FOCAL FDP1900V2 Mono Channel Class D Car Audio Amplifier Instruction Manual

FDP1900V2 Mono Channel Class D Car Audio Amplifier

“`html

Specifications

• Model: FDP 1.900 V2
• Channels: 1
• Power Ratings: 14.4v DC

Product Usage Instructions

Power Per Channel

All power ratings are at 14.4v DC.

Input/Output Configurations

When using both left and right inputs, they are mixed to mono,
which is useful for subwoofers.

Crossover Configuration

Not specified in the provided manual excerpt.

Automatic Power Turn On/Off

1. Connect the REM wire from your source radio to the REM
   amplifier terminal for automatic power control.

2. If your source radio has a BTL amplifier, connecting the
   high-level BTL speaker wires to the RCA input can trigger auto turn
   on without the REM wire.

RCA Input, Both Low Level and High Level

Not specified in the provided manual excerpt.

Setting Level

Not specified in the provided manual excerpt.

Setting Subwoofer High Pass Subsonic Filter

Not specified in the provided manual excerpt.

2 Ohm Subwoofer Power Recommendation

Not specified in the provided manual excerpt.

Amplifier Configurations

Detailed configurations and settings for using the amplifier
with various setups like a 3-way kit, subwoofer, bridged mode, and
parallel cascade mode are provided. Refer to the graphics A1, A2,
A3, and A4 for specific configurations.

Power Fuses & Balanced/Unbalanced Switch

Instructions on how to use power fuses and switch settings are
given in the manual excerpt.

Troubleshooting

Detailed troubleshooting steps for issues like the focal sign
not lighting, flashing, no sound, or blown fuses are provided.
Follow the steps mentioned to diagnose and resolve the
problems.

FAQ

Frequently Asked Questions

Q: My amplifier blows a fuse when I turn it on. What
should I do?

A: Troubleshoot by checking the power and ground connections,
fuse integrity, and ensure correct polarity. If the issue persists,
further inspection or professional service may be required.

“`

FDP 1.900 V2: ONE CHANNEL AMPLIFIER OPERATION / CONFIGURATION MANUAL
POWER PER CHANNEL
· 1 x 500w RMS into 4 ohms @ 1% THD · 1 x 850w RMS into 2 ohms @ 1% THD · 1 x 500w RMS into 1 ohm @ 1% THD · 1 x 1700w RMS (Two FDP 1.900 V2s Bridged into 4 ohms) @ 1% THD
All power ratings are at 14.4v DC.
INPUT/OUTPUT CONFIGURATIONS
Because this is a one channel amplifier, if both left and right inputs are used, they are mixed to mono, which is useful for subwoofers.
CROSSOVER CONFIGURATION
· The 24 dB per octave crossover can be adjusted for subwoofers or midbass in 3-way kits. · The Band Pass crossover has high pass between 10Hz – 48 Hz, and low pass between 40Hz – 350Hz. · The remote volume control is always active.
There is a clip distortion light on the remote volume control. If you see this light on, reduce volume until the light goes out so that you do not damage your speaker. · Phase is continuously adjustable between 0 degrees and 180 degrees. Adjust by measuring frequency response at the crossover frequency. Frequency response should be as smooth as possible. · 40 Hz EQ is adjustable between 0dB and +6dB. Measure the subwoofer frequency response and adjust EQ to get the smoothest frequency response. Avoid excess EQ boost because this will make the subwoofer sound “muddy” and cause the amplifier have clip distortion prematurely.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio connected to the REM amplifier terminal.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not necessary.
RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL
· The amplifier LEVEL control has sufficient adjustment range for both low level and high level input into the RCA jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers, can be directly connected to the RCA jacks when the amplifier LEVEL control is adjusted to 8V.
1

SETTING LEVEL
· The best way to set system levels is to use a D’Amore Engineering DD-1 and test signals. Follow their gain overlap instructions.
· Set the amplifier LEVEL control to minimum before you turn on the amplifier for the first time. · For lowest distortion and lowest noise the amplifier LEVEL should be set at the lowest setting that yields
sufficient loudness without distortion. For lowest noise your source radio volume control should be near maximum that does NOT cause distortion. · To find the best amplifier LEVEL setting if you are NOT using a DD-1: 1) With the amplifier LEVEL at minimum, slowly increase the source radio volume until you hear distortion. Then turn it down to until the distortion stops. 2) Next, slowly turn up the amplifier LEVEL control to the maximum desired loudness, or until the red LED light flashes on the music’s ocassional peaks. (The LED turns on when there is distortion that can damage your speakers.) Listen very carefully and turn down the amplifier LEVEL control if you hear any distortion.
SETTING SUBWOOFER HIGH PASS SUBSONIC FILTER
· A subwoofer should have a high pass filter often called a subsonic filter. The purpose of a subsonic filter is to limit very low frequencies that your subwoofer can not play loud enough without damage. Removing subsonic frequencies can allow your subwoofer to play louder.
· For a sealed box the high pass is typically set between 10 Hz and 30 Hz to increase power handling capacity. · For a vented box the high pass filter must be set 5 Hz lower than the port tune frequency to prevent woofer
damage.
2 OHM SUBWOOFER POWER RECOMMENDATION
· If you use two 2ohm subwoofers, your total power is 500 Watts (only 250 Watts per woofer). If you use two FDP 1.900 V2 amplifiers – one on each 2ohm woofer, your total power will be 1700 Watts (850 + 850), or 5 decibles louder.
2

ONE AMPLIFIER USING A 3-WAY KIT (SEE GRAPHIC A1 )
A1 (ONE AMP USING A 3-WAY KIT)

RADIO 350Hz

48Hz

MASTER

WOOFER OF 3-WAY KIT +­

ONE AMPLIFIER USING A SUBWOOFER (SEE GRAPHICS A2 )
A2 (ONE AMP USING A SUBWOOFER)

RADIO 80Hz

20Hz

REMOTE SUB CONTROL MASTER

SUBWOOFER +­

3

TWO AMPLIFIERS IN BRIDGED MODE (SEE GRAPHIC A3)
· DO NOT use a 2 Ohm Speaker.
· TWO FDP 1.900 V2 amplifiers are required.
· Amplifier #1 will have “MASTER” switch selected. Amplifier #2 will have “DIRECT” switch selected.
· Crossover and level controls will only function on MASTER amplifier #1.
· By selecting “DIRECT” on amplifier #2 all crossover and level controls are bypassed and the LEFT input channel must be used.
· Master Amplifier #1 will receive the source signal on left and right channels. Master Amplifier #1 RCA “out -” will connect to direct amplifier #2 RCA “L IN”. The LEFT input channel must be used.
· The (speaker +) will connect to Amplifier #1 (+ speaker). The (speaker -) will connect to Amplifier #2 (+ speaker).
· The (speaker -) on Amplifier #1 will connect to (speaker -) on Amplifier #2.

A3 (2 AMPS BRIDGED)

RADIO 80Hz

20Hz

REMOTE SUB CONTROL MASTER

DIRECT

SUBWOOFER

­

4

MULTIPLE AMPLIFIERS IN PARALLEL CASCADE MODE (SEE GRAPHIC A4)
· TWO or more FDP 1.900 V2 amplifiers are required. 1. Use this mode when you have several speakers that will use the same crossover and loudness setting and will have one amplifier on each speaker. 2. One example is a dual voice coil subwoofer and you use one amplifier on each voice coil. 3. A second example is you have several subwoofers and will use one amplifier on each subwoofer.
· Amplifier #1 will have “MASTER” switch selected. Amplifier #2,3,4…. will have “DIRECT” switch selected.
· Crossover and level controls will only function on amplifier #1. · By selecting “DIRECT” on amplifier #2,3,4…. all crossover and level controls are bypassed and the LEFT input
channel must be used. · Master Amplifier #1 will receive the source signal on left and right channel.
Master Amplifier #1 RCA “out +” will connect to direct amplifier #2,3,4…. RCA “L IN”. The LEFT input channel must be used. · One speaker + & – will connect to one Amplifier’s + & -.
A4 (2 AMPS PARALLEL)

RADIO 80Hz

20Hz

REMOTE SUB CONTROL MASTER

DIRECT

+ ­

DUAL VOICE COIL

SUBWOOFER

­

5

POWER FUSES & BALANCED/UNBALANCED SWITCH
FDP 1.900 V2 POWER FUSES

TO USE: Remove the end panel by the power terminals 2 x 25 amp ATC fuse
FDP 1.900 V2 BALANCED/UNBALANCED SWITCH

TO USE:

Remove the end panel by the RCA jacks. The standard switch position is input ground “ON”. Flip the switch “OFF” changes the input to “balanced input floating ground”. To flip the switch, use a small pick or jewelers screw driver.

6

TROUBLESHOOTING

FOCAL SIGN DOES NOT LIGHT
1. Measure the voltage at the amplifier power terminal. It should be between 12 and 15 volts.
2. Measure the voltage at the amplifier REM terminal. It should be between 12 and 15 volts.
3. If you are using BTL high level for automatic turn on, try connecting a REM wire. 4. Check your power and ground connections to be correct polarity + and – and they are tight. 5. Check battery connections. 6. Check the fuse in the REM wire. 7. Check fuse at battery. 8. Check fuse inside amplifier.
The fuse is inside the right end cap beside the power terminals. The recommended ATC fuse size is two 25 amp.
FOCAL SIGN IS FLASHING
1. Is the amp very hot? Wait a few minutes for it to cool down. You need to get more fresh cool air to the amplifier. Do not cover the amplifier or mount it flush into a hole.
2. If the amp is cold and the Focal sign is flashing, there is an internal fault. The amplifier must then be returned for service.
NO SOUND
1. Is the Focal sign light off or flashing? 2. Is the source radio on and is there a sound signal coming from the source radio? 3. Use an ohm meter and measure the speaker wires for short circuit. 4. Check connections for small “wire whisker” that may be shorting between amplifier terminals or speaker
terminals. 5. Use an ohm meter and measure the speaker for short circuit. 6. Double check your connections to the source radio. 7. Are you using the correct source radio wires and are they plugged into the correct amplifier RCA? 8. Double check your connections to the speakers and speaker crossovers. 9. Check that all amplifier switches are in the correct positions for your speaker set up. 10. Check that HP & LP frequencies are set correctly for your speakers. 11. If little or no sound, make sure that you are do not have crossover points overlapping or HP/LP frequency
reversed.
AMPLIFIER BLOWS FUSE WHEN YOU TURN IT ON
1. Power and ground may be reversed. Check + and – polarity at amplifier and at battery.
SUBWOOFER REMOTE VOLUME CONTROL DOES NOT FUNCTION
1. Check that Remote Volume Control wire is plugged into the amplifier securely. 2. The Remote Volume Control will not function if the amp switch is “DIRECT”. The switch must be in “MASTER”.
7

SUBWOOFER REMOTE VOLUME CONTROL LED LIGHT
1. While playing music the LED light should be Green. Occasional red LED light flash indicates that the amplifier has reached maximum loudness.
2. If the red LED light flashes with the beat of the music, TURN DOWN THE VOLUME before you damage your speaker.
3. If the red LED light is on continuous, TURN DOWN THE VOLUME before you damage your speaker.

WARRANTY INFORMATION
Focal America / Orca Design & Manufacturing supports their products and guarantees them to be free of manufacturing defects for a period of 1 year (non-transferrable) from the date of purchase, if purchased from and authorized retailer. This time period is extended to 3 years (non- transferrable) from the date of purchase, if the amplifier is purchased from and installed by an authorized retailer, and no alterations are made to the installation or setup of the amplifier outside of the authorized retailer.
This manufacturing warranty does not extend to situations involving physical or installation damage, misuse, abuse, or modification. If an amplifier malfunctions, please return it to the authorized retailer from which the amplifier was purchased to have the amplifier and/or installation inspected and to have the warranty period verified from date of purchase.
The authorized dealer will then work with Focal America / Orca Design & Manufacturing to obtain service, if necessary. If found to be a defect due to manufacturing, the item will be repaired or replaced with a refurbished amplifier. The amplifier will be returned to the authorized retailer when repairs are complete, so that the dealer can return the amplifier to you, or reinstall the amplifier to maintain the above mentioned warranty timeline.

TECHNICAL SPECIFICATIONS

1 X 500w RMS into 4 ohms @ 1% THD 1 X 850w RMS into 2 ohms @ 1% THD 1 x 500w RMS into 1 ohm @ 1% THD 1 x 1700w RMS (Two FDP1.900V2sBridged into 4 ohms) @ 1% THD Frequency Response 10 Hz to 350 Hz. S/N ratio 90 dB RCA input can use a BTL source or common ground source. RCA switch select balanced floating ground or grounded to minimize noise. Input sensitivity 200mV to 10 volts Slew Rate 13 V / uS

Input has a peak limiter to prevent severe distortion and speaker damage. It allows light clipping. Variable band pass crossover 10 Hz to 350 Hz, 24 dB Linkwitz-Riley Variable bass boost, 0 to +6dB at 40 Hz. Continuous phase adjustment from 0 to 180 degree. Subwoofer remote volume control includes a clipping indicator light. Recommended DC voltage operating range 11.5 to 14.4 volts. Minimum DC voltage operating range 8 to 16 volts. Length 7.71 inches Width 10 inches Height 1.97 inches Weight 6 pounds

8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>