PROLiGHTS EclDisplay CRMX FC 40W RGB Plus WW LED Spotlight User Manual
- September 13, 2024
- PROLIGHTS
Table of Contents
- EclDisplay CRMX FC 40W RGB Plus WW LED Spotlight
- Specifications
- Product Usage Instructions
- Safety Information
- Packaging
- Installation
- Connection
- Start-Up
- Maintenance
- Q: Can this product be used for residential purposes?
- Q: How far should the product be placed from the lens of the
- Q: How should I dispose of the product at the end of its
EclDisplay CRMX FC 40W RGB Plus WW LED Spotlight
“`html
Specifications
- Product: EclDisplay CRMX FC
- Power: 40W
- Light Type: RGB+WW LED Spotlight
- Control: Wireless CRMX and wired control
- Additional Features: Without lens
Product Usage Instructions
Safety Information
Before using the product, please read the safety information
provided in the manual. This unit is designed for professional
applications and should be kept at least 0.5 meters away from the
lens of the projector.
Packaging
Package Content: Ensure all components
mentioned in the packaging section are included.
Installation
Mounting: Follow the instructions provided in
section 5 for proper installation of the product.
Connection
Connection to the Mains Supply: Use the
terminal block for connecting to the mains supply and DMX line as
described in sections 6 and 7.
Start-Up
Connect and Disconnect Power: Follow the steps
in section 7 to safely power on and off the product.
Maintenance
Maintenance and Cleaning: Regularly clean and
maintain the product as instructed in section 12 to ensure optimal
performance.
FAQ
Q: Can this product be used for residential purposes?
A: No, this product is designed for professional applications
only and should not be used in households.
Q: How far should the product be placed from the lens of the
projector?
A: Maintain a minimum distance of 0.5 meters (1.64 ft) from the
lens of the projector for safe operation.
Q: How should I dispose of the product at the end of its
life?
A: Please dispose or recycle the product according to local
regulations regarding Electrical and Electronic Equipment (WEEE) to
preserve the environment.
“`
EclDisplay CRMX FC
40W RGB+WW LED Spotlight with Wireless CRMX and wired control, without lens
USER MANUAL
Rev.01 – 07/24
English version
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet
quality and performance requirements for professionals and designed and
manufactured for the use and application as shown in this document. Any other
use, if not expressly indicated, could compromise the good condition/operation
of the product and/or be a source of danger. This product is meant for
professional use. Therefore, commercial use of this equipment is subject to
the respectively applicable national accident prevention rules and
regulations. Features, specifications and appearance are subject to change
without notice. Music & Lights S.r.l. and all affiliated companies disclaim
liability for any injury, damage, direct or indirect loss, consequential or
economic loss or any other loss occasioned by the use of, inability to use or
reliance on the information contained in this document. Product user manual
can be downloaded from the website www.prolights.it , or can be inquired to
the official PROLIGHTS distributors of your territory
(https://www.prolights.it/sales_network.html). Scanning the below QR Code, you
will access the download area of the product page, where you can find a broad
set of always updated technical documentation: specifications, user manual,
technical drawings, photometrics, personalities, fixture firmware updates.
Visit the download area of the product page
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document
pertaining to PROLIGHTS services or PROLIGHTS product are trademarks OWNED or
licensed by Music & Lights S.r.l., its affiliates, and subsidiaries. PROLIGHTS
is a registered trademark by Music & Lights S.r.l. All right reserved. Music &
Lights Via A. Olivetti, snc 04026 – Minturno (LT) ITALY
INDEX
SAFETY INFORMATION
02
1 – PACKAGING
05
PACKAGE CONTENT ……………………………………………………………………………………….. 05
2 – OPTIONAL ACCESSORIES
05
DEDICATED ACCESSORIES………………………………………………………………………………. 05
NORDIC ALUMINUM TRACK ……………………………………………………………………………. 05
3 – TECHNICAL DRAWING
06
4 – TILT RANGE
09
5 – INSTALLATION
10
MOUNTING…………………………………………………………………………………………………….. 10
6 – CONNECTION TO THE MAINS SUPPLY
11
CONNECTION TO MAINS VIA TERMINAL BLOCK………………………………………………. 12
CONNECTION TO DMX LINE VIA TERMINAL BLOCK …………………………………………. 12
7 – START UP
13
CONNECT AND DISCONNECT POWER FROM THE PRODUCT……………………………. 13
8 – PRODUCT OVERVIEW
13
9 – RDM FUNCTIONS
14
10 – DMX CHARTS
19
11 – ACCESSORIES INSTALLATION
25
OPTICS (CODES ECLDISPWASHL1530 / ECLDISPWASHL2550 / ECLDISPPRZL2040 –
OPTIONAL)……………………………………………………………………………………………………… 25
BARNDOOR AND FILTER FRAME (CODE ECLDISPBDNFFB – OPTIONAL) ……………… 27
ANTI-GLARE LOUVRE (CODE ECLDISPLOUVRE – OPTIONAL)………………………………. 28
GOBO HOLDER (CODE ECLDISPGOBOHIND – OPTIONAL)…………………………………. 29
HALF SNOOT, FULL SNOOT (CODES ECLDISPHSNOOT, ECLDISPFSNOOT –
OPTIONAL)……………………………………………………………………………………………………… 30
CEILING ADAPTER KIT (CODES ECLDISPCEILKIT, ECLDISPCEILFLG – OPTIONAL) …. 31
12 – MAINTENANCE
34
MAINTENANCE AND CLEANING THE PRODUCT……………………………………………….. 34
VISUAL CHECK OF PRODUCT HOUSING …………………………………………………………… 34
TROUBLESHOOTING……………………………………………………………………………………….. 35
PROLIGHTS – EclDisplayCRMX FC
01
0,5 m
Ta 45°C
SAFETY INFORMATION
WARNING! · See https://www.prolights.it/product/ECLDISPLAYCRMXFC#download for
installation
instructions. · Please read carefully the instruction reported in this section
before installing, power-
ing, operating or servicing the product and observe the indications also for
its future handling.
This unit is not for household and residential use, only professional
applications.
Connection to mains supply · The Connection to the mains supply must be
carried out by a qualified electrical installer. · Use only AC supplies
100-240V 50-60 Hz, the fixture must be electrically connected
to ground (earth). · Select the cable cross section in according with the
maximum current draw of the
product and the possible number of products connected at the same power line.
· The AC mains power distribution circuit must be equipped with
magnetic+residual
current circuit breaker protection. · Do not connect it to a dimmer system;
doing so may damage the product.
Protection and Warning against electrical shock · Do not remove any cover from
the product, always disconnect the product from AC
power before servicing. · Ensure that the fixture is electrically connected to
ground (earth). And use only a
source of AC power that complies with local building and electrical codes and
has both overload and ground-fault (earth-fault) protection. · Before using
the fixture, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected
devices. · Isolate the fixture from power immediately if the power plug or any
seal, cover, cable, or other components are damaged, defective, deformed or
showing signs of overheating. · Do not reapply power until repairs have been
completed. · Refer any service operation not described in this manual to
PROLIGHTS Service team or an authorized PROLIGHTS service center.
Installation · Make sure that all visible parts of the product are in good
visible condition before its
use or installation. · Make sure the point of anchorage is stable before
positioning the projector. · When suspending the fixture above ground level,
secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety
attachment for the weight of the fixture to the attachment point on the main
frame of the product. ln case the safety cable, enter in action, it needs to
be replaced with a new one. · Install the product only in well ventilated
places. · For non temporary installations, ensure that the fixture is securely
fastened to a loadbearing surface with suitable corrosionresistant hardware. ·
For a temporary installation with clamps, ensure that the quarter-turn
fastener and/or screws are turned fully, and secured with a suitable safety
cable.
Minimum distance of illuminated objects · The projector needs to be positioned
so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
Max operating ambient temperature (Ta) · Do not operate the fixture if the
ambient temperature (Ta) exceeds 45 °C (113 °F).
02
PROLIGHTS – EclDisplayCRMX FC
Ta -10°C Tc 65°C
Minimum operating ambient temperature (Ta) · Do not operate the fixture if the
ambient temperature (Ta) is below -10 °C (14 °F).
Protection from burns and fire · The exterior of the fixture becomes hot
during use. Avoid contact by persons and materials. · Ensure that there is
free and unobstructed airflow around the fixture. · Keep flammable materials
well away from the fixture · Do not expose the front glass to sunlight or any
other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the fixture, creating a potential
fire hazard. · Do not attempt to bypass thermostatic switches or fuses.
Indoor use · This product is designed for indoor and dry environments. · Do
not use in wet location and do not expose the fixture to rain or moisture. ·
Never use the fixture in places subject to vibrations or bumps. · Make certain
that no inflammable liquids, water or metal objects enter the fixture. ·
Excessive dust, smoke fluid, and particle build up degrades performance,
causes
overheating and will damage the fixture. · Damages caused by inadequate
cleaning or maintenance are not covered by the
product warranty.
Temperature of the external surface · The surface of the fixture can reach up
to 65 °C (149 °F) during operation. Avoid
contact with people and materials.
Maintenance · Warning! Disconnect the fixture from AC mains power and allow to
cool for at least
10 minutes before handling. · Only technicians who are authorized by PROLIGHTS
or Authorised service partners
are permitted to open the fixture. · Users may carry out external cleaning,
following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred
to a qualified service technician. · Important! Excessive dust, smoke fluid,
and particle build up degrades performance, causes overheating and will damage
the fixture. Damages caused by inadequate cleaning or maintenance is not
covered by the product warranty.
Photobiological safety · This device emits potentially dangerous optical
radiation and is identified in the cat-
egory of Risk Group 2 according to EN 62471.
Do not stare at the operating light source · Do not look directly at the LED
source during operation. It can be harmful to the eyes
and skin. · During Installation, operation and maintenance, be prepared for
the fixture to light
and move suddenly when connected to power. · The device should be positioned
so that prolonged staring into the luminaire at adis-
tance closer than 2,0 m (6,56 ft) is not expected.
Minimun distance
Risk Group 2
Risk Group 1
0.2 m 0.7 ft
2,0 m 6,56 ft
PROLIGHTS – EclDisplayCRMX FC
03
Disposal · This product is supplied in compliance with European Directive
2012/19/EU Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please
dispose/ recycle this product at the end of its life according to the local
regulation.
The products to which this manual refers comply with: · 2014/35/EU – Safety of
electrical equipment supplied at low voltage (LVD). · 2014/30/EU –
Electromagnetic Compatibility (EMC). · 2011/65/EU – Restriction of the use of
certain hazardous substances (RoHS).
FCC Compliance: · This device complies with Part 15 of the FCC Rules.
Operation is subject to the fol-
lowing two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may
cause undesired operation.
Other approvals · The product meets the safety requirements of the
certification procedures of the
market in which it is placed and sold.
04
PROLIGHTS – EclDisplayCRMX FC
1 – PACKAGING
PACKAGE CONTENT · 1x ECLDISPLAYCRMXFC; · User Manual.
2 – OPTIONAL ACCESSORIES
DEDICATED ACCESSORIES
Check the updated accessories list, description and informations of the
product at the following link:
https://www.prolights.it/product/ECLDISPLAYCRMXFC#accessories
NORDIC ALUMINUM TRACK NOTE: the final terms “2” and “3” in the codes indicate
the corresponding color variant in black and white respectively. ·
NAXTSC61002/3: global Pulse XTSC Lighting Track, 3 circuit DALI, 1000mm,
black/white; · NAXTSC62002/3: global Pulse XTSC Lighting Track, 3 circuit
DALI, 2000mm, black/white; · NAXTSC63002/3: global Pulse XTSC Lighting Track,
3 circuit DALI, 3000mm, black/white; · NAXTSC64002/3: global Pulse XTSC
Lighting Track, 3 circuit DALI, 4000mm, black/white; · NAXTSC6112/3: global
Pulse XTS Connector 3-CCT DALI end feed, earth right, black/white; ·
NAXTSC6122/3: global Pulse XTS Connector 3-CCT DALI end feed, earth left,
black/white; · NAXTSC6142/3: global Pulse XTS Connector 3-CCT DALI middle
feed, black/white; · NAXTSC6232/3: global Pulse XTS Connector 3-CCT DALI
flexible corner connector, black/white; · NAXTSNC6342/3: global Pulse XTSN
Connector 3-CCT DALI L connector, earth right, black/white; · NAXTSNC6352/3:
global Pulse XTSN Connector 3-CCT DALI L connector, earth left, black/white; ·
NAXTSNC6362/3: global Pulse XTSN Connector 3-CCT DALI T connector, earth
right/right, black/white; · NAXTSNC6372/3: global Pulse XTSN Connector 3-CCT
DALI T connector, earth left/left, black/white; · NAXTSNC6382/3: global Pulse
XTSN Connector 3-CCT DALI X connector, black/white; · NAXTSNC6392/3: global
Pulse XTSN Connector 3-CCT DALI T connector, earth right/left, black/white; ·
NAXTSNC6402/3: Global Pulse XTSN Connector 3-CCT DALI T connector, earth
left/right, black/white; · NAXTS412/3: global Pulse XTS Connector 3-CCT DALI
END cap, black/white; · NASPW12SK215M: global Pulse Track clip wire suspension
set 1.5m, 150N, black; · NASPW12SK25M: global Pulse Track clip wire suspension
set 5m, 150N, black; · NASPW12SK315M: global Pulse Track clip wire suspension
set 1.5m, 150N, white; · NASPW12SK35M: global Pulse Track clip wire suspension
set 5m, 150N, white; · NASKB122/3: global Pulse Track Mounting Clamp for Rod
and Wire, 200N, black/white; · NAXTSC6212/3: global Pulse XTS Connector 3-CCT
DALI straight connector, black/white.
PROLIGHTS – EclDisplayCRMX FC
05
3 – TECHNICAL DRAWING
1[1[040.45.511i1[min0m4[2]n.[2m]570m1.700.i90m9in[2]minm70m]n.m]09m imn]m
Ø60 mm Ø[[ØØØ[6Ø2206..2440m.4iimnnmi]]nm] 146 mm 1[14546.86mimnm]m [5[5.8.8inin] ] Weight: 1.79 kg – 3.94 lbs Ø60 mm Ø[[ØØØ[6Ø2206..2440m.4iimnnmi]]nm]
78 mm
228 mm 2[298.0minm]
77[388.1mmimnm] [3.1 iinn]] [9.0 in]
Ø82 mm ØØ8[328.22mmimnm] [3[.32.2ini]n]
ECLDISPLAYCRMXFC with ECLDISPWASHL1530
[2[2171070.00.6[26im1i7mn0]mn0.]m6 imn]m [2[1261060.0[0.2313i6mi0mn0.]nm]m3 imn]m
1[1[04.045.151[1i0mi4nm.2[]5n2[]m107m07.i0.m09n92[]imi0m7mn.n]0]9mm imn]m
146 mm 1[[1455[456..886.8miimnnimn]]m] Weight: 1.81 kg – 3.99 lbs Ø74 mm Ø[[ØØØ[7Ø2247..2994m.9iimnnmi]]nm]
69 mm
219 mm 22[[[188189..9.666mmiiinnnmm]]]
6[6[[22299…777mmiiinmnnm]]]
Ø82 mm Ø[Ø38[[.33282..222minmiim]nnm]]
ECLDISPLAYCRMXFC with ECLDISPWASHL2550
1[66.1[03661[.[2i06m6392n..]0[2i9m3m092n[2i.]im9m92mn0n.]]9im0mmni]mmn]m
[319[531.1[934511.i9m54n1.]mim4nim]mn]m
11[1887[8557.35.3mmimnimmn]m] [7.3 in]
333[[1144433999..77mmmiinmnmm]]
111[[979979.99.88mmmiinnmmm]] [7.8 in] [13.7 in]
Weight: TBD kg – TBD lbs
06
ØØ5959mmmm
[Ø2.3 in]
Ø[ØØ39[.37998.778minmmim]nmm] ECLDISPLAYCRMXFC with ECLDISPPH[3D.8ZiLn2]040
Fig. 01
PROLIGHTS – EclDisplayCRMX FC
Ø59Øm59mmm [Ø2[.Ø3 2Øin.35] 9inm] m
[Ø2.3 in]
Ø9Ø7[39m.78m[m3in.m8] in] [3.8 in] [312323.273 imnm]mm 3[2132.7minm] [12.7 in]
229 mm 1[166.6030[2 i[92[2m.nm9992].0.mi9m00mni]immnn]]m 16[06.3m imn] [6.3 in]
229 mm
1[875.13[87m1i5.[n387m]m5.i3nmm]inm] Weight: 2.15 kg – 4.74 lbs Ø71Ø[Øm72Ø[1Øm.87m21i.nm8m]inm] [Ø2.8 in]
2[2[2[111888111111…111mmmiiinmnmnm]]] 111[[353[5351.1.212.m2minimmni]mn]m] Ø8Ø28m2mmm [3.2[3i.nØ2] i8n2] mm [3.2 in] ECLDISPLAYCRMXFC with ECLDISPPRHDL18-36-50
[6.3 in] [61.630in]mm
i2n2]9 mm [m92[.m290.9i0ni]mn]m
42[411261.m6 immn]m 421 [m1m6.6 in] [16.6 in] [9.0 160 mm [6.3 i1n6]0
185 mm 185[7m.3min] [7.3 in] 185 mm [7.3 in]
230 mm
380 mm [31840.9minm] [14.9 in] 380 mm
[293.00 imn]m [9.0 in] 230 mm [9.0 in] [14.9 in]
Weight: 2.26 kg – 4.98 lbs Ø74 mm [Ø2.9 in] Ø74 mm [Ø2.9 in]
Ø95 mm [3Ø.79i5n]mm
[3.7 in] ECLDISPLAYCRMXFC with ECLØD9IS5PmPRmL08
[3.7 in]
i2n]29 mm [9.0 in] [6.3 in]
385 m[31m855.2 imn]m [15.2 in] [6.3 i1n]60 mm
[9.0 mm
229 mm
Ø74 mm [Ø2.9 in]
in] 160
[9.0 160 mm [6.3 in]
185 mm [7.3 in] 185 mm [7.3 in] 185 mm [7.3 in] Weight: 2.19 kg – 4.82 lbs
193 mm
[7.6 in]
343 mm [13.5 in]
193 mm [7.6 in]
343 mm
[13.5 in]
385 mm [15.2 in]
193 mm [7.6 in] 343 mm [13.5 in]
Ø99 mm [3.9 in]
ECLDISPLAYCRMXFC with ECLDØI9S9PPmRmZL1020 [3.9 in]Fig. 02
Ø60 mm [Ø2.4 in]
PROLIGHTS – EclDisplayCRMX FC
Ø99 mm 07
229 mm
229 mm [9.0 in] 160 mm [6.3 in] 346 mm [13.6 in]
Ø60 mm [Ø2.4 in] 185 mm [7.3 in] Weight: 1.99 kg – 4.38 lbs
[3.9 in] 154 mm [6.1 in] 304 mm [12.0 in] Ø82 mm [3.2 in] ECLDISPLAYCRMXFC with ECLDISPPRZL2040
08
PROLIGHTS – EclDisplayCRMX FC
4 – TILT RANGE 90°
TILT RANGE: 135°
225° PROLIGHTS – EclDisplayCRMX FC
Fig. 03
09
5 – INSTALLATION
MOUNTING Check that the supporting structure can safely bear the weight of all
installed fixtures, clamps, cables, auxiliary equipment, etc. and complies
with locally applicable regulations. When suspending the fixture above ground
level, secure it against failure of primary attachments by attaching a safety
wire that is approved as a safety attachment for the weight of the fixture to
an anchor point on the product main frame. Do not use removable parts or weak
anchors for secondary attachment. Warning! When clamping the fixture to a
truss or other structure at any angle, use clamps of half-coupler type. Do not
use any type of clamp that does not completely encircle the structure when
fastened.
C6002 clamp
RSR0630A/B Steel security cable
Track system
17 [0.7]
97 [3.8]
37 [1.4]
Ø4 [Ø0.2] Ø13 [Ø0.5] Dimensions are in mm / in – Fig. 04
10
PROLIGHTS – EclDisplayCRMX FC
6 – CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the fixture must be earthed! The
product is equipped with auto-switching power supply that automatically
adjusts to any 50-60Hz AC power source from 100-240 Volts. If you need to
install a power plug on the power cable to allow connection to power outlets,
install a grounding-type (earthed) plug, following the plug manufacturer’s
instructions. If you have any doubts about proper installation, consult a
qualified electrician. The max power consumption is 35W. 1
1
2 2
2
Remove the plastic cover to acces to the screw terminal blocks.
PROLIGHTS – EclDisplayCRMX FC
Fig. 06
11
+
+
- _
CONNECTION TO MAINS VIA TERMINAL BLOCK CONNECTION TO DMX LINE VIA TERMINAL BLOCK
N L
Fig. 07
DMX
GND
Fig. 08
12
PROLIGHTS – EclDisplayCRMX FC
7 – START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT To apply and disconnect power to
the product: · Check that the product is installed and secured as indicated in
the Safety Informations, and that
personal safety will not be put at risk when the fixture lights up. · Connect
the external led driver to the mains line. · The product is then ready for its
operations and can be controlled through the available input sig-
nals on led driver. · To disconnect power from the product, disconnect the
mains from the socket.
8 – PRODUCT OVERVIEW
1. SAFETY EYE to attach safety cable; 2. KNOB for releasing and locking the
optic; 3. KNOB for adjusting zoom and focus; 4. OPTIC (accessory not included,
in the figure ECLDISPWASHL1530); 5. RUBBER RING (accessory included in the box
optic); 6. KNOB for adjusting dimmer or CCT (only VW version); 7. REMOVABLE
PLASTIC COVER to access to the screw terminal blocks; 8. PLASTIC ARM COVER; 9.
LOCK TILT.
6 7
8
9
1 2 3 4 5
PROLIGHTS – EclDisplayCRMX FC
Fig. 09
13
9 – RDM FUNCTIONS
The product can communicate using RDM (Remote Device Management) protocol over
a DMX512 Networks. RDM is a bi-directional communications protocol for use in
DMX512 control systems, it is the open standard for DMX512 device
configuration and status monitoring. The RDM protocol allows data packets to
be inserted into a DMX512 data stream without affecting existing non-RDM
equipment. It allows a console or dedicated RDM controller to send commands to
and receive messages from specific fixtures.
Product ECLDISPLAYCRMXFC
Model ID D156
Mode IDs
BASIC: 5 STANDARD: 6 EXTENDED: 15 BASIC 16 BIT: 10
The PIDs in the following tables are supported in the product.
Category
Parameter
Value GET
SET
SUPPORTED_PARAMETERS PARAMETER_DESCRIPTION
0x0050
x
0x0051
x
Product Information
DMX512 Setup
PRODUCT_DETAIL_ID_LIST DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL
DEVICE_LABEL FACTORY_DEFAULTS DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION
DMX_START_ADDRESS
SLOT_INFO
0x0070
x
0x0080
x
0x0081
x
0x0082
x
x
0x0090
x
x
0x00E0
x
x
0x00E1
x
0x00F0
x
x
0x0120
x
SLOT_DESCRIPTION DEFAULT_SLOT_VALUE
0x0121
x
0x0122
x
Sensors
SENSOR_DEFINITION SENSOR_VALUE
0x0200
x
0x0201
x
x
DIMMER_INFO
0x0340
x
CURVE
0x0343
x
x
CURVE_DESCRIPTION
0x0344
x
x
Dimmer Settings OUTPUT_RESPONSE_TIME
0x0345
x
x
OUTPUT_RESPONSETIME DESCRIPTION
0x0346
x
MODULATION_FREQUENCY
0x0347
x
x
MODULATIONFREQUENCY DESCRIPTION
0x0348
x
DEVICE_HOURS
0x0400
x
x
LAMP_HOURS
0x0401
x
x
Power/Lamp LAMP_STRIKES
0x0402
x
x
Settings
LAMP_STATE
0x0403
x
x
LAMP_MODE
0x0404
x
x
DEVICE_POWER_CYCLES
0x0405
x
x
Control
IDENTIFY_MODE
0x1040
x
x
14
PROLIGHTS – EclDisplayCRMX FC
Manufacturer Specific PIDs
Parameter
PID GET SET Value
Description
DMX FAULT
MASTER/SLAVE
STANDALONE MODE
STATIC COLORS
CCT WHITE PRESETS COLOR MACRO
MANUAL RED MANUAL GREEN MANUAL BLUE MANUAL WARM WHITE
FULL ON STUDIO RED STUDIO GREEN STUDIO BLUE STUDIO WARM WHITE WHITE
CALIBRATION RED WHITE CALIBRATION GREEN WHITE CALIBRATION BLUE WHITE
CALIBRATION WHITE CURRENT HOURS POWER CONSUMPTION (AC 220V) MAINTENANCE
TIME:ALERT PERIOD MAINTENANCE TIME:ELAPSED TIME CLEAN ALL DATA
WIRELESS WIRELESS RESET
ERROR MESSAGES
0x82DD x
0x8211 x
0x82EC x
0x82BE x
0x8346 x 0x82BF x 0x82ED x 0x82C0 x 0x82C1 x 0x82C2 x 0x82C3 x 0x8217 x 0x82C9
x 0x82CA x 0x82CB x 0x82CC x 0x8200 x 0x8201 x 0x8202 x 0x8203 x 0x82C5 x
0x82DE x 0x82DF x 0x82E0 x 0x82C8 x 0x8212 x 0x8215 x
0x82EA x
0: Blackout
x
0-2 1: Hold
2: Stand Alone
0: Master DMX
x
0-2 1: Master NO DMX
2: Slave
0: Static
1: Color Macro
x
0-4 2: CCT
3: White Presets
4: Manual Color
0: R
1: G
2: B
3: W
4: GB
5: RB
6: RG
x
0-14 7: RGB
8: RW
9: GW
10: BW
11: RGW
12: RBW
13: GBW
14: RGBW
x
0-255 Default: 99
x
0-20 See pag.17
x
0-66 See pag.22
x
0-255 Default: 255
x
0-255 Default: 255
x
0-255 Default: 255
x
0-255 Default: 255
x
0-1
0: HB Mode 1: Studio Mode
x 125-255 Default: 255 x 125-255 Default: 255 x 125-255 Default: 255 x 125-255
Default: 255 x 125-255 Default: 255 x 125-255 Default: 255 x 125-255 Default:
255 x 125-255 Default: 255
0-65535
x
10-300 Default: 300
x
0-255
x
0-1
0: No 1: Yes
x
0-1
0: No 1: Yes
x
0-1
0: No 1: Yes
0: No error 0-2 1.Temperature too high
2.LED temperature sensor error
PROLIGHTS – EclDisplayCRMX FC
15
NOTE: the terms shown in BOLD indicates the default settings.
N° MENU
LEVEL 1
1 DMX ADDRESS 001 – 512
2 WIRELESS
OFF
ON
3 DMX MODE
BASIC
STANDARD EXTENDED BASIC 16 BIT
4 DIMMER CURVE LINEAR S-CURVE
SQUARE LAW INVERSE SQUARE LAW
LEVEL 2
LEVEL 3
DESCRIPTION Set address used for Fixture Enable/Disable the wireless card.
Set DMX chart for Main Fixture.
Select the dimmer curve.
5 DIMMER SPEED AUTO
FAST MEDIUM
6 LED FREQUENCY
7 DMX FAULT
SLOW 600 Hz 1200 Hz 2000 Hz 4000 Hz 6000 Hz 25 kHZ BLACKOUT HOLD STAND ALONE
Select the dimmer speed. Select LED PWM frequency.
Define the behaviour of fixture in case of DMX signal lost.
8 SPECIFIC PIDS OFF
RED
125-255
GREEN
125-255
BLUE
125-255
WARM WHITE
125-255
STUDIO RED
125-255
STUDIO GREEN
125-255
STUDIO BLUE
125-255
STUDIO WARM WHITE 125-255
9 INFORMATIONS DEVICE TIME
FIXTURE HOURS
(READ AND RESET)
CURRENT HOURS (READ AND RESET)
SOURCE HOURS
(READ AND RESET)
POWER ON CYCLE (READ AND RESET)
Check RDM Section.
To check the total working hours of the unit. To check the current working
hours of the unit. To see the total operating hours of the LED source. To see
the power cycles of the machine.
16
PROLIGHTS – EclDisplayCRMX FC
N° MENU
LEVEL 1
POWER CONSUMPTION SOFTWARE VERSION
10 STAND ALONE
DEVICE INFO DEVICE LABEL RDM UID MASTER/SLAVE
STATIC COLORS
CCT
LEVEL 2 MAINTENANCE TIME
LEVEL 3
ELAPSED TIME ALERT PERIOD
MASTER DMX
MASTER NO DMX
SLAVE
R G B W GB RB RG RGB RW GW BW RGW RBW GBW RGBW 2800K 3000K 3200K 3400K 3600K 3800K 4000K 4200K 4400K 4600K 4800K 5000K 5200K
0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255
DESCRIPTION To choose and reset unit maintenance warning hours.
Show actual power consumption.
View informations about software version.
View ID for the RDM control. Allow you to link and operating in synk multiple
units without a DMX console. Choose a unit to perform as the Master. This unit
must be the first unit in line; Set the successive units to be slave.
PROLIGHTS – EclDisplayCRMX FC
17
N° MENU
LEVEL 1
MANUAL
11 FACTORY
–
DEFAULT
LEVEL 2
5400K 5600K 6000K 6500K 7000K 8000K 9000K 10000K RED GREEN BLUE WARM WHITE
LEVEL 3
0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 – 255 0 –
255 0 – 255 0 – 255
DESCRIPTION
18
PROLIGHTS – EclDisplayCRMX FC
10 – DMX CHARTS
RDM Personality ID List
ID
DMX Mode
1
BASIC
2
STANDARD
3
EXTENDED
4
BASIC 16 BIT
Footprint 5CH 6CH 15CH 10CH
PARAMETER DIMMER
DIMMER FINE STROBE CCT
CROSSFADE RED
RED FINE GREEN
GREEN FINE BLUE
BLUE FINE WARM WHITE WARM WHITE FINE COLOR MACRO
CONTROL
BASIC 1
2 3 4 5
MODE
STANDARD EXTENDED
1
1
2
2
3
3
4
4
5
5
6
7
8
9
10
11
12
13
6
14
15
BASIC 16 BIT 1 2
3 4 5 6 7 8 9 10
Function Dimmer
8 bit value
From
To
0
255
Dimmer
16 bit value
From
To
0
65535
Note Default @ 0
Function
Open Strobe from Slow to Fast Open Pulse In from slow to fast Close Pulse Out
from slow to fast Open Random from slow to fast Open
Strobe
8 bit value
16 bit value
From
To
From
To
0
1
–
–
2
62
–
–
63
64
–
–
65
125
–
–
126
127
–
–
128
188
–
–
189
190
–
–
191
251
–
–
252
255
–
–
Note Default @ 255
PROLIGHTS – EclDisplayCRMX FC
19
From 2800 2900 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 7000 7100 7200 7300 7400 7500 7600 7700 7800
Function
To 2900 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 6100 6200 6300 6400 6500 6600 6700 6800 6900 7000 7100 7200 7300 7400 7500 7600 7700 7800 7900
CCT
8 bit value
16 bit value
From
To
From
To
0
4
0
910
4
7
910
1820
7
11
1820
2731
11
14
2731
3641
14
18
3641
4551
18
21
4551
5461
21
25
5461
6371
25
28
6371
7282
28
32
7282
8192
32
35
8192
9102
35
39
9102 10012
39
43
10012 10923
43
46
10923 11833
46
50
11833 12743
50
53
12743 13653
53
57
13653 14563
57
60
14563 15474
60
64
15474 16384
64
67
16384 17294
67
71
17294 18204
71
74
18204 19114
74
78
19114 20025
78
81
20025 20935
81
85
20935 21845
85
89
21845 22755
89
92
22755 23665
92
96
23665 24576
96
99
24576 25486
99
103
25486 26396
103
106
26396 27306
106
110
27306 28216
110
113
28216 29127
113
117
29127 30037
117
120
30037 30947
120
124
30947 31857
124
128
31857 32768
128
131
32768 33678
131
135
33678 34588
135
138
34588 35498
138
142
35498 36408
142
145
36408 37319
145
149
37319 38229
149
152
38229 39139
152
156
39139 40049
156
159
40049 40959
159
163
40959 41870
163
166
41870 42780
166
170
42780 43690
170
174
43690 44600
174
177
44600 45510
177
181
45510 46421
20
PROLIGHTS – EclDisplayCRMX FC
Note Default @ 0
7900 8000 8100 8200 8300 8400 8500 8600 8700 8800 8900 9000 9100 9200 9300 9400 9500 9600 9700 9800 9900
8000 8100 8200 8300 8400 8500 8600 8700 8800 8900 9000 9100 9200 9300 9400 9500 9600 9700 9800 9900 10000
181
184
46421 47331
184
188
47331 48241
188
191
48241 49151
191
195
49151 50061
195
198
50061 50972
198
202
50972 51882
202
205
51882 52792
205
209
52792 53702
209
213
53702 54613
213
216
54613 55523
216
220
55523 56433
220
223
56433 57343
223
227
57343 58253
227
230
58253 59164
230
234
59164 60074
234
237
60074 60984
237
241
60984 61894
241
244
61894 62804
244
248
62804 63715
248
251
63715 64625
251
255
64625 65535
Function Linear crossfade
Function 0 – 100%
Function 0 – 100%
Function 0 – 100%
Function 0 – 100%
Crossfade from CCT to Color
8 bit value
16 bit value
From
To
From
To
0
255
0
65535
8 bit value
From
To
0
255
Red
16 bit value
From
To
0
65535
8 bit value
From
To
0
255
Green
16 bit value
From
To
0
65535
8 bit value
From
To
0
255
Blue
16 bit value
From
To
0
65535
Warm White
8 bit value
16 bit value
From
To
From
To
0
255
0
65535
Note Default @ 255 / 65535
Note Default @ 255 / 65535
Note Default @ 255 / 65535
Note Default @ 255 / 65535
Note Default @ 255 / 65535
PROLIGHTS – EclDisplayCRMX FC
21
Function
No Function Red Green Blue Cyan Magenta Yellow Dirty White Alice Bllue Congo
Blue Dark Steel Blue Deep Lavender Lilac Ting Daylight Blue Flame Red Bastard
Amber Deep Orange Pale Gold Apricot Bright Blue Primary Green Special Lavender
Pale Lavender Deep Golden Amber Medium Blue Bright Pink Mauve Dark Green Lee
Green Dark Blue Light Blue Steel Blue Medium Blue-Green Peacock Blue Magenta
Dark Pink Middle Rose Light Salmon English Rose Light Rose Orange Deep Amber
Straw Light Amber Spring Yellow Dark Yellow Green Just Blue Sky Blue Lavender
Light Lavender Pink Carnation
22
Color Macro
8 bit value
16 bit value
From
To
From
To
0
1
–
–
2
3
–
–
4
5
–
–
6
7
–
–
8
9
–
–
10
11
–
–
12
13
–
–
14
15
–
–
16
17
–
–
18
19
–
–
20
21
–
–
22
23
–
–
24
25
–
–
26
27
–
–
28
29
–
–
30
31
–
–
32
33
–
–
34
35
–
–
36
37
–
–
38
39
–
–
40
41
–
–
42
43
–
–
44
45
–
–
46
47
–
–
48
49
–
–
50
51
–
–
52
53
–
–
54
55
–
–
56
57
–
–
58
59
–
–
60
61
–
–
62
63
–
–
64
65
–
–
66
67
–
–
68
69
–
–
70
71
–
–
72
73
–
–
74
75
–
–
76
77
–
–
78
79
–
–
80
81
–
–
82
83
–
–
84
85
–
–
86
87
–
–
88
89
–
–
90
91
–
–
92
93
–
–
94
95
–
–
96
97
–
–
98
99
–
–
100
101
–
–
Note
Default @ 255 Hold 3s to take function
PROLIGHTS – EclDisplayCRMX FC
Medium Pink Light Pink Sunset Red Dark Amber Gold Amber Medium Amber Fire Surprise Peach Straw Tint Medium Yellow Lee Minus Green Pale Gold Orange Deep Straw Rose Purple Deep Purple Soft Green Reserved 2800K 3000K 3200K 3400K 3600K 3800K 4000K 4200K 4400K 4600K 4800K 5000K 5200K 5400K 5600K 6000K 6500K 7000K 8000K 9000K 10000K Full ON
102
103
–
–
104
105
–
–
106
107
–
–
108
109
–
–
110
111
–
–
112
113
–
–
114
115
–
–
116
117
–
–
118
119
–
–
120
121
–
–
122
123
–
–
124
125
–
–
126
127
–
–
128
129
–
–
130
131
–
–
132
133
–
–
134
135
–
–
136
211
–
–
212
213
–
–
214
215
–
–
216
217
–
–
218
219
–
–
220
221
–
–
222
223
–
–
224
225
–
–
226
227
–
–
228
229
–
–
230
231
–
–
232
233
–
–
234
235
–
–
236
237
–
–
238
239
–
–
240
241
–
–
242
243
–
–
244
245
–
–
246
247
–
–
248
249
–
–
250
251
–
–
252
253
–
–
254
255
–
–
PROLIGHTS – EclDisplayCRMX FC
23
Function
No Functon DIMMER CURVE LINEAR DIMMER CURVE S-CURVE DIMMER CURVE SQUARE LAW
DIMMER CURVE INVERSE SQUARE LAW DIMMER SPEED AUTO DIMMER SPEED FAST DIMMER
SPEED MEDIUM DIMMER SPEED SLOW LED FREQUENCY 600HZ LED FREQUENCY 1200HZ LED
FREQUENCY 2000HZ LED FREQUENCY 4000HZ LED FREQUENCY 6000HZ LED FREQUENCY 25KHZ
STAND ALONE MASTER DMX STAND ALONE MASTER NO DMX STAND ALONE SLAVE DMX FAULT
HOLD DMX FAULT BLACKOUT DMX FAULT STAND ALONE
Reserved FACTORY DEFAULT OF CONTROL FUNCTIONS
Reserved
Control
8 bit value
From
To
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
251
252
253
254
255
16 bit value
From
To
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Note
Default @ 0 Hold 3s to take function
24
PROLIGHTS – EclDisplayCRMX FC
11 – ACCESSORIES INSTALLATION
OPTICS (CODES ECLDISPWASHL1530 / ECLDISPWASHL2550 / ECLDISPPRZL2040 – OPTIONAL) NOTE: the mounting procedure described below is the same for all lenses.
1
2
B A
Loosen the two marked knob of the ECLDISPLAY.
3
4
Insert the optic (2-A) and rotate it (2-B) so the marked grooves (3) of the optic coincides with the four marked flaps of the unit (4).
PROLIGHTS – EclDisplayCRMX FC
25
4
Loosen the two marked knobs on the top and lower of the ECLDISPLAY to rotate
the optics. 5
C
A
B
The marked lever in position A allows the locking of the blades. Rotating the lever to position B or C allows the release of the blades. This operation must be repeated for both levers on the frame system.
26
PROLIGHTS – EclDisplayCRMX FC
Fig. 10
BARNDOOR AND FILTER FRAME (CODE ECLDISPBDNFFB – OPTIONAL)
1
2
3
Insert the filter frame mounting the four marked Rotate the marked knob of the filter frame (2) and
screws into the holes provided on the optic.
and move the marked rod upwards (3).
4
6
5
Insert the holder from above throught the track Move the marked rod down (6).
(4). Then insert the barn door (5).
PROLIGHTS – EclDisplayCRMX FC
Fig. 11
27
ANTI-GLARE LOUVRE (CODE ECLDISPLOUVRE – OPTIONAL) NOTE: the rubber ring can
also be used to fix a filter with a maximum diameter of 79 mm.
1
Anti-glare louvre
Rubber ring
Insert the anti-glare louvre or a filter of maximum size of Ø79 mm into the
rubber ring. 2
Mount the anti-glare louvre with the rubber ring on the optic.
28
PROLIGHTS – EclDisplayCRMX FC
Fig. 12
GOBO HOLDER (CODE ECLDISPGOBOHIND – OPTIONAL)
1
2
BW / Colour
ID = Ø23 mm
B A
OD = Ø37.5 mm
3 mm
C
To mount the gobo remove the spring (1) from the gobo holder. Then insert the gobo following the sequence of image 2.
3
5
4
Loosen the two marked knobs of the optic (3). Then move the cover plate (4).
Insert the gobo holder into the slot provided on the optic (5).
PROLIGHTS – EclDisplayCRMX FC
Fig. 13
29
HALF SNOOT, FULL SNOOT (CODES ECLDISPHSNOOT, ECLDISPFSNOOT – OPTIONAL) 1
Loosen the three marked knob. Insert the half snoot on the optic and tighten the knobs in the egraved ring. 2
Loosen the three marked knob. Insert the full snoot on the optic and tighten the knobs in the egraved ring. Fig. 14
30
PROLIGHTS – EclDisplayCRMX FC
CEILING ADAPTER KIT (CODES ECLDISPCEILKIT, ECLDISPCEILFLG – OPTIONAL) 1
35 mm [1.4 in]
100 mm [3.9 in]
152 mm [6.0 in]
230 mm [9.1 in]
100 mm [3.9 in]
35 mm [1.4 in]
Ø180 mm [Ø7.1 in]
125 mm [4.9 in]
35 mm [1.4 in]
100 mm [3.9 in]
2
30 mm [1.2 in] 230 mm [9.1 in]
100 mm [3.9 in]
35 mm [1.4 in]
110 mm [4.3 in] Ø200 mm [7.9 in] Measurements for cuts on the panels (1) and of the ECLDISPCEILFLG (2).
PROLIGHTS – EclDisplayCRMX FC
31
3 CEILING
M4 screw
DETAIL
M6 screw
4
Mount the marked ceiling adapter kit on the ceiling by tightening the screws in the marked points (4). Fit the M6 screw to fix the projector (placed upside down) in the holes provided in the back housing (see detail). Fit the M4 screw to lock rotation.
32
PROLIGHTS – EclDisplayCRMX FC
5
6
M4 screw
DETAIL
The projector can be tilted with a range of tilt movement of -15° ÷ +15° (5). Tighten the two screws (see “DETAIL”) to lock the tilt movement. It is possible to decide the positioning height of the projector by using the marked plate (6). Tighten the M4 screw (6) to lock the vertical movement of the plate.
7
8
Mount the flange tightening the two marked screws (7) to complete the ceiling adapter kit. Fig. 15
PROLIGHTS – EclDisplayCRMX FC
33
12 – MAINTENANCE
MAINTENANCE AND CLEANING THE PRODUCT WARNING: Disconnect from the mains before
starting any maintenance work It is recommended to clean the front at regular
intervals, from impurities caused by dust, smoke, or other particles to ensure
that the light is radiated at maximum brightness. · For cleaning, disconnect
the main plug from the socket. Use a soft, clean cloth moistened with a
mild detergent. Then carefully wipe the part dry. For cleaning other housing
parts use only a soft, clean cloth. Never use a liquid, it might penetrate the
unit and cause damage to it. · The user must clean the product periodically to
maintain optimum performance and cooling. · The frequency of such maintenance
operations is to be performed according to various factors, such as the amount
of the use and the condition of the installation environment (air humidity,
presence of dust, salinity, etc.). It is recommended that the product is
subject to annual service by a qualified technician for special maintenance
involving at least the following procedures: · General cleaning of internal
parts. · For all the parts subject to friction, using lubricants specifically
supplied by PROLIGHTS. · General visual check of the internal components,
cabling, mechanical parts, etc. · Electrical, photometric and functional
checks; eventual repairs. · Cleaning the lenses. Only use neutral soap and
water to clean the lenses, then dry it carefully with a soft, non-abrasive
cloth. WARNING: the use of alcohol or any other detergent could damage the
lenses. · All other service operations on the product must be carried out by
PROLIGHTS, its approved service agents or trained and qualified personnel. ·
It is PROLIGHTS policy to apply the strictest possible calibration procedures
and use the best quality materials available to ensure optimum performance and
the longest possible component lifetimes. However, optical components are
subject to wear and tear over the life of the product, resulting in gradual
changes in colours over many thousands of hours of use. The extent of wear and
tear depends heavily on operating conditions and environment, so it is
impossible to specify precisely whether and to what extent performance will be
affected. However, you may eventually need to replace optical components if
their characteristics are affected by wear and tear after an extended period
of use and if you require fixtures to perform within very precise optical and
colour parameters. · Do not apply filters, lenses or other materials on lenses
or other optical components. Use only accessories approved by PROLIGHTS.
VISUAL CHECK OF PRODUCT HOUSING · The parts of the product cover/housing
should be checked for eventual damages and breaking
start at least every two months. In addition, especially the parts of the
front lens holder have to be checked mechanically (by means of movement by the
part) if it is firmly fastened to the fixture. If hint of a crack is found on
some plastic part, do not use the product until the damaged part will be
replaced. · Cracks or another damages of the cover/housing parts can be caused
by the product transportation or manipulation and also ageing process may
influence materials. · This checking is necessary for both fixed installations
and preparing product for renting. Any free moving parts inside of the
product, cracked cover/housing or any part of front lens not sitting properly
in place need to be immediately replaced.
34
PROLIGHTS – EclDisplayCRMX FC
TROUBLESHOOTING
Problems
Possible causes
Checks and remedies
Product doesn’t power ON · No power to the · Check that power is switched ON and cables are
product
plugged in.
Product reset correctly but does not respond correctly to the contoller.
· Bad signal connection
· Signal connection not terminated
· Inspect connections and cables. Fix eventual bad connections. Repair or
replace damaged cables.
· Insert DMX termination plug in signal output socket of the last product on
the signal line.
Timeout error after fixture reset.
Mechanical effect loses position
· Incorrect addressing of · Check the product address and control settings the product
· One of the product is · Unplug the XLR in and out connectors and connect
defective and is corrupt- them directly together to bypass one product at a
ing the signal transmis- time until normal operation is regained. Once found
sion on the signal line
the error, have that fixture serviced by a qualified
technician.
· One or more hardware · Check product stored error messages for more
· components requires
information. Contact PROLIGHTS Service or an
· mechanical adjustments authorized service partner.
· Mechanical hardware · Check product stored error messages for more
require cleaning, adjust- information. Contact PROLIGHTS Service or an
ment or lubrification
authorized service partner.
Light output turn OFF Intermittently
General low light intensity
· Fixture is too hot
· Check product stored error messages. · Allow product to cool. · Clean the product and airflow filters. · Reduce ambient temperature.
· Hardware failure (tem- · Check product stored error messages for more
perature sensor, fans, Light source…)
information. Contact. PROLIGHTS Service or an authorized service partner.
· Dirty lens assembly
· Clean the fixture regularly.
· Dirty or damaged filters · Install lens assembly properly.
Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.
PROLIGHTS – EclDisplayCRMX FC
35
Note
Note
PROLIGHTS is a trademark of MUSIC & LIGHTS S.r.l. musiclights.it
Via A.Olivetti snc 04026 – Minturno (LT) ITALY Tel: +39 0771 72190
prolights.it support@prolights.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>