PROLIGHTS EclExpo Flood150VW 171234 150W Asymmetric LED Floodlight User Manual
- June 13, 2024
- PROLIGHTS
Table of Contents
- EclExpo Flood150VW 171234 150W Asymmetric LED Floodlight
- Product Information:
- Product Usage Instructions:
- 1 – Packaging
- 2 – Technical Drawing
- 3 – Installation
- 4 – Connection to the Mains Supply
- 5 – Start Up
- 6 – Product Overview
- 7 – DMX Connection
- 8 – Control Panel
- 9 – Menu Structure
- 10 – RDM Functions
- 11 – Shortcuts
- 12 – Errors
- 13 – DMX Charts
- 14 – Accessories Installation
- 15 – Maintenance
- Safety Information:
EclExpo Flood150VW 171234 150W Asymmetric LED Floodlight
Product Information:
Product Name: EclExpo Flood150VW
Description: 150W asymmetric LED floodlight with Variable
White CCT 2,700K – 6,500K
User Manual: REV.01-08/23
Language: English version
Product Usage Instructions:
1 – Packaging
Package Content:
- The EclExpo Flood150VW LED floodlight
Optional Accessories:
- Filter Frame (CODE ECLEXPOFL150FFBK)
- Barn Door (CODE ECLEXPOFL150BDBK)
- CRMX Wireless Kit (CODE ECLEXPOFL150WKBK)
2 – Technical Drawing
The technical drawing is not provided in the user manual.
3 – Installation
Mounting:
To install the EclExpo Flood150VW LED floodlight, follow the
provided mounting instructions.
4 – Connection to the Mains Supply
To connect the EclExpo Flood150VW LED floodlight to the mains
supply, follow the provided instructions for safe and proper
connection.
5 – Start Up
Connect and Disconnect Power from the Product:
To power on or off the EclExpo Flood150VW LED floodlight, follow
the provided instructions for safe power connection and
disconnection.
6 – Product Overview
No specific information is provided in the user manual regarding
the product overview.
7 – DMX Connection
Reset the Receiver:
Refer to the user manual for instructions on resetting the
receiver.
WDMX to DMX (RX):
Refer to the user manual for instructions on connecting WDMX to
DMX (RX).
8 – Control Panel
Display and Buttons Layout:
The user manual provides information about the display and
buttons layout of the EclExpo Flood150VW LED floodlight. Refer to
the manual for details.
Rotatory Knob Layout:
The user manual provides information about the rotatory knob
layout of the EclExpo Flood150VW LED floodlight. Refer to the
manual for details.
9 – Menu Structure
The user manual provides a menu structure guide for navigating
the settings and options of the EclExpo Flood150VW LED floodlight.
Refer to the manual for details.
10 – RDM Functions
The user manual provides information on RDM functions. Refer to
the manual for details.
11 – Shortcuts
The user manual provides information on shortcuts available for
quick access to specific functions or settings. Refer to the manual
for details.
12 – Errors
The user manual provides information on common errors and
troubleshooting steps. Refer to the manual for details.
13 – DMX Charts
The user manual includes DMX charts for reference. Refer to the
manual for details.
14 – Accessories Installation
Filter Frame (CODE ECLEXPOFL150FFBK – Optional):
Refer to the user manual for instructions on installing the
optional Filter Frame accessory.
Barn Door (CODE ECLEXPOFL150BDBK – Optional):
Refer to the user manual for instructions on installing the
optional Barn Door accessory.
CRMX Wireless Kit (CODE ECLEXPOFL150WKBK – Optional):
Refer to the user manual for instructions on installing the
optional CRMX Wireless Kit accessory.
15 – Maintenance
Maintenance and Cleaning the Product:
To maintain and clean the EclExpo Flood150VW LED floodlight,
follow the provided instructions in the user manual.
Replacing the Fuse:
If the fuse needs replacement, refer to the user manual for
instructions on replacing the fuse.
Visual Check of Product Housing:
Perform a visual check of the product housing as instructed in
the user manual.
Troubleshooting:
If you encounter any issues, refer to the troubleshooting
section in the user manual for possible solutions.
Safety Information:
The user manual contains important safety information that
should be followed when handling, operating, or servicing the
product. Ensure to read and observe these indications for safe
usage and future handling of the product.
Note: This unit is intended for professional applications
and not for household or residential use.
Caution: Keep at least 0.5 meters (1.64 ft) distance from
the lens of the projector to avoid any potential risks.
Product Warranty: The user manual does not provide
specific warranty information. Please refer to the warranty
documentation provided by PROLIGHTS.
Environmental Disposal: To preserve the environment,
dispose or recycle this product according to the local regulations
at the end of its life.
Interference: This device complies with Part 15 of the
FCC Rules. It may not cause harmful interference and must accept
any interference received, including interference that may cause
undesired operation.
Other Approvals: The user manual does not specify any
additional approvals for the product.
EclExpo Flood150VW
150W asymmetric LED floodlight, with Variable White CCT 2,700K – 6,500K
USER MANUAL
REV.01-08/23
English version
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet
quality and performance requirements for professionals and designed and
manufactured for the use and application as shown in this document. Any other
use, if not expressly indicated, could compromise the good condition/operation
of the product and/or be a source of danger. This product is meant for
professional use. Therefore, commercial use of this equipment is subject to
the respectively applicable national accident prevention rules and
regulations. Features, specifications and appearance are subject to change
without notice. Music & Lights S.r.l. and all affiliated companies disclaim
liability for any injury, damage, direct or indirect loss, consequential or
economic loss or any other loss occasioned by the use of, inability to use or
reliance on the information contained in this document. Product user manual
can be downloaded from the website www.prolights.it , or can be inquired to
the official PROLIGHTS distributors of your territory
(https://www.prolights.it/sales_network.html). Scanning the below QR Code, you
will access the download area of the product page, where you can find a broad
set of always updated technical documentation: specifications, user manual,
technical drawings, photometrics, personalities, fixture firmware updates.
Visit the download area of the product page
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document
pertaining to PROLIGHTS services or PROLIGHTS product are trademarks OWNED or
licensed by Music & Lights S.r.l., its affiliates, and subsidiaries. PROLIGHTS
is a registered trademark by Music & Lights S.r.l. All right reserved. Music &
Lights Via A. Olivetti, snc 04026 – Minturno (LT) ITALY.
INDEX
SAFETY INFORMATION
02
1 – PACKAGING
05
PACKAGE CONTENT ……………………………………………………………………………………….. 05
OPTIONAL ACCESSORIES………………………………………………………………………………… 05
2 – TECHNICAL DRAWING
05
3 – INSTALLATION
06
MOUNTING…………………………………………………………………………………………………….. 06
4 – CONNECTION TO THE MAINS SUPPLY
07
5 – START UP
07
CONNECT AND DISCONNECT POWER FROM THE PRODUCT……………………………. 07
6 – PRODUCT OVERVIEW
08
7 – DMX CONNECTION
09
CONNECTION OF THE CONTROL SIGNAL: DMX LINE ………………………………………. 09 INSTRUCTIONS
FOR A RELIABLE DMX CONNECTION ……………………………………….. 09 CONNECTION DAISY
CHAIN……………………………………………………………………………. 09 CONNECTION OF THE DMX
LINE…………………………………………………………………….. 09 CONSTRUCTION OF THE DMX TERMINATION
………………………………………………….. 10 DMX ADDRESSING …………………………………………………………………………………………..
10 OPERATION AS A WIRELESS TRANSMITTER ………………………………………………………. 10 Unlinking the
transmitter …………………………………………………………………………………… 11 DMX TO WDMX
(TX)………………………………………………………………………………………… 11 OPERATION AS A WIRELESS
RECEIVER……………………………………………………………… 11
Reset the receiver …………………………………………………………………………………………….. 11 WDMX TO DMX
(RX)………………………………………………………………………………………… 11
8 – CONTROL PANEL
12
DISPLAY AND BUTTONS LAYOUT……………………………………………………………………… 12 ROTATORY KNOB LAYOUT ………………………………………………………………………………. 12
9 – MENU STRUCTURE
13
10 – RDM FUNCTIONS
16
11 – SHORTCUTS
18
12 – ERRORS
18
13 – DMX CHARTS
19
14 – ACCESSORIES INSTALLATION
22
FILTER FRAME (CODE ECLEXPOFL150FFBK – OPTIONAL) …………………………………… 22 BARNDOOR (CODE ECLEXPOFL150BDBK – OPTIONAL)…………………………………….. 23 CRMX WIRELESS KIT (CODE ECLEXPOFL150WKBK – OPTIONAL) ……………………….. 24
15 – MAINTENANCE
26
MAINTENANCE AND CLEANING THE PRODUCT……………………………………………….. 26 REPLACING THE FUSE……………………………………………………………………………………… 26 VISUAL CHECK OF PRODUCT HOUSING …………………………………………………………… 26 TROUBLESHOOTING……………………………………………………………………………………….. 27
PROLIGHTS – EclExpo Flood150VW
01
SAFETY INFORMATION
WARNING! · See https://www.prolights.it/product/ECLEXPOFL150VW#download for
installation in-
structions. · Please read carefully the instruction reported in this section
before installing, power-
ing, operating or servicing the product and observe the indications also for
its future handling.
This unit is not for household and residential use, only professional
applications.
Connection to mains supply · The Connection to the mains supply must be
carried out by a qualified electrical
installer. · Use only AC supplies 100-240V 50-60 Hz, the fixture must be
electrically connected
to ground (earth). · Select the cable cross section in according with the
maximum current draw of the
product and the possible number of products connected at the same power line.
· The AC mains power distribution circuit must be equipped with
magnetic+residual
current circuit breaker protection. · Do not connect it to a dimmer system;
doing so may damage the product.
Protection and Warning against electrical shock · Do not remove any cover from
the product, always disconnect the product from AC
power before servicing. · Ensure that the fixture is electrically connected to
ground (earth). And use only a
source of AC power that complies with local building and electrical codes and
has both overload and ground-fault (earth-fault) protection. · Before using
the fixture, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected
devices. · Isolate the fixture from power immediately if the power plug or any
seal, cover, cable, or other components are damaged, defective, deformed or
showing signs of overheating. · Do not reapply power until repairs have been
completed. · Refer any service operation not described in this manual to
PROLIGHTS Service team or an authorized PROLIGHTS service center.
Installation · Make sure that all visible parts of the product are in good
visible condition before its
use or installation. · Make sure the point of anchorage is stable before
positioning the projector. · When suspending the fixture above ground level,
secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety
attachment for the weight of the fixture to the attachment point on the main
frame of the product. ln case the safety cable, enter in action, it needs to
be replaced with a new one. · Install the product only in well ventilated
places. · For non temporary installations, ensure that the fixture is securely
fastened to a loadbearing surface with suitable corrosionresistant hardware. ·
For a temporary installation with clamps, ensure that the quarter-turn
fastener and/or screws are turned fully, and secured with a suitable safety
cable.
02
PROLIGHTS – EclExpo Flood150VW
0,5 m
Ta 45°C Ta -10°C
Tc 60°C
Minimum distance of illuminated objects · The projector needs to be positioned
so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
Max operating ambient temperature (Ta) · Do not operate the fixture if the
ambient temperature (Ta) exceeds 45 °C (113 °F).
Minimum operating ambient temperature (Ta) · Do not operate the fixture if the
ambient temperature (Ta) is below -10 °C (14 °F).
Protection from burns and fire · The exterior of the fixture becomes hot
during use. Avoid contact by persons and
materials. · Ensure that there is free and unobstructed airflow around the
fixture. · Keep flammable materials well away from the fixture · Do not expose
the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the fixture, creating a potential
fire hazard. · Do not attempt to bypass thermostatic switches or fuses.
Indoor use · This product is designed for indoor and dry environments. · Do
not use in wet location and do not expose the fixture to rain or moisture. ·
Never use the fixture in places subject to vibrations or bumps. · Make certain
that no inflammable liquids, water or metal objects enter the fixture. ·
Excessive dust, smoke fluid, and particle build up degrades performance,
causes
overheating and will damage the fixture. · Damages caused by inadequate
cleaning or maintenance are not covered by the
product warranty.
Temperature of the external surface · The surface of the fixture can reach up
to 60 °C (140 °F) during operation. Avoid
contact with people and materials.
Maintenance · Warning! Disconnect the fixture from AC mains power and allow to
cool for at least
10 minutes before handling. · Only technicians who are authorized by PROLIGHTS
or Authorised service partners
are permitted to open the fixture. · Users may carry out external cleaning,
following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred
to a qualified service technician. · Important! Excessive dust, smoke fluid,
and particle build up degrades performance, causes overheating and will damage
the fixture. Damages caused by inadequate cleaning or maintenance is not
covered by the product warranty.
Photobiological safety · This device emits potentially dangerous optical
radiation and is identified in the cat-
egory of Risk Group 1 according to EN 62471.
Do not stare at the operating light source · Do not look directly at the LED
source during operation. It can be harmful to the eyes
and skin. · During Installation, operation and maintenance, be prepared for
the fixture to light
and move suddenly when connected to power.
PROLIGHTS – EclExpo Flood150VW
03
Disposal · This product is supplied in compliance with European Directive
2012/19/EU Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please
dispose/ recycle this product at the end of its life according to the local
regulation.
The products to which this manual refers comply with: · 2014/35/EU – Safety of
electrical equipment supplied at low voltage (LVD). · 2014/30/EU –
Electromagnetic Compatibility (EMC). · 2011/65/EU – Restriction of the use of
certain hazardous substances (RoHS). · 2014/53/EU – Radio Equipment Directive
(RED).
The products to which this manual refers comply with: · UL 1573 + CSA C22.2
No. 166 – Stage and Studio Luminaires and Connector Strips. · UL 1012 + CSA
C22.2 No. 107.1 – Standard for power units other than class 2.
FCC Compliance: · This device complies with Part 15 of the FCC Rules.
Operation is subject to the fol-
lowing two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may
cause undesired operation.
Other approvals
04
PROLIGHTS – EclExpo Flood150VW
1 – PACKAGING
PACKAGE CONTENT · 1 x ECLEXPOFL150VW · 1 x 1,5 meters power cable (BARE END –
SEETRONIC POWERCON TRUE1 IP65) · 1 x User Manual
OPTIONAL ACCESSORIES · FCLEXPOFL150:Flight case for 6 pcs of ECLEXPOFL150
series · ECLEXPOFL150FFBK:Filter frame for ECLEXPOFL150, black ·
ECLEXPOFL150BDBK:Barn door 8 directional flaps to adjust the light beam for
ECLEXPOFL150, black · ECLEXPOFL150WKBK:CRMX Timo Fx kit for ECLEXPOFL150,
black · SPGM10:28mm spigot for fixtures, M10 bolt · UPBOXPRO:Firmware uploader
kit, USB IN, 5-pin XLR DMX OUT connector · UPBOX1UP5:Firmware uploader kit,
USB IN, 5pin XLR DMX OUT, USB OUT · SPGM12:28mm spigot for fixtures, M12 bolt
· RSR0630B:Steel security cable for hanging bodies, inox steel shackle, L=60
cm, black · 9533FXWL03:Ass. 3×2.5mm TH07 cable, SCHUKO plug, MENAC3FXW socket,
L.3m · 9513FXWL03:Ass. 3×2.5mm TH07 cable, 16A 3p 230V CEE plug, MENAC3FXW
socket, L.3 m · 958225L03:3×2.5mm TH07 Cable, 16A 3p PwCon MXW, 16A 3p PwCon
FXW, L. 3m · TOUR53415L03:Dmx cable HC5340. CANC5MXX XLR 5p->CANC5FXX XLR (f)
5p, L.3m · LRLUNA: Single Universe DMX transceiver with Bluetooth · C6002B:
Slim aluminum clamp, 200kg loading, 48-51mm tubes, M10 bolt, Black
2 – TECHNICAL DRAWING
110 mm [4.3 in]
Ø246 mm [9.7 in]
273 mm [10.8 in] 106 mm [4.2 in] 295 mm [11.6 in]
283 mm [11.1 in]
176 mm [6.9 in]
Weight: 3,2 kg / 7,05 lbs
PROLIGHTS – EclExpo Flood150VW
179 mm [7.0 in] Fig. 01
05
3 – INSTALLATION
MOUNTING Check that the supporting structure can safely bear the weight of all installed fixtures, clamps, cables, auxiliary equipment, etc. and complies with locally applicable regulations. When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety wire that is approved as a safety attachment for the weight of the fixture to an anchor point on the product main frame. Do not use removable parts or weak anchors for secondary attachment. Warning! When clamping the fixture to a truss or other structure at any angle, use clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
C6002 clamp
RSR0630A/B steel security cable
Fig. 02
06
283 mm [11.1 in] 110 mm [4.3 in] 25 mm [1.0 in]
35 mm [1.4 in]
Ø6 mm [0.2 in]
Ø13 mm [0.5 in] 229 mm [9.0 in]
PROLIGHTS – EclExpo Flood150VW
4 – CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the fixture must be earthed! The
product is equipped with auto-switching power supply that automatically
adjusts to any 50-60Hz AC power source from 100-240 Volts. If you need to
install a power plug on the power cable to allow connection to power outlets,
install a grounding-type (earthed) plug, following the plug manufacturer’s
instructions. If you have any doubts about proper installation, consult a
qualified electrician. T max power consumption is 170W.
Core (EU) Brown Blue
Yellow+green
Core (US) Black White Green
Connection Live
Neutral Earth
Plug terminal marking L N
5 – START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT To apply and disconnect power to
the product: · Check that the product is installed and secured as indicated in
the Safety Informations, and that
personal safety will not be put at risk when the fixture lights up. · Connect
the power connector into the Mains input socket (100-240 VAC-50/60 Hz). · The
product is then ready for its operations and can be controlled through the
available input sig-
nals on board. · To disconnect power from the product, disconnect the Mains
from the socket. · In case you wish to run the product through an external
battery, then connect the product to an
external battery (24-36V) into the dedicated XLR4p socket; to disconnect
power, disconnect the Battery from the socket.
PROLIGHTS – EclExpo Flood150VW
07
6 – PRODUCT OVERVIEW
1. BRACKET. 2. KNOB for bracket. 3. POWER IN: for connection to the Mains
100-240V~/50-60Hz. 4. POWER OUT: power output for connection of multiple units
in series. 5. MAIN FUSE HOLDER: replace a burnt-out fuse by one of the same
type only (T5A 250V). 6. ROTATORY KNOBS for product stand alone control
operations. 7. USER INTERFACE with display and buttons for access to the
control panel functions. 8. DMX IN (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4
N/C, 5 N/C. 9. DMX OUT (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.
10. ANTENNA of Wireless DMX Receiver internal module.
3
6
1
6
8
2 08
45
7
9 10 2
Fig. 03
PROLIGHTS – EclExpo Flood150VW
7 – DMX CONNECTION
CONNECTION OF THE CONTROL SIGNAL: DMX LINE The product has XLR sockets for DMX
input and output. The default pin-out on both socket is as the following
diagram:
DMX – INPUT XLR plug
Pin1 : GND – Shield Pin2 : – Signal Pin3 : + Signal Pin4 : N/C Pin5 : N/C
DMX – OUTPUT XLR socket
Fig. 04
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION Use shielded twisted-pair cable
designed for RS-485 devices: standard microphone cable cannot transmit control
data reliably over long runs. 24 AWG cable is suitable for runs up to 300
meters (1000 ft). Heavier gauge cable and/or an amplifier is recommended for
longer runs. To split the data link into branches, use splitter-amplifiers in
the connection line. Do not overload the link. Up to 32 devices may be
connected on a serial link.
CONNECTION DAISY CHAIN Connect the DMX data output from the DMX source to the
product DMX input (male connector XLR)
socket. Run the data link from the product XLR output (female connector XLR)
socket to the DMX input of the next fixture.
Terminate the data link by connecting a 120 Ohm signal termination. If a
splitter is used, terminate
each branch of the link. Install a DMX termination plug on the last fixture on
the link.
CONNECTION OF THE DMX LINE DMX connection employs standard XLR connectors. Use
shielded pair-twisted cables with 120 im-
pedance and low capacity.
The following diagram shows the connection mode:
DMX Address: 33
DMX Address: 48
DMX Address: 63
DMX Address: 78
DMX IN DMX OUT
DMX IN DMX OUT
DMX IN DMX OUT
DMX IN DMX OUT
. . . . . . . . . . . . . . . . . . . . . . . .
DMX512 Controller
Fig. 05 – Example 15 DMX channels configuration
PROLIGHTS – EclExpo Flood150VW
09
CONSTRUCTION OF THE DMX TERMINATION The termination is prepared by soldering a 120 1/4 W resistor between pins 2 and 3 of the male XLR connector, as shown in figure.
4
Example: 5 pin XLR connector
Fig. 06
DMX ADDRESSING In order to start controlling the product via DMX, the first
step is to select a DMX address, also known as the start channel, this is the
first channel used to receive instructions from a DMX controller. If you wish
to control the product individually, it is necessary to assign a different
starting address channel to each fixture. The number of channels occupied from
the product depends on the DMX mode selected, so always verify the DMX Mode in
the MENU before start addressing. If you assign two fixtures the same address,
they will be executing the same behaviour. Selecting the same address to
multiple fixtures can be useful for diagnostic purposes and symmetrical
control. DMX addressing is limited to make it impossible to set the DMX
address so high that you are left without enough control channels for the
product. To set the fixture’s DMX address: 1. Press MENU to open the main
menu. 2. Reach the addressing menu, then select the DMX ADDRESS settings. 3.
Select the address from 1 to 512 using the navigation arrows/buttons and
confirm by pressing
ENTER. 4. Press Menu to exit and return to the Home screen. The product DMX
address, as well as other possible user settings through the MENU, can also be
set when the product is disconnected from the Main through the internal
battery-backup. All that is needed is to press and hold the button ENTER to
momentarily enable the display and enter in the settings. Once the required
operations have been executed, the display will switch off again after few
seconds of being inactive.
OPERATION AS A WIRELESS TRANSMITTER ECLEXPOFL150VW can be used as wireless
trasmitter for transmitt at different wireless receivers DMX signal. To use
ECLEXPOFL150VW as wireless transmitter, please follow the procedure below: 1.
Push MENU button untill you show CONNECT on display, then press ENTER button
to confirm. 2. Use UP/DOWN buttons for select Wireless, then press ENTER to
confirm. 3. Push ENTER button on WDMX ON/OFF function and enable it to ON. 4.
Select WDMX mode and set it on Transmitter (please note that WDMX mode will be
available only
if WDMX ON/OFF is set to ON).
5. Ensure that the receiver units are not connected to any other transmitter.
Please refer to “Reset the
receiver” paragraph. 6. Enable TX LINK to ON to link transmitter to receivers
(please note that TX LINK will be avaible only
if WDMX mode is set to Transmitter).
10
PROLIGHTS – EclExpo Flood150VW
· The transmitter scans for all unlinked receivers for a period of about 5
seconds. · If the connection fails, check the position of the receiver. · The
wireless icon on the receiver display indicates the received signal strength.
Unlinking the transmitter Follow the procedure below to unlink the transmitter
from all receivers connected with the unit. 1. Push MENU button untill you
show CONNECT on display, then press ENTER button to confirm. 2. Use UP/DOWN
buttons for select Wireless, then press ENTER to confirm. 3. Enable TX UNLINK
to ON 8 (please note that TX UNLINK will be avaible only if WDMX mode is set
to Transmitter). · All connected receivers will be unlinked.
DMX TO WDMX (TX) This function enable or disable the transmission throught
wireless of the DMX signal from the transmitter side to the receiver.
OPERATION AS A WIRELESS RECEIVER ECLEXPOFL150VW can be used as wireless
receiver connected to a wireless transmitter. To use ECLEXPOFL150VW as
wireless receiver, please follow the procedure below: 1. Push MENU button
untill you show CONNECT on display, then press ENTER button to confirm. 2. Use
UP/DOWN buttons for select Wireless, then press ENTER to confirm. 3. Push
ENTER button on WDMX ON/OFF function and enable it to ON. 4. Select WDMX mode
and set it on Receiver (please note that WDMX mode will be available only if
WDMX ON/OFF is set to ON). 5. Enable RX RESET to ON to reset the receiver
(please note that RX RESET will be avaible only if
WDMX mode is set to Receiver). 6. On the transmitter, enable TX LINK to ON to
link transmitter to the receivers. 7. If the connection is successful and DMX
input is available the display the display on the receiver
unit will shows the DMX address. If DMX signal is not available, the display
will shows “No signal” but keeps the transmitter linked. 8. If the connection
fails, check the position of the receiver. 9. The wireless icon on the
receiver display indicates the received signal strength.
Reset the receiver Follow the procedure below to reset the receiver. 1. Push
MENU button untill you show CONNECT on display, then press ENTER button to
confirm. 2. Use UP/DOWN buttons for select Wireless, then press ENTER to
confirm. 3. Enable RX RESET to ON. · The wireless icon on the receiver display
indicates the received signal strength.
WDMX TO DMX (RX) This function enable or disable the retransmission of the
wireless DMX signal received throught the DMX port on the receiver side.
PROLIGHTS – EclExpo Flood150VW
11
8 – CONTROL PANEL
The product has a display and buttons for access to the control panel
functions.
Fig. 07
DISPLAY AND BUTTONS LAYOUT · The product has a display and buttons for access
to the control panel functions. · MENU: Used to access the menu tree or to
return a previous menu window. · UP: Browse upwards through the menu list and
increases the numeric value displayed. · DOWN: Browse downwards through the
menu list and decreases the numeric value displayed. · ENTER: Used to confirm
the current menu or confirm the current function value or option within a
menu.
ROTATORY KNOB LAYOUT The product is equipped with rotatory knobs for manual
control of the product, those are enabled only in Stand Alone mode and they
enable access to control certain attributes according to the selected STAND
ALONE mode asindicated in the following chapter.
12
PROLIGHTS – EclExpo Flood150VW
9 – MENU STRUCTURE
The following chart describes the MENU tree of the product, the terms shown in
BOLD indicates the default settings.
1 CONNECT 2 SETUP
DMX ADDRESS
DMX MODE
001-512 UNO
COLOR TEMPERATURE
WIRELESS
DUO BASIC
STANDARD EXTENDED WDMX ON/OFF WDMX mode
MANUAL COLOR
On-Off
SCREEN
TX link TX unlink
Transmitter Receiver On-Off
RX reset
On-Off
DMX to WDMX (TX) WDMX to DMX (RX)
On-Off On-Off
BACKLIGHT
FLIP DISPLAY KEY LOCK
ON 10 s 20 s 30 s ON OFF ON OFF
TEMPERATURE °C
UNIT
°F
TRANSFER
WITHOUT
CONFIGURA- DMX
TION
ADDRESS
WITH DMX
ADDRESS
Choose DMX Address
2700K 2800K 3000K 3200K 3500K 4000K 4500K 5000K 5600K 6000K 6500K WARM WHITE COLD WHITE
0-255 0-255
Choose DMX Mode
Enable/Disable the wireless card.
Allows to choose whether to set the wireless on the Transmitter or Receiver.
WDMX mode is unlocked only if WDMX ON / OFF is ON. TX link unlock when the
unit is set as a transmitter..
Disconnect the transmitter from all receivers. TX unlink unlocks only if WDMX
mode is on transmitter. Total reset of the receiver. RX reset unlocks only if
WDMX mode is receiver. Enable/Disable the transmission of the dmx from the
transmitter to the receiver via wdmx. Enable/Disable the retransmission of the
DMX from the receiver to the other units connected by cable to the receiver
itself. Allows you to select the timing after that display will switch
automatically off when unactive.
Allows you to rotate the display by 180°.
Allows you lock the buttons on the control panel by a password. Press
following combinations (password) in order to access to the user menu : UP,
DOWN, UP, DOWN, ENTER, To choose the desired unit of temperature measurement.
To transfer the same menu settings of one fixtures to all the other in the
daisy chain, including or not the dmx address.
PROLIGHTS – EclExpo Flood150VW
13
3 ADVANCED
DIMMER CURVE
DIMMER SPEED WHITE CALIBRATION LED FREQUENCY
DMX FAULT
FAN MODE
OUTPUT CONTROL
LINEAR S-CURVE SQUARE LAW INVERSE SQUARE LAW AUTO FAST MEDIUM SLOW OFF MANUAL
600Hz 1200Hz 2000Hz 4000Hz 6000Hz 25KHz BLACKOUT HOLD STAND ALONE AUTO HIGH
SILENT OFF CONSTANT
CW WW
To choose the dimmer curve. To choose the dimmer speed.
Select PWM frequency.
To choose the behaviour of fixture in case of dmx signal lost. Select the
product Fan mode. Ouput power will be reduced instantly in order to keep
output constant.
DYNAMIC
Ouput power will be reduced in time according to fixture temperature.
FACTORY RELOAD
4 INFORMATION INFORMATIONS
ON OFF DEVICE TIME
To reset the unit to factory default settings.
FIXTURE HOURS
CURRENT HOURS SOURCE HOURS
TOTAL PARTIAL TOTAL PARTIAL TOTAL PARTIAL
To check the total working hours of the unit. To check the current working hours of the unit. To see the total operating hours of the LED source.
POWER CONSUMPTION TEMPERATURE
FAN SPEED
POWER ON CYCLE MAINTENANCE TIME
NEAR SOURCE TEMP, DRIVER PCB TEMP, LED PCB TEMP,…
TOTAL PARTIAL ELAPSED TIME ALERT PERIOD
To see the power cycles of the machine. To choose and reset unit maintenance
warning hours. To see the power consumption. To see the unit temperature.
To see the speed of the fans.
CHANNEL VALUE
ERROR MESSAGE FIXTURE MODEL DEVICE LABEL
To see the dmx value of those channels. To see any error messages. View informations about fixture model. To see device label.
SOFTWARE VERSION
View informations about software version.
RDM UID
View ID for the RDM control.
14
PROLIGHTS – EclExpo Flood150VW
5 STAND ALONE MASTER/ SLAVE
EFFECTS
CCT WW+CW STATIC
MASTER DMX MASTER NO DMX SLAVE EFFECT 1 EFFECT 2 EFFECT 3 EFFECT 4
FIXED COLOR WW CW WW+CW
COLOR
2700K
TEMPERATURE
2800K
3000K
3200K
3500K
4000K
4500K
5000K
5600K
6000K
MANUAL COLOR
6500K WW CW STROBE
Allow you to link and operating in synk multiple units without a DMX console. Choose a unit to perform as the Master. This unit must be the first unit in line; Set the successive units to be slave. Use the rotary knob to select the Effect: KNOB 1 make effect, KNOB 2 make speed.
Use the rotary knob 2 to set the CCT value:KNOB 1 make dimmer, KNOB 2 make linear CCT. Use the rotary knob 1 and 2 to set the WW and CW value.
DIMMER <000 – 255>
STROBE <000 – 255> DIMMER <000 – 255>
Select of the following predefined color combination and its Dimmer value. After enabled this mode, the unit will be automatically assigned as Master Select a predefined White preset.
<000 – 255> <000 – 255> <000 – 255>
User generated color preset by assigning values to each primary color attribute. After enabled this mode, the unit will be automatically assigned as Master
PROLIGHTS – EclExpo Flood150VW
15
10 – RDM FUNCTIONS
The product can communicate using RDM (Remote Device Management) protocol over
a DMX512 Networks. RDM is a bi-directional communications protocol for use in
DMX512 control systems, it is the open standard for DMX512 device
configuration and status monitoring. The RDM protocol allows data packets to
be inserted into a DMX512 data stream without affecting existing non-RDM
equipment. It allows a console or dedicated RDM controller to send commands to
and receive messages from specific fixtures. The PIDs in the following tables
are supported in the product. RDM Model ID: 0xD128
Parameter
Category
PID Address
GET
SET
DEVICE_INFO
Product Information
0x0060
x
PRODUCT_DETAILID LIST
Product Information
0x0070
x
DEVICE_MODEL_DESCRIPTION
Product Information
0x0080
x
MANUFACTURER_LABEL
Product Information
0x0081
x
DEVICE_LABEL
Product Information
0x0082
x
x
FACTORY_DEFAULTS
Product Information
0x0090
x
x
SOFTWAREVERSION LABEL
Product Information
0x00C0
x
DMX_PERSONALITY
DMX512 Setup
0x00E0
x
x
DMX_PERSONALITY_DESCRIPTION
DMX512 Setup
0x00E1
x
DMX_START_ADDRESS
DMX512 Setup
0x00F0
x
x
DIMMER_INFO
Dimmer Settings
0x0340
x
CURVE
Dimmer Settings
0x0343
x
x
CURVE_DESCRIPTION
Dimmer Settings
0x0344
x
x
OUTPUT_RESPONSE_TIME
Dimmer Settings
0x0345
x
x
OUTPUTRESPONSE TIME_ DESCRIPTION
Dimmer Settings
0x0346
x
MODULATION_FREQUENCY
Dimmer Settings
0x0347
x
x
MODULATIONFREQUENCY DESCRIPTION
Dimmer Settings
0x0348
x
SENSOR_DEFINITION Sensors 0x0200 x
Value
Description
16
PROLIGHTS – EclExpo Flood150VW
Default Value
Parameter SENSOR_VALUE
Category
PID Address
GET
SET
Sensors 0x0201 x x
DEVICE_HOURS
Power/ Lamp Set- 0x0400 x x
tings
LAMP_HOURS
Power/ Lamp Set- 0x0401 x x
tings
LAMP_STRIKES
Power/ Lamp Set- 0x0402 x x
tings
LAMP_STATE
Power/ Lamp Set- 0x0403 x x
tings
LAMP_ON_MODE
Power/ Lamp Set- 0x0404 x x
tings
Power/ DEVICE_POWER_CYCLES Lamp Set- 0x0405 x x
tings
DISPLAY_INVERT
IDENTIFY_DEVICE IDENTIFY_MODE
Display Settings
0x0500
x
x
Control 0x1000 x x
Control 0x1040 x x
DMX FAULT
Manufacturer PIDs
0x82DD
x
x
MASTER/SLAVE
Manufacturer PIDs
0x8211
x
x
STAND ALONE MODE
Manufacturer PIDs
0x82EC
x
x
FX SELECTOR FX SPEED
FIXED COLOR
Manufacturer PIDs
0x8209
x
x
Manufacturer PIDs
0x8210
x
x
Manufacturer PIDs
0x82BE
x
x
COLOR TEMPERATURE
Manufacturer PIDs
0x82BF
x
x
MANUAL WW MANUAL CW
FAN
Manufacturer PIDs
0x82E2
x
x
Manufacturer PIDs
0x82E3
x
x
Manufacturer PIDs
0x82D2
x
x
Value
0-2 0-2 0-3 0-3 0-99 0-2 0-9 0 – 255 0 – 255 0 – 3
Description
0: Blackout 1: Hold 2: Standalone Mode 0: Master DMX 1: Master No DMX 2: Slave
0: Static 1: CCT preset 2: Manual WW/CW 3: FX (Effect) Choose Effect 0-3 Set
speed of FXs 0: Full WW 1: Full CW 2: Full WW+CW 0: 2700K 1: 2800K 2: 3200K 3:
3500K 4: 4000K 5: 4500K 6: 5000K 7: 5600K 8: 6000K 9: 6500K Set level of WW in
Manual WW/CW mode Set level of CW in Manual WW/CW mode 0: Auto 1: High 2:
Silent 3: Off
Default Value
0 0 1 0 99 1 4 255 255 0
PROLIGHTS – EclExpo Flood150VW
17
Parameter
OUTPUT CONTROL
WHITE CALIBRATIN WW
WHITE CALIBRATIN CW
CURRENT HOURS
POWER CONSUMPTION MAINTENANCE TIME:A-
LERT PERIOD MAINTENANCE TIME:E-
LAPSED TIME ERROR MESSAGE
CLEAN ALL DATA
Category
PID Address
GET
SET
Value
Description
Default Value
Manufacturer PIDs
0x830C
x
x
0 – 1
0: Dynamic 1: Constant
0
Manufacturer PIDs
0x82C6
x
x
125 255
Calibrate level of WW
—
Manufacturer PIDs
0x82C7
x
x
125 255
Calibrate level of CW
—
Manufacturer PIDs
0x82C5
x
0 65535
Show Fixture Hours
—
Manufacturer PIDs
0x82DE
x
Show Power Consumption (W)
—
Manufacturer PIDs
0x82DF
x
10-300
300
Manufacturer PIDs
0x82E0
x
x
0-ALERT PERIOD
—
Manufacturer PIDs
0x82E0
x
—
Manufacturer PIDs
0x82C8
x
x
0 – 1
0: No 1: Yes
0
11 – SHORTCUTS
Keys MENU + ENTER then power on
UP + DOWN after power on MENU + ENTER while on Home Screen
Mode
Description
Clear All
Flip Display Home Screen /
StandAlone
Clear all value of functions + factory defaul Directly flip display without
enter inside menu
Lock on / Lock off
12 – ERRORS
ERRROR SHOWED [LED TEMPERATURE SENSOR ERROR] [TEMPERATURE TOO HIGH] [MAINTENANCE TIME] [DMX ACTIVE]
POSSIBLE CAUSES
LED temperture sensor damaged (open or in short circuit) This error message
indicates that an overheating has occurred and the led has been
switched OFF by the product protection system. Need to be done standard
maintenance and also reset of elapsed time
Transfer configuration is used with dmx signal connected
18
PROLIGHTS – EclExpo Flood150VW
13 – DMX CHARTS
RDM Model ID: 0xD128
RDM Personality ID List
ID
DMX Mode
1
UNO
2
DUO
3
BASIC
4
STANDARD
5
EXTENDED
Channel 1 2 3 4 5 6 7 8 9 10 11
UNO DIMMER
DUO DIMMER
CCT
BASIC DIMMER WARM WHITE COLD WHITE
STANDARD DIMMER
DIMMER FINE STROBE
EXTENDED DIMMER
DIMMER FINE STROBE
CCT
CCT
CCT FINE
CCT FINE
CROSSFADE WARM WHITE WARM WHITE FINE
COLD WHITE
COLD WHITE FINE FUNCTION
PROLIGHTS – EclExpo Flood150VW
19
UNO 1
DUO 1
2
BASIC STANDARD EXTENDED
Function
1
1
2
3
4
5 2 3
1
DIMMER 0~100%
2
DIMMER FINE
STROBE
Close
Strobe from slow to fast
Open
3
Pulse in from slow to fast Open
Pulse out from slow to fast
Open
Randon from slow to fast
Open
CCT
2700K – 2800K
2800K – 2900K
2900K – 3000K
3000K – 3100K
3100K – 3200K
3200K – 3300K
3300K – 3400K
3400K – 3500K
3500K – 3600K
3600K – 3700K
3700K – 3800K
3800K – 3900K
3900K – 4000K
4000K – 4100K
4100K – 4200K
4200K – 4300K
4300K – 4400K
4400K – 4500K
4
4500K – 4600K
4600K – 4700K
4700K – 4800K
4800K – 4900K
4900K – 5000K
5000K – 5100K
5100K – 5200K
5200K – 5300K
5300K – 5400K
5400K – 5500K
5500K – 5600K
5600K – 5700K
5700K – 5800K
5800K – 5900K
5900K – 6000K
6000K – 6100K
6100K – 6200K
6200K – 6300K
6300K – 6400K
6400K – 6500K
5
CCT FINE
6
CROSSFADE CCT to WW/CW 0~100%
7
WARM WHITE 0~100%
8
WARM WHITE FINE
9
COLD WHITE 0~100%
DMX Value Default
000 ÷ 255
000
000 ÷ 255
000
000 ÷ 001
002 ÷ 062
063 ÷ 064
065 ÷ 125 126 ÷ 127
255
128 ÷ 188
189 ÷ 190
191 ÷ 251
252 ÷ 255
0 ÷ 7
7 ÷ 13
13 ÷ 20
20 ÷ 27
27 ÷ 34
34 ÷ 40
40 ÷ 47
47 ÷ 54
54 ÷ 60
60 ÷ 67
67 ÷ 74 74 ÷ 81
81 ÷ 87
87 ÷ 94
94 ÷ 101
101 ÷ 107
107 ÷ 114
114 ÷ 121
121 ÷ 128
000
128 ÷ 134
134 ÷ 141 141 ÷ 148
148 ÷ 154
154 ÷ 161 161 ÷ 168
168 ÷ 174
174 ÷ 181
181 ÷ 188
188 ÷ 195
195 ÷ 201 201 ÷ 208
208 ÷ 215
215 ÷ 221 221 ÷ 228
228 ÷ 235
235 ÷ 242 242 ÷ 248
248 ÷ 255
000 ÷ 255
000
000 ÷ 255
000
000 ÷ 255
255
000 ÷ 255
255
000 ÷ 255
255
20
PROLIGHTS – EclExpo Flood150VW
UNO
DUO
BASIC STANDARD EXTENDED
Function
DMX Value
10
COLD WHITE FINE
000 ÷ 255
FUNCTION
No Function Display Backlight On Display Backlight 10 s Display Backlight 20 s Display Backlight 30 s
000 ÷ 001 002 ÷ 003 004 ÷ 005 006 ÷ 007 008 ÷ 009
Display Flip Regular
010 ÷ 011
Display Flip Top Down
012 ÷ 013
Display Key Lock ON
014 ÷ 015
Display Key Lock OFF
016 ÷ 017
Dimmer Mode Linear
018 ÷ 019
Dimmer Mode S-Curve
020 ÷ 021
Dimmer Mode Square Law
022 ÷ 023
Dimmer Mode Inverse Square Law 024 ÷ 025
Dimmer Speed Auto Dimmer Speed Slow Dimmer Speed Medium
026 ÷ 027 028 ÷ 029 030 ÷ 031
Dimmer Speed Fast
032 ÷ 033
White Calibration OFF
White Calibration MANUAL
LED Frequency 600 Hz
LED Frequency 1200 Hz
LED Frequency 2000 Hz
LED Frequency 4000 Hz
11
LED Frequency 6000 Hz
LED Frequency 25 kHz
DMX Lost Blackout
DMX Lost Hold
DMX Lost Stand Alone
034 ÷ 035 036 ÷ 037 038 ÷ 039 040 ÷ 041 042 ÷ 043 044 ÷ 045 046 ÷ 047 048 ÷ 049 050 ÷ 051 052 ÷ 053 054 ÷ 055
Fan Auto Fan Silent
056 ÷ 057 058 ÷ 059
Fan High
060 ÷ 061
Fan OFF Stand Alone Master Dmx Stand Alone Master No Dmx Stand Alone Slave
062 ÷ 063 064 ÷ 065 066 ÷ 067 068 ÷ 069
Stand Alone Effect
070 ÷ 071
Stand Alone CCT
072 ÷ 073
Stand Alone WW+CW
074 ÷ 075
Stand Alone White Presets Stand Alone Fixed Color Stand Alone Color Temperature Stand Alone Manual Color Menu Stand Alone Output Control Constant Output Control Dynamic RESERVED FACTORY DEFAULT OF ALL CONTROLLED FUNCTION
076 ÷ 077 078 ÷ 079 080 ÷ 081 082 ÷ 083 084 ÷ 085 086 ÷ 087 088 ÷ 089 090 ÷ 253 254 ÷ 255
Default 255
000
PROLIGHTS – EclExpo Flood150VW
21
14 – ACCESSORIES INSTALLATION
FILTER FRAME (CODE ECLEXPOFL150FFBK – OPTIONAL)
DETAIL 1
DETAIL 2
Anti-Glare Louvre Filter Frame
DETAIL 3
Insert the anti-glare louvre into the slot (DETAIL 1). Pull the knob out
(DETAIL 2) and insert the accessory filter frame from the top into the guide
on the hardware of the unit (DETAIL 3). Then release the knob (DETAIL 3).
NOTE: To remove the accessory, reverse the procedure.
Fig. 08
22
PROLIGHTS – EclExpo Flood150VW
BARNDOOR (CODE ECLEXPOFL150BDBK – OPTIONAL)
DETAIL 1
DETAIL 2
Unscrew the knob of the barndoor accessory (DETAIL 1). Then mount the barndoor
by screwing the knob with the hole on the unit hardware (DETAIL 2). NOTE: To
remove the accessory, reverse the procedure.
Fig. 09
PROLIGHTS – EclExpo Flood150VW
23
CRMX WIRELESS KIT (CODE ECLEXPOFL150WKBK – OPTIONAL)
To install the wireless kit, you need to open the apperecchio and follow the following instructions:
1
2
Unscrew the screws as shown in Figures 1 and 2 and remove the top cover. 3
Unscrew the screw and remove the antenna cover.
24
PROLIGHTS – EclExpo Flood150VW
Fig. 10
4
5
Secure the antenna in the space provided and screw in the 2 screws in Figure 5. 6
Finally, attach the TIMO board using the appropriate connector, and reassemble
the cover by screwing all the screws back in.
NOTE: To remove the accessory, reverse the procedure.
PROLIGHTS – EclExpo Flood150VW
Fig. 11
25
15 – MAINTENANCE
MAINTENANCE AND CLEANING THE PRODUCT WARNING: Disconnect from the mains before
starting any maintenance work It is recommended to clean the front at regular
intervals, from impurities caused by dust, smoke, or other particles to ensure
that the light is radiated at maximum brightness. · For cleaning, disconnect
the main plug from the socket. Use a soft, clean cloth moistened with a
mild detergent. Then carefully wipe the part dry. For cleaning other housing
parts use only a soft, clean cloth. Never use a liquid, it might penetrate the
unit and cause damage to it. · The user must clean the product periodically to
maintain optimum performance and cooling. The user may also upload firmware
(product software) to the fixture via the DMX signal input port or USB port
using firmware and instructions from PROLIGHTS. · The frequency of such
maintenance operations is to be performed according to various factors, such
as the amount of the use and the condition of the installation environment
(air humidity, presence of dust, salinity, etc.). It is recommended that the
product is subject to annual service by a qualified technician for special
maintenance involving at least the following procedures: · General cleaning of
internal parts. · Restoring lubrication of all parts subject to friction,
using lubricants specifically supplied by PROLIGHTS. · General visual check of
the internal components, cabling, mechanical parts, etc. · Electrical,
photometric and functional checks; eventual repairs. · Cleaning the lenses.
Only use neutral soap and water to clean the lenses, then dry it carefully
with a soft, non-abrasive cloth. WARNING: the use of alcohol or any other
detergent could damage the lenses. · All other service operations on the
product must be carried out by PROLIGHTS, its approved service agents or
trained and qualified personnel. · It is PROLIGHTS policy to apply the
strictest possible calibration procedures and use the best quality materials
available to ensure optimum performance and the longest possible component
lifetimes. However, optical components are subject to wear and tear over the
life of the product, resulting in gradual changes in colours over many
thousands of hours of use. The extent of wear and tear depends heavily on
operating conditions and environment, so it is impossible to specify precisely
whether and to what extent performance will be affected. However, you may
eventually need to replace optical components if their characteristics are
affected by wear and tear after an extended period of use and if you require
fixtures to perform within very precise optical and colour parameters. · Do
not apply filters, lenses or other materials on lenses or other optical
components. Use only accessories approved by PROLIGHTS.
REPLACING THE FUSE WARNING: Before replacing the fuse, unplug the product from
the mains.
· Remove the old fuse from the housing with a suitable screwdriver
(anticlockwise) and replace it with one of the same type and of the same
classification (T5A 250V).
VISUAL CHECK OF PRODUCT HOUSING
· The parts of the product cover/housing should be checked for eventual
damages and breaking start at least every two months. In addition, especially
the parts of the front lens holder have to be checked mechanically (by means
of movement by the part) if it is firmly fastened to the fixture. If hint of a
crack is found on some plastic part, do not use the product until the damaged
part will be replaced.
· Cracks or another damages of the cover/housing parts can be caused by the
product transportation or manipulation and also ageing process may influence
materials.
· This checking is necessary for both fixed installations and preparing
product for renting. Any free moving parts inside of the product, cracked
cover/housing or any part of front lens not sitting properly in place need to
be immediately replaced.
26
PROLIGHTS – EclExpo Flood150VW
TROUBLESHOOTING
Problems
Possible causes
Checks and remedies
Product doesn’t power ON · No power to the product. · Check that power is switched ON and cables are plugged in.
Product reset correctly but does not respond correctly to the contoller.
· Fuse blown or internal · Check if the Fuse is intact and eventually replace it if
fault.
necessary. · Contact the PROLIGHTS Service or authorized service
partner. Do not remove parts and/or covers, or carry
out any repairs or service that are not described in this Safety and User Manual unless you have both
authorization from PROLIGHTS and the service
documentation.
· Bad signal connection. · Inspect connections and cables. Fix eventual bad connections. Repair or replace damaged cables.
· Signal connection not · Insert DMX termination plug in signal output socket of
terminated.
the last product on the signal line.
Timeout error after fixture reset.
Mechanical effect loses position
· Incorrect addressing of · Check the product address and control settings. the product.
· One of the product is · Unplug the XLR in and out connectors and connect
defective and is corrupt- them directly together to bypass one product at a
ing the signal transmis- time until normal operation is regained. Once found
sion on the signal line.
the error, have that fixture serviced by a qualified
technician.
· One or more hardware · Check product stored error messages for more components requires information. Contact PROLIGHTS Service or an mechanical adjustments. authorized service partner.
· Mechanical hardware · Check product stored error messages for more
require cleaning, adjust- information. Contact PROLIGHTS Service or an
ment or lubrification.
authorized service partner.
Light output turn OFF Intermittently
General low light intensity
· Fixture is too hot.
· Check product stored error messages. · Allow product to cool. · Clean the product and airflow filters. · Reduce ambient temperature.
· Hardware failure (tem- · Check product stored error messages for more
perature sensor, fans, Light source…).
information. Contact PROLIGHTS Service or an authorized service partner.
· Dirty lens assembly
· Clean the fixture regularly.
· Dirty or damaged filters · Install lens assembly properly.
Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.
PROLIGHTS – EclExpo Flood150VW
27
Note
PROLIGHTS is a trademark of MUSIC & LIGHTS S.r.l. musiclights.it
Via A.Olivetti snc 04026 – Minturno (LT) ITALY Tel: +39 0771 72190
prolights.it support@prolights.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>