AQUA MEDIC N Kauderni CF Aquarium Reef Builders Instruction Manual

AQUA MEDIC N Kauderni CF Aquarium Reef Builders

Product Information:

The N Kauderni CF is a saltwater aquarium system manufactured by AB Aqua Medic GmbH. The system includes all the essential components required for a complete setup, such as the aquarium, cabinet, protein skimmer, LED light, and circulation pump. The
total capacity of the system is approximately 195 liters. The dimensions of the aquarium are 65.5 x 60 x 60 cm, with a water level of 50 cm.

Included Components:

• 1 Aquarium (65.5 x 60 x 60 cm) with frame
• 1 Cabinet
• 1 Aquarius 60 plus LED light
• 1 Separated cover with fan
• 1 Protein skimmer EVO 500
• 1 Circulation pump DC Runner 2.3 (refer to separate manual)

Note: The package does not include a heater stick, timer, or socket board.

Overflow System and Filter Chamber:

The overflow system is inserted into the overflow shaft of the Kauderni CF using the supplied PVC tube key. The filter chamber consists of a circulation pump, filter sponge, skimmer, emergency overflow, and filter inlet. The system is designed to ensure proper
water circulation and filtration.

Product Usage Instructions

Setting up the Aquarium

1. Choose a suitable location for the aquarium.
2. Place the aquarium on a stable surface, ensuring it is level.
3. Install the cabinet according to the provided instructions.

Installing the Overflow System and Filter Chamber:

1. Insert the overflow system into the overflow shaft using the supplied PVC tube key.
2. Tighten the nuts of the bushings using the supplied PVC tubes with moulded keys on one side.
3. Refer to Fig. 2 for the correct installation of the bushings.
4. Make sure to tighten all connections before use.

Connecting Additional Components:

If required, connect the following additional components:

• Heater Stick: Select a heater stick suitable for your aquarium environment. Install it according to the manufacturer’s instructions.
• Timer: If desired, connect a timer to control the lighting or other electrical components.
• Socket Board: Connect a socket board if you need additional power outlets.

Maintaining the Lighting System:

Take care to prevent humidity and salt from entering the interior of the lighting system. Ensure sufficient thermal exchange by operating the light with running fans. Failure to provide proper aeration may result in overheating and damage to electrical
components. Be cautious of condensation, which can cause overheating or corrosion.

For further information and spare parts, please visit www.aqua- medic.de.

The saltwater aquarium Kauderni CF is a complete system that comes with all vital elements. It is delivered including the protein skimmer EVO 500, the LED light aquarius 60 plus, the circulation pump DC Runner 2.3 and a cabinet incl. filter tank. The whole content is approx. 195 litres.
Dimensions: 65.5 x 60 x 146 cm (aquarium 65.5 x 60 x 60 cm), water level 50 cm.
1. Included in shipment
The aquarium system Kauderni CF consists of the following components:

Kauderni CF

• 1 aquarium 65.5 x 60 x 60 cm, incl. frame
• 1 cabinet
• 1 x aquarius 60 plus
• 1 x separated cover incl. fan
• 1 protein skimmer EVO 500
• 1 circulation pump DC Runner 2.3 (see separate manual)

Not included are a heater stick, a timer and a socket board.
The power of the required heater stick depends on the temperature of the aquarium environment. If it is installed in an unheated room, it should have a power output of approx. 250 watts. In heated rooms, 100 – 150 watts are sufficient.

Overflow system and cabinet filter

The overflow system is inserted in the overflow shaft of the Kauderni CF with the supplied PVC tube key.

Fig. 1: Overflow system

1. Emergency overflow to the filter
2. Outflow to the filter
3. Nut for bushing
4. Slide ring for bushing
5. Glass bar (no pict.)
6. Rubber sealing ring
7. Outlet emergency overflow
8. Adjustion valve
9. Return line
10. Tube for cable entry
11. Overflow to the filter
    Available spare parts: Please refer to www.aqua-medic.de.

Fig. 2: Filter chamber Kauderni CF

1. Circulation pump DC Runner 2.3
2. Filter sponge
3. Skimmer EVO 500
4. Emergency overflow
5. Filter inlet

In the cabinet, there is a ball valve (Fig. 1, No. 8) that has to be slightly closed to control the water in the overflow box. If the valve is closed to heavily or the return flow is blocked for some reason, the water rises in the aquarium and flows to the filter tank through the emergency overflow. In such a case, the ball valve has to be opened a bit further and all blockages have to be eliminated. If the overflow makes loud noises, the ball valve has to be closed a bit more so the water is bottled up stronger so that no air is dragged along. At least in the initial phase this has to be controlled regularly and, if necessary, to be adjusted. With the supplied PVC tubes with moulded keys on one side for holding the nuts of the bushings (tank fittings), these nuts can be tightened or released. The bushings have to be installed according to Fig. 3. Always re-tighten before use. The slide ring and nut have to be mounted manually beforehand and tightened as much as possible. The rubber slide ring must always be attached to the side of the rotable nut, the rubber gasket on the opposite side of the panel.

Fig. 3 : Bushing or tank fitting (the glass pane is placed between slide ring 3 and rubber ring 2)

1. Thread
2. Rubber sealing
3. Slide ring
4. Nut

There is a blue fitting in the mounted bend of the return line. Here, air is sucked in when the pump in the cabinet fails. This prevents the formation of communicating pipes and an overflow of the filter tank by returning water.
When starting the aquarium, water has to be filled in until the filter tank is filled up to 10 – 12 cm in the front part and then the pump has to be started. If the water level in the filter tank decreases, water has to be filled in until the a.-m. maximum is reached. Take care that enough space is left so that the inflowing water in case of failure or shutdown of the circulation pump still fits into the filter tank. The cables of circulation pumps or other parts mounted in the aquarium can be routed through the empty conduit downwards. If a plug is too big for this, the profile slid onto the rear panel can be cut with a PUK saw so that cables can be led out of the aquarium at the back. The back side should, however, remain closed to allow the fan to suck in air in the aquarium and not from the outside.

Skimmer EVO 500

See separate manual. The skimmer is hooked to the rear wall of the filter sump with the holding unit without screws (refer to Fig. 2).

Lighting aquarius 60 (please refer to the attached manual)

Fig. 4: Holder for aquarius plus

• Take care that no humidity and no salt enters the interior of the lighting system!
• Pay attention to a sufficient thermal exchange! The light must not be operated without running fans. Missing aeration may result in overheating and damage electrical components. Overheating or corrosion due to condensation may occur.

Cover with fan

The fans are connected to the supplied transformer. The fans are adjustable and should remain constantly in operation at low power. Otherwise, water will condense in the LED lights during the dark phase. If the outside temperatures are high, the fans can be operated with higher speed.

Maintenance
The fans should be cleaned regularly, in particular the salt residues have to be removed. The fans can be exchanged separately. Only exchange the faulty fan for an original Aqua Medic fan. Only these are suitable for the installation to aquaria.

Set-Up

Before setting up the aquarium, please make sure that the load-bearing capacity of the base is sufficient for the filled system as a whole.
The floor must be firm and level. It must not give under pressure.
The contact surface between the glass base and the surface of the base cabinet must be free of any kind of dirt. The use of a mat between the glass base and base cabinet is expressly not recommended.

Warranty conditions

AB Aqua Medic GmbH grants the first-time user a 24-month guarantee from the date of purchase on all material and manufacturing defects of the device. Incidentally, the consumer has legal rights; these are not limited by this warranty. This warranty does not cover user serviceable parts, due to normal wear & tear i.e: impellers or drive wheels etc. The original invoice or receipt is required as proof of purchase. During the warranty period, we will repair the product for free by installing new or renewed parts. This warranty only covers material and processing faults that occur when used as intended. It does not apply to damage caused by transport, improper handling, incorrect installation, negligence, interference or repairs made by unauthorized persons. In case of a fault with the unit during or after the warranty period, please contact your dealer. All further steps are clarified between the dealer and AB Aqua Medic. All complaints and returns that are not sent to us via specialist dealers cannot be processed. AB Aqua Medic is not liable for consequential damages resulting from the use of any of our products.

AB Aqua Medic GmbH – Gewerbepark 24 – 49143 Bissendorf/Germany

– Technical changes reserved – 01/2022/v13

References

• Aqua Medic GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>