Fengma Toys Industry 2016477 Remote Control Car Instruction Manual
- June 9, 2024
- Fengma Toys Industry
Table of Contents
**Fengma**
REMOTE CONTROL DEFORMATION VEHICLE (2.4G)
INSTRUCTION MANUAL
2016477 Remote Control Car
Battery installation and charging mode for two kinds of battery tank in the car body
- Open the battery cover of the body, install the 3 x 1.2V “AA” rechargeable battery in the correct polarity direction, and close the battery cover.
- Use the USB charging plug to charge the battery. Due to the particularity of nickel-chromium battery charging, the light in the USB cable is the brightest in the case of no electricity. During the charging process, the light shall turn from bright to dark, but it will always light up. The charging time is 3 to 4 hours; If you do not want to use the rechargeable batteries that match with the product, you can also use other non-rechargeable 1.5V “AA” batteries.
- Open the battery cover of the body, install a set of 3.7V lithium batteries in the correct direction of the interface, and close the battery cover.
- Properly connect the 3.7V lithium battery to the charging cable, and use the USB charging plug to charge the battery. When charging, the red light will flash in the USB cable. When the light is not bright, it indicates that the lithium battery has been fully charged, with the charging time of 3 to 4 hours.
Remote control battery installation mode
Functions of remote Control
Precautions for battery use
The output power of charging plug is 5V;
The higher the actual milliampere of the rechargeable battery, the longer the
charging time;
Rechargeable batteries can only be charged under adult supervision;
Take out and put in the battery according to the mark on the toy battery room;
Non-rechargeable batteries cannot be charged; Use only the same or identical
battery as recommended;
Do not mix-use old and new batteries or different types of batteries;
Batteries should be placed in the correct polarity;
Remove the exhausted battery from the toy;
Power terminals should not be short-circuited;
The charger must be checked regularly for damage to its wires, plugs, housings
and other components. If damage is found, stop using the charger until it is
repaired.
2. 4G automatic code matching description
- Install the battery in car body, turn on the switch, and the Head Light will always flash.
- Install the battery of the remote control and start to connect. When the connection is successful, the Head Light stops flashing. Note: Failing to connect, please repeat the above operations.
- Each remote control can only be connected with one car. When the connection is successful, each car will not interfere with each other. Note: Do not connect multiple vehicles at the same time.
Instructions for operation
In the car state
Remote control goes forward and backward. When the joystick pushes up, the car
goes forward. When the joystick pushes down, the car backes up. Release to
stop. Remote control turns left and right. When the joystick pushes left, the
car turns left. When the joystick pushes right, the car turns right. Release
to stop.
In the autobot state
Remote control goes forward and backward. When the joystick pushes up, the
autobot goes forward. When the joystick pushes down, the autobot backes up.
Release to stop. Remote control turns left and right. When the joystick pushes
left, the autobot turns left. When the joystick pushes right, the autobot
turns right. Release to stop.
One-key transformation key: Press the “one-key transformation” key when the
car is stopped, and the car becomes an autobot immediately; Press the “one-key
transformation ” key again and the autobot transforms into a car.
Demonstration key: press the “Demonstration” key, the car goes into the
automatic demonstration mode; Press any key to exit the automatic
demonstration mode.
Product parameters
Remote control distance of the product: between 10 meters and 15 meters
Battery lite: about 30 minutes
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>