SelectBlinds Modern Textured Roller Shades Motorized Installation Guide
- September 11, 2024
- SelectBlinds
Table of Contents
SelectBlinds Modern Textured Roller Shades Motorized
Product Specifications
- Product : Motorized Roller Shades with Cassette
- Control : Motorized with Cassette
- Installation : Top-Fixing or Face-Fixing
- Child Safety Feature: Chain Tensioner
Product Usage Instructions
Fitting the Brackets
The brackets offer two methods of installation:
- Top-Fixing: Use the front two holes in the top of the bracket to fix to the lintel (the ‘ceiling’ of the recess).
- Face-Fixing: Use two screws through the back plate to mount it onto a facing surface (a wall or window frame).
Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.
Fitting the Shade
- Top-Fixing: Bracket (side-on)
- Face-Fixing: Shade (side-on)
Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket. Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.
Chain Tensioner Installation
Shades with clutch controls come with a continuous chain loop that should always be secured to the wall using the included chain tensioner. Follow these steps for installation:
- Mark the desired location of the screw holes for the tensioner and drill pilot holes.
- Install the tensioner with screws ensuring it is fully installed for smooth chain movement.
- The tensioner should keep the chain taut but not stretched to ensure safety.
No-Drill Blinds Headrail Installation
- Remove the existing product from the headrail.
- Prepare the No-Drill Blinds Headrail by retracting the tension boot and installing metal strips or adhesive tape if needed.
- Insert the No-Drill Blinds Headrail into the window opening and secure it by extending the tension spring.
- Install the product onto the brackets and test for secure installation and smooth operation.
Fitting the brackets
The brackets offer two methods of installation:
-
Top-Fixing
Use the front two holes in the top of the bracket to fix to the lintel (the ‘ceiling’ of the recess). -
Face-Fixing
Use two screws through the back plate to mount onto a facing surface (a wall or window frame)
Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across thewidth.
Fitting the shade
Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket. Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.
Child Safety
Chain Tensioner
- Shades with clutch controls come with a continuous chain loop, which should always be screwed to the wall with the included chain tensioner.
- The chain tensioner should be installed to a flat surface, so the bead chain is taut but not stretched. Be sure not to twist or cross the chain.
- On inside mount shades, the tensioner may be attached to the windowsill or to the inside of the window frame. For outside mount or wall mount shades, the bracket may be mounted to the exterior of the window frame or the wall.
- With a pencil, mark the desired location of the screw holes for the tensioner and then drill pilot holes. Then install the tensioner with the screws, making sure that the tensioner is fully installed, so that the spring is pushed in and the chain passes smoothly through the guide.
The chain tensioner forms an important safety function by keeping chain loops away from small children. Never operate this shade without a functioning and correctly installed chain tensioner. Please retain these instructions for the future reference. Thank you for purchasing this product. Please read the instructions and warning carefully before installation to ensure safe and satisfactory use of this product.
The difficulty level of this installation is ranked at Level 1. A piece of
cake!
If you have questions or get stuck, call our Customer Care Team at
888-257-1840, or email
customercare@selectblinds.com
Remove the No-Drill Blinds Headrail
The No-Drill Blinds Headrail will already be installed onto the existing product headrail. Remove the product from the headrail (See Fig A), which will vary from product and depend on lift type.
Preparing the No Dril Blinds Headrail
Pull the lever from below or push down on the mechanism from above to retract
the tension boot (See Fig B). Install the metal strips or padded adhesive tape
on opposite sides of the window opening where you’ll be installing the No-
Drill Blinds Headrail. This is optional and only available on larger products.
Installing the No Drill Blinds Headrail!
Insert the No-Drill Blinds Headrail into the window opening, make it flush
with the top of the window opening, then push on the lever to extend the
tension spring and secure the No-Drill Blinds Headrail.
Installing the Product
Install the product onto the brackets (See Fig D). Test and operate the
product to ensure secure installation and smooth functionality.
Uninstalling the No Drill Blinds Headrail
To uninstall the product, follow step 1 by removing the product from the
headrail and use a screwdriver to unlatch the lever. Make sure to hold the No
Drill Blinds Headrail in place while unlatching the lever. This will prevent
damage to the window or headrail.
Tech Tip
If the fixed boot end was accidentally forced out, use a flathead screwdriver
to twist the red “droplets” towards the center and then push it back in.
FAQ
Q: How do I ensure proper installation of the chain tensioner?
A: Mark and drill pilot holes for the tensioner, install it securely, and
ensure the chain is taut but not stretched for safety.
Q: Can I install the No-Drill Blinds Headrail without using metal strips or
adhesive tape?
A: It is optional but recommended for larger products to provide
additional support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>