vehicle body will twist and arch up; Press the
button again to lower the vehicle body in parallel.
Programming| After pressing the programming keys, press the buttons that need
to be demonstrated one by one, and then press the programming keys. The remote
control car will start demonstrating in the order of input.
Left45°
ON/OFF/Lights
| When the RIC car is in the stop state, press down the”Left45• Travel”key, the RIC car travels left45•,
Long press to turn the power on or off; Briefly press to tum on or off the roof lights and light switch
Music| Press the first time to turn on music, press the second and third limes
to switch music, and press the fourth time to turn off sound.
Right45°| When the RIC car is in the stop state, press down the”Right45°
Travel”key, the RIC car travels Right45°.
Left Transverse| When the RIC car is in the stop state, press down the”Left
Horizontal Travel”key, the RIC car travels left horizontal.
|
Right Transverse| When the R/C car is in the stop state, press down the “right
horizontal travel key”, the R/C car travels right horizontal.
---|---
Forward/Backward| Push the forward and backward control lever of the remote
controller upward, the RIC car goes forward. Push the control lever downward,
the RIC car goes backward.
Tum Left/Tum Right| Push the joystick left and right of the remote control to
the left, and the remote control vehicle will turn left. Push the joystick to
the right to turn the remote control vehicle to the right.
Note : The effective control distance between the remote control and the vehicle is approximately 40 meters. If the remote control is out of frequency or does not operate during frequency synchronization, it will hibernate after 2minute. If operation is necessary, restart the remote control and the vehicle’s power switch.
Battery installation
Open the body battery cover and install 2x 1.5V “AA” non-rechargeable
batteries in the right polarity direction and cover the battery cover.
Function Description of Gravity Watch Remote Control
The gravity watch remote central effectively controls a distance of about 30 meters.
Gravity Watch Remote Control Battery Description
There are two options for the gravity watch remote control (operate according to the corresponding configuration in the figure below).
- Built in 3.7V lithium battery
- 3V CR2032 button battery
BUILT-IN BATTERY CHARGING
- Connect the gravity remote control to the USB charging cable.
- Insert the other end of the USB charging cable into the USB charging port.
INSTALL THE BATTERY
Open the battery cover of the gravity remote control and tighten the 3V CR2032 button Insert the battery compartment with the negative electrode facing downwards and cover it with the battery cover.
Handle Remote Control frequency alignment
- First, turn on the power switch of the vehicle body, and the lights of the entire vehicle will flash. Then, turn on the power switch of the remote control to start frequency matching. If the frequency matching is successful, the power light will flash red and blue.
- The frequency conversion is unsuccessful, and the remote control power light and body light keep flashing. If the connection is unsuccessful, please repeat the above operation.
- After frequency synchronization, there is no operation. After 2 minutes, the remote control car and remote control enter sleep mode, and the frequency synchronization connection needs to be reconnected
Frequency alignment of gravity watch remote control
- Long press the power switch of the gravity remote control to start frequency synchronization. If frequency synchronization is successful, the remote control lights 2 and 3 will light up. If there is no operation after 2 minutes, it will enter sleep mode.
- Frequency matching unsuccessful, remote control light 1 and light 4 keep flashing, connection unsuccessful. Please repeat the above operation
- After frequency synchronization, there is no operation. After 2 minutes, the remote control car and remote control enter sleep mode, and the frequency synchronization connection needs to be reconnected.
Operating Instructions for Gravity Watch Remote Control
MODEL 1
Palm down, forward light 2 lights up, remote control car moves forward;
Palm facing up, the reverse light 3 lights up, and the remote control car
moves backwards.
On the left side of the palm, light 4 is on, Remote control car turning left; On the right side of the palm, light 5 is on, Turn the remote control car to the right.
Raise the gesture, the R/C car body twists and arches; lower the gesture, the R/C car body twists and parallels.
MODEL 2 Palm down, forward light 2 lights up, Remote control vehicle moving forward; Palm facing upwards, The reverse light 3 lights up, and the remote control car moves backwards.
On the left side of the palm, light 4 is on, Remote control vehicle running horizontally to the left; On the right side of the palm, light 5 is on, Remote control car travels horizontally to the right.
Precautions For Using Water Tanks
- Please add an appropriate amount of clean water to the water tank before use. (As shown in the figure).
- When the water tank is dry, the atomization function cannot continue to operate. Long periods of water less operation can cause circuit board short circuits, leading to disordered or missing vehicle functions. Important notice: Due to the small size of the main body of this product and the small capacity of the water tank, only 6 grams of clean water can be added. Spray for 4 times or more. If you need to use the spray function again, add water again. Please insert the mouth of the water bottle into the mouth of the water tank and slowly squeeze it, filling it all at once.
Precautions For Battery Use
- Before playing please charge the new battery pack.
- The output voltage used by the charging plug should be 5V;
- The higher the actual milliampere of the rechargeable battery, the longer the charging time;
- Rechargeable batteries can only be charged under adult supervision;
- During charging, the light of the USB charging cable head is on red. When the light goes out, it indicates that the lithium battery is fully charged. The charging time is 3-4 hours.
- First plug the battery pack plug in the charger, then plug the charger plugged in the socket.
- Take out and put in the battery according to the mark on the toy battery room;
- Non-rechargeable batteries cannot be charged;
- Use only the same or identical battery as recommended;
- Do not mix-use old and new batteries or different types of batteries;
- Batteries should be placed in the correct polarity;
- Remove the exhausted battery from the toy;
- Power terminals should not be short-circuited;
- The charger must be checked regularly for damage to its wires, plugs, housings and other components. If damage is found, stop using the charger until it is repaired.
General Troubleshooting
Instructions
Battery chargers that use this toy must be regularly checked to prevent damage
to the wires and other components and, if damaged, must be repaired for
damage.
Maintenance Matters
- Can not close to the fire, avoid direct sunlight, high temperature and humidity or long-term in the car, to avoid short circuit, fire.
- Do not play when the car and remote control battery removed. And the remote control car, remote control I back into the color box packaging, to avoid damage or deformation during transport or storage.
- Remote control car with a damp cloth to gently wipe.
TIPS
When the car moves, please do not touch the wheels of the remote control car,
so as to avoid injury.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>