PROLiGHTS Portable Battery-Powered Uplighter User Manual

June 12, 2024
PROLIGHTS

PROLiGHTS Portable Battery-Powered Uplighter User Manual
PROLiGHTS Portable Battery-Powered Uplighter

WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with cure for future reference. It contains important information about the installation, usage and maintenance of the unit.

SAFETY

General instruction

  • The products referred to in this manual conform to the European Community Directives and are therefore marked with .
  • Supply voltage of this product is DC24V; never connect directly to AC220V. Leave servicing to skilled personnel only. Never make any modifications on the unit not described in this instruction manual, otherwise you will risk an electric shock.
  • Connection of the power adapter must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
  • The connection to the main network of electric distribution must be carried out by a qualified electrical installer. Check that the voltage correspond to those for which the unit is designed as given on the  electrical data label.
  • This unit is not for home use, only professional applications.
  • Never use the fixture under the following conditions:
    • in places subject to vibrations or bumps;
    • in places subject to excessive humidity.
  • Make certain that no inflammable liquids, water or metal objects enter the fixture.
  • Do not dismantle or modify the fixture.
  • All work must always be carried out by qualified technical personnel. Contact the nearest sales point foran inspection or contact the manufacturer directly.
  • If the unit is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
  • If this device will be operated in any way different to the one described in this manual, it may suffer damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers likeshort circuit, burns, electric shock, etc.
  • Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
  • Always additionally secure the projector with the safety rope. When carrying out any work, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.
  • Install the fixture in a well ventilated place.
  • Keep any inflammable material at a safe distance from the fixture.
  • Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired.
  • The lamp (LED) shall be changed if it has become damaged or thermally deformed.
  • Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
  • Do not touch the product’s housing when operating because it may be very hot.

INTRODUCTION

TECHNICAL DRAWING
Dimensions

OPERATING ELEMENTS AND CONNECTIONS

Parts

  1. CONTROL PANEL with display and 4 button used to access the control panel functions and manage them.
  2. Adjustable foot support for tilt regulation (up to 20°).
  3. ON/OFF SWITCH.
  4. CHARGING CONTACT
  5. RELEASE LEVER to adjustable foot support
  6. CARRYING HANDLE
  7. IR SENSOR
  8. Wireless DMX RECEIVER

INSTALLATION

MOUNTING
SMARTBATPLUS may be set up on a solid and even surface. The unit can also be mounted upside down to a cross arm. For fixing, stable mounting clips are required. The mounting place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installation, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country in which the fixture’s being used.

IMPORTANT
Always additionally secure the projector with the safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.
Installation

FUNCTIONS AND SETTINGS

OPERATION
Switch on the SMARTBATPLUS with the power switch. The unit is ready for operation and can be operated via a DMX controller or it independently performs its show program in succession. After operation, switch off the unit with the power switch.

BASIC SETUP
The SMARTBATPLUS has a OLED display and 4 buttons for access to the functions of the control panel ( fig. 5 )

Setup

MENU
Used to access the menu or to return a previous menu option| UP
Button to select the values in ascending order of the function| DOWN
Button to select the values in descending order of the function| ENTER
Used to select and store the current menu or confirm the current function value or option within a menu

RECHARGE

To recharge SMARTBAT:

  • connect the unit to the special battery charger through the lower connector
  • connect the battery charger to the power supply

NOTE – The charging time are 4 h and autonomy is 12h

Flight-case SMARTBATPLUSPACK (optional)

Flight-case designed to contain 6pcs SMARTBATPLUS with battery charger kit included..

  • Internal separated compartments with charger plug for every device
  • Case power input: Powercon IN
  • Dimensions (LxHxD): 537x540x470 mm

NOTE: Always charge with flight-case open.
Charging Instruction

Menu Structure

AUTO SHOW

This fixture has a built-in automatic program. To access this, please see the below instructions:

  • Press the MENU button so many times until shows [Autoshow].
  • Press the ENTER button to confirm.
  • Using UP/DOWN button, select one of the programs [Auto 1 – Auto 5].
  • Press the ENTER button save the setting.
  • Using UP/DOWN button, select the speed value of the show [S1 – S100].
  • Press the ENTER button save the setting.

STATIC COLOR

This fixture has the ability to accept custom static color settings. Access these chases via the control panel on the back of the fixture.

  • Press the MENU button so many times until shows [Static ].
  • Press the ENTER button to confirm.
  • Press the MENU button so many times until shows [Fixed Color].
  • Press the ENTER button to confirm.
  • Using UP/DOWN button, select one of the programs [R,G,B,W,…..,RGB,….,RGBW].
  • Press the ENTER button save the setting.

MANUAL COLOR
To set the personal balance of the color refer to the following procedure:

  • Press the MENU button so many times until the display shows [Static]
  • Press the ENTER button to confirm.
  • Press the MENU button so many times until shows [Manual Color].
  • Press the ENTER button to confirm.
  • Using UP/DOWN button, select one of the programs [R,G,B,W].
  • Press the ENTER button to confirm.
  • Using UP/DOWN button, select the wanted value of the program [000-255].
  • Press the ENTER button save the setting and to pass to the successive color.
  • Continue until obtain the wanted color mix.

IR SETUP
To start up the IR recevitor refer to the following steps:

  • Press the MENU button so many times until the display shows [IR Setup].
  • Press the ENTER button to confirm.
  • Press the UP/DOWN button, select one of the programs [ON] or [OFF].
  • Press the ENTER button for save the setting.
  • To use the remote control it is necessary to set the fixture in Static or Auto Mode.

NOTE:  Make sure to point the controller directly at the receiver on the product.

WIRELESS SETTING

  • To set the wireless mode refer to the following guide:
  • Press the MODE button until the display shows Wireless Setting, then press the ENTER button.
  • Use the UP/DOWN button until the display reads Wireless Receive, and then press the ENTER button and select the ON mode.
  • Press the MODE button to go back or to meet the waiting time to exit the setup menu. NOTE – After you complete these steps, you have to synchronize with any wifi unit with which you want to communicate by pressing the sync button present on the same. Then connect any DMX console to wifi
  • unit for to open the communication with the SMARTBATPLUS unit.
  • To reset the unit press the MODE button until the display shows Wireless Reset, then press the ENTERbutton.
  • Use the UP/DOWN button until the display reads Yes, and then press the ENTER button.
  • Press the MODE button to go back or to meet the waiting time to exit the setup menu.

DIMMER MODE

  • Enter in Dimmer mode to select specific dimming curve, press the MENU button so many times until shows [DIMMER MODE], and press the ENTER button to confirm.
  • Press the button UP/DOWN to select [Off – Dimer 1 – Dimmer 2 – Dimmer 3].
  • Press ENTER button to store.
  • Press the MENU button to go back or to meet the waiting time to exit the setup menu.

DMX MODE

  • Press the MENU button so many times until shows, [DMX Channel] and press the ENTER button to confirm.
  • Press the UP/DOWN button to select the desired DMX mode [4Ch], [6Ch], [10Ch], [HSV], [HSI] and press the ENTER button to for save the setting.
  • The tables on page 14 indicate the operating mode and DMX value.

DMX ADDRESSING

To be able to operate the SMARTBATPLUS with a light controller, set the unit DMX start address for the firstDMX channel. To set the start address refer to following procedure:

  • Use the UP/DOWN button until the display reads [DMX Address] and then press the ENTER button to confirm
  • Press the UP/DOWN button to select the value [d 1-509] and then press the ENTER button .

If e. g. address 33 on the controller is provided for controlling the function of the first DMX channel, adjust the start address 33 on the SMARTBAT.

The other functions of the light effect panel are then automatically assigned to the following addresses. An example with the start address 33 is shown in the page 13.

KEY LOCK

Enter the Key Lock mode to select whether the access password is on or off.

  • Press the button MODE so many times until show Key Lock and press the button ENTER to confirm.
  • Use UP/DOWN button to select: ON or OFF.
  • Press ENTER button to confirm the selection. When the fixture is set as pass ON, after 30 seconds or turn on the fixture next time, the fixture will need an access password to enter the display menu control.
    NOTE – The factory access password is UP + DOWN + UP + DOWN (press ENTER to confirm the access)

DMX Channels number| Start address (example)| Busy DMX address| Next possible start address for unit n°1| Next possible start address for unit n°2| Next possible start address for unit n°3
---|---|---|---|---|---
4| 33| 33-36| 37| 41| 45

Channel Configuration

DMX CHANNELS

MODE 10 Ch FUNCTION DMX Value
1 DIMMER 0~100% **** 000 – 255
2 RED 0~100% **** 000 – 255
3 GREEN 0~100% **** 000 – 255
4 BLUE 0~100% **** 000 – 255
5 WHITE 0~100% **** 000 – 255
**** 6 STROBE No Function Strobe slow to fast **** 000 – 010011 – 255
7 COLOR PRESET + WHITE BALANCE No FunctionR 100% G 0~100% B 0R 100%~0 G

100% B 0R 0 G 100% B 0~100%R 0 G 100%~0 B 100%R 0~100% G 0 B 100%R 100% G 0 B 100%~0R 100% G 0~100% B 0~100% R 100%~0 G 100%~0 B 100%R 100% G 100% B 100% W 100%White Balance 1White Balance 2White Balance 3White Balance 4White Balance 5White Balance 6White Balance 7White Balance 8White Balance 9White Balance 10White Balance 11| 000-010011-030031-050051-070071-090091-110111-130131-150151-170171-200201-205206-210211-215216-220221-225226-230231-235236-240241-245246-250251-255
8| AUTO/SOUND PROGRAMS No Function Auto Program 1Auto Program 2Auto Program 3Auto Program 4| ** 000-051052-101102-152153-203204-254
MODE 10 Ch| FUNCTION| DMX Value
---|---|---
8| Auto Program 5| 255
9|
AUTO SPEED Speed slow to fast| ** 000 – 255
10| DIMMER CURVE Preset dimmer speed from display menu Dimmer speed mode offDimmer speed mode1 (fast speed) Dimmer speed mode2 (middle speed)Dimmer speed mode3 (slow speed)| ** 000-051052-101102-152153-203204-255
MODE 4 Ch| FUNCTION| DMX Value
---|---|---
1|
RED 0~100%| ** 000 – 255
2| GREEN 0~100%| ** 000 – 255
3|
BLUE 0~100%| ** 000 – 255
4| WHITE 0~100%| **** 000 – 255

MODE 6 Ch FUNCTION DMX Value
1 MASTER DIMMER 0~100% **** 000 – 255
2 RED 0~100% **** 000 – 255
3 GREEN 0~100% **** 000 – 255
4 BLUE 0~100% **** 000 – 255
5 WHITE 0~100% **** 000 – 255
**** 6 STROBE No Function Strobe slow to fast **** 000 – 010011 – 255

MAINTENANCE

MAINTENANCE AND CLEANING THE UNIT

  • Make sure the area below the installation place is free from unwanted persons during setup.
  • Switch off the unit, unplug the main cable and wait until the unit has cooled down.
  • All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded.
  • Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totally free from any deformation.
  • The main cables must be in impeccable condition and should be replaced immediately even when a small problem is detected.
  • It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.

Battery Guide

New Lithium Battery Initialisation
Any new fixture containing a Lithium battery should be initialised when first purchased to maximise its battery life. To do this:

  1. Fully charge the unit for a minimum of 5 to 6 hours.
  2. Fully discharge, then fully recharge the battery.
  3. Repeat this cycle another 2 times for optimum battery life

Maximizing Battery Performance

  1. Lithium batteries perform best when in regular use. Long idle periods will reduce the battery life.
  2. Recharge the battery at the earliest opportunity, leaving batteries discharged for long periods will reduce battery life.
  3. Store units containing Lithium batteries at cool temperatures. High ambient temperatures significantly reduce the life of a Lithium battery.
  4. Disconnect power from the unit when charging is complete.
  5. Do not use fixtures whilst charging.

Long term storage

  1. Charge your fixture’s battery to around 50%. If you store a fixture with a fully discharged battery, it could fall into a deep discharge state. If you store it fully charged, the battery may lose some capacity, leading to shorter battery life.
  2. Power down the device to avoid additional battery use.
  3. Place your device in a cool, moisture-free environment that’s less than 32° C (90° F).

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PROLIGHTS User Manuals

Related Manuals