Autige W19 3 In 1 Wireless Charging Station User Manual

September 7, 2024
AUTIGE

Autige W19 3 In 1 Wireless Charging Station

Product Information

Specifications:

  • Model: XYZ-500
  • Power: 1200W
  • Capacity: 5 liters
  • Material: Stainless steel
  • Weight: 3.5 kg

Product Usage Instructions

Initial Setup:
Before using the product for the first time, make sure to wash all removable parts with warm soapy water and dry thoroughly.

Filling the Reservoir:
Open the lid of the product and fill the reservoir with water up to the maximum fill line indicated.

Operating the Product:
Plug in the product and set the desired temperature using the control panel. The product will start heating up the water.

Dispensing Hot Water:
Once the water reaches the set temperature, use the dispensing lever to pour hot water into your container.

Cleaning and Maintenance:
After each use, unplug the product and allow it to cool down. Clean the exterior with a damp cloth and descale the interior regularly to prevent mineral buildup.

FAQs (Frequently Asked Questions)

  • Q: Can I use this product to boil liquids other than water?
    A: No, this product is designed specifically for heating and dispensing water. Do not use it for any other liquids.

  • Q: How often should I descale the product?
    A: It is recommended to descale the product every 1-2 months, depending on your usage and water hardness.

  • Q: Is the product dishwasher safe?
    A: No, do not place any part of the product in the dishwasher. Hand wash only.

Device Layout

Rotating Mode

Horizontal / Vertical Mode

Magnetic Charging

Product Parameter

  • Product Name: Rotating 3 in 1 Wireless Charger Station
  • Product Size: 98.898.8105.5mm / 3.89×3.89×4.15 in
  • Product Color: Black/White
  • Product Material: ABS+Silicone
  • Input: 9V/2A 12V/2A
  • Mobile Phone Output: 15W/10W/7.5W/5W
  • Headphone Output: 3W max
  • iWatch Output: 2.5W
  • Compatibility: support mobile phones, Airpods, and iWatch that comply with the Qi standard

Steps for usage

  • The device is connected to the power supply through the charging cable, and then it can be powered on.
  • When charging the mobile phone, place the mobile phone in the mobile phone charging area to start charging, the magnetic wireless charging will automatically locate itself by magnetic force.
  • After fully charged, simply take off the phone;
  • When charging the Apple Watch, place the iWatch flat in the charging area to start charging the iWatch.
  • After fully charged, directly remove the iWatch;
  • When charging the Airpods, place the Airpods flat in the charging area to start charging;
  • After fully charged, simply remove the Airpods;

Special Note

  1. Recommended to use the supplied charging cable for the power supply, and not to use the original iPhone cable.
  2. Please use a qualified PD protocol or QC protocol power charger, otherwise may lead to unstable or abnormal blink
  3. If you use a protective shell, please use the mobile phone protection shell with the Magsafe function.
  4. Please do not use a mobile phone protection shell with a metal back or a mobile phone protection shell which thicker than 4mm.

LED light status indication

  • Power on: LED blue light flash
  • Standby: LED red light is on
  • Charging: LED blue light is on
  • Foreign body status: LED red and blue lights flash alternately

Packaging accessories

  • 3 in 1 wireless charger *1
  • Manual *1
  • USB-C charging cable *1

The content of this manual and product specifications are subject to change without notice.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals