PROLiGHTS Flood150FC 150W Full Colour RGB WarmWhite Asymmetric LED floodlight User Manual

: June 13, 2024
: PROLIGHTS

Table of Contents

PROLiGHTS Flood150FC 150W Full Color RGB WarmWhite Asymmetric LED
Product Information
Product Usage Instructions
SAFETY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROLiGHTS Flood150FC 150W Full Color RGB WarmWhite Asymmetric LED

floodlight

Product Information

Product Name: EclExpo Flood150FC
Product Type: LED floodlight
Power: 150W
Color: Full Color RGB + Warm White
Design: Asymmetrical
Manufacturer: PROLIGHTS

Product Usage Instructions

Thank you for choosing the PROLIGHTS EclExpo Flood150FC LED floodlight. This product has been designed in Italy to meet quality and performance requirements for professionals.

Please note that this product is meant for professional use only. Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be a source of danger.

Before using the EclExpo Flood150FC, please read and understand the user manual provided. You can download the user manual from the website www.prolights.it or inquire with the official PROLIGHTS distributors in your territory ( https://www.prolights.it/sales_network.html ).

Ensure that you comply with the respective applicable national accident prevention rules and regulations for commercial use of this equipment.

When installing or servicing the product, observe the safety instructions provided in the user manual.
The minimum distance of illuminated objects should be 0.5m.

This product comes with a warranty. Please refer to the user manual for details on the warranty.

To preserve the environment, please dispose/recycle this product at the end of its life according to the local regulations on Electrical and Electronic Equipment (WEEE).

Please ensure that this device does not cause harmful interference and accepts any interference received, as per the instructions provided in the user manual.

For further information, technical documentation, and updates, visit the download area of the product page on the PROLIGHTS website.

For any additional information or assistance, please contact the official PROLIGHTS distributors in your territory.

Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident prevention rules and regulations.
Features, specifications and appearance are subject to change without notice. Music & Lights S.r.l. and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the official PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can find a broad set of always updated technical documentation: specifications, user manual, technical drawings, photometrics, personalities, fixture firmware updates.

Visit the download area of the product page

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its affiliates, and subsidiaries. PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc – 04026 – Minturno (LT) ITALY.

SAFETY INFORMATION

WARNING!

See https://www.prolights.it/product/ECLEXPOFL150FC#download for installation instructions.
Please read carefully the instruction reported in this section before installing, powering, operating or servicing the product and observe the indications also for its future handling.
This unit is not for household and residential use, only professional applications.

Connection to mains supply

The Connection to the mains supply must be carried out by a qualified electrical installer.
Use only AC supplies 100-240V 50-60 Hz, the fixture must be electrically connected to ground (earth).
Select the cable cross-section in according with the maximum current draw of the product and the possible number of products connected at the same power line.
The AC mains power distribution circuit must be equipped with magnetic+residual current circuit breaker protection.
Do not connect it to a dimmer system; doing so may damage the product.

Protection and Warning against electrical shock

Do not remove any cover from the product, always disconnect the product from AC power before servicing.
Ensure that the fixture is electrically connected to ground (earth). And use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fault) protection.
Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices.
Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other components are damaged, defective, deformed or showing signs of overheating.
Do not reapply power until repairs have been completed.
Refer any service operation not described in this manual to PROLIGHTS Service team or an authorized PROLIGHTS service center.

Installation

Make sure that all visible parts of the product are in good visible condition before its use or installation.
Make sure the point of anchorage is stable before positioning the projector.
When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety cable that is approved as a safety attachment for the weight of the fixture to the attachment point on the main frame of the product. ln case the safety cable, enter in action, it needs to be replaced with a new one.
Install the product only in well ventilated places.
For non temporary installations, ensure that the fixture is securely fastened to a loadbearing surface with suitable corrosion-resistant hardware.
For a temporary installation with clamps, ensure that the quarter-turn fastener and/or screws are turned fully, and secured with a suitable safety cable.

Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 0,5 meters (1,64 ft) from the lens of the projector.

Max operating ambient temperature (Ta)

Do not operate the fixture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
Minimum operating ambient temperature (Ta)
Do not operate the fixture if the ambient temperature (Ta) is below -10 °C (14 °F).

Protection from burns and fire

The exterior of the fixture becomes hot during use. Avoid contact by persons and materials.
Ensure that there is free and unobstructed airflow around the fixture.
Keep flammable materials well away from the fixture
Do not expose the front glass to sunlight or any other strong light source from any angle.
Lenses can focus the sun’s rays inside the fixture, creating a potential fire hazard.
Do not attempt to bypass thermostatic switches or fuses.

Indoor use

This product is designed for indoor and dry environments.
Do not use in wet location and do not expose the fixture to rain or moisture.
Never use the fixture in places subject to vibrations or bumps.
Make certain that no inflammable liquids, water or metal objects enter the fixture.
Excessive dust, smoke fluid, and particle build up degrades performance, causes overheating and will damage the fixture.
Damages caused by inadequate cleaning or maintenance are not covered by the product warranty.

Temperature of the external surface

The surface of the fixture can reach up to 60 °C (140 °F) during operation. Avoid contact with people and materials.

Maintenance

Warning! Disconnect the fixture from AC mains power and allow to cool for at least 10 minutes before handling.
Only technicians who are authorized by PROLIGHTS or Authorised service partners are permitted to open the fixture.
Users may carry out external cleaning, following the warnings and instructions provided, but any service operation not described in this manual must be referred to a qualified service technician.
Important! Excessive dust, smoke fluid, and particle build up degrades performance, causes overheating and will damage the fixture. Damages caused by inadequate cleaning or maintenance is not covered by the product warranty.

Photobiological safety

This device emits potentially dangerous optical radiation and is identified in the category of Risk Group 1 according to EN 62471.
Do not stare at the operating light source
Do not look directly at the LED source during operation. It can be harmful to the eyes and skin.
During Installation, operation and maintenance, be prepared for the fixture to light and move suddenly when connected to power.

Disposal

This product is supplied in compliance with European Directive 2012/19/EU – Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/ recycle this product at the end of its life according to the local regulation.

The products to which this manual refers comply with:

2014/35/EU – Safety of electrical equipment supplied at low voltage (LVD).
2014/30/EU – Electromagnetic Compatibility (EMC).
2011/65/EU – Restriction of the use of certain hazardous substances (RoHS).

The products to which this manual refers comply with:

UL 1573 + CSA C22.2 No. 166 – Stage and Studio Luminaires and Connector Strips.
UL 1012 + CSA C22.2 No. 107.1 – Standard for power units other than class 2.

FCC Compliance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.

Other approvals

PROLIGHTS is a trademark of MUSIC & LIGHTS S.r.l.
musiclights.it

Via A.Olivetti snc
04026 – Minturno (LT) ITALY
Tel: +39 0771 72190

prolights.it
support@prolights.it