PALADONE PP4845RM Dual Powered Light With Wall Mount Installation Guide

: September 7, 2024
: Paladone

Table of Contents

PALADONE PP4845RM Dual Powered Light With Wall Mount
Product Specifications
Product Usage Instructions
FAQ
Introduction
Wall mount instructions
FCC STATEMENT
FUNCTIONS
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PALADONE PP4845RM Dual Powered Light With Wall Mount

Product Specifications

USB-C Input: 5V DC 500mA
USB-C Port Output: 5V DC 500mA
Color: Black
Dimensions: 148mm (W) x 210mm (H)
Country of Origin: China

Product Usage Instructions

Installation

Warning: Changes or modifications not approved may void the user’s authority to operate the equipment. If interference occurs:

Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment to a different circuit than the receiver.
Consult dealer or technician for assistance.

FAQ

Q: What should I do if the device causes interference with radio or TV reception?
A: Try reorienting the antenna, increasing separation, connecting to a different outlet, or seeking assistance from a dealer or technician.
Q: How do I contact customer service for assistance?
A: You can contact customer service at the following numbers:

Introduction

Warning! Unsuitable for children under 3 years.

Misuse of the transformer can cause electrical shock.
The USB cable and power supply used with the toy are to be regularly examined for damage to the cord, plug, and other parts, and in the event of such damage, they must not be used until the damage has been repaired.
Under an environment with electrostatic discharge, the device may malfunction. If this happens, you will need to reset the device by turning it off/on again.
This product is not to be directly connected to the main supply.
This item can be used with a compatible mains-powered transformer.
This must be a short-circuit-proof safety isolating transformer according to IEC 61558-2-16 or a toy transformer according to IEC 61558-2-7.
The transformer is not a toy. Max-rated output: 5V DC.
The light can be powered by batteries or by USB-C.
When the USB-C cable is connected to the base the batteries will be bypassed.
LEDs are not replaceable. The crossed-out wheelie-bin symbol on this product is to remind you that waste electrical and electronic products, batteries, and accumulators should not be disposed of with household waste.
If you are unable to reuse or recycle your article it should be disposed of at a civic amenity site/local authority recycling facilities.
Use 3 x 1.5 V type AAA batteries. Take care to fit batteries observing the plus & minus markings.
Replace all used batteries at the same time.
Do not mix used and new batteries, rechargeable, different types (alkaline or carbon-zinc), or different brands of batteries.
Only use batteries of the same type. Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the product before being charged.
Rechargeable batteries are only to be charged under adult supervision.
The supply terminals are not to be short-circuited.
Exhausted batteries are to be removed immediately.
To insert/replace batteries: Unscrew the battery cover and insert batteries, observing the polarity guide.
Ensure the battery cover is securely screwed in place before use.
Packaging (and instructions if included) must be kept since they contain important information.

Wall mount instructions

CAUTION! Check that the wall/mounting surface is suitable for this type of installation before commencing.

Unfamiliarity with the tools and processes can be dangerous.
If you are uncomfortable or inexperienced working on these instructions, then consult a professional.
The following tools will be required for wall mounting: – Pencil – Tape Measure – Electric Drill – Spirit Level – 2 Wall Mounting Screws & 2 Fixings (please consult your local hardware store for advice on which type is required).
Select a suitable location for hanging. Ensure the power cable can reach the power supply.
Hold it against the wall and draw a faint outline with a pencil. On the back measure from the top & bottom edges to the center of the wall mount fixtures.
Transfer these measurements onto the wall and mark where the holes need to be drilled. Use a spirit level to check the holes are level.
Drill two holes using a suitable size and type of drill bit. Install the suitable wall fixings into the holes and screw in your mounting screws.
Mount onto the wall by matching the screws with the wall mount fixtures. Use the spirit level again to check the item is level.

The toy is only to be connected to equipment of Class II marked on the equipment with:

Pantone references/finishes

BLACK

Cutterguide Information

Indicates Cut

Cutterguide Information

148mm (W) x 210mm (H)

FCC STATEMENT

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.