En-Vision STS3 Scriptalk Station3 User Guide
- September 6, 2024
- En-Vision
Table of Contents
En-Vision STS3 Scriptalk Station3
Congratulations on your new
ScripTalk Station 3! This Quick Start Guide will help you get started on your
way to safety, privacy and independence in managing your prescription
medications.
What’s In the Box?
- ScripTalk Station 3 Reader Sample Bottle USB-A to USB-C Cable & USB-A Power Adapter
The Buttons
Three buttons allow you to operate the reader and access the information on your prescription labels.
About the Electronic Label
- The talking label may be found on the bottom or the side of your bottle or container.
- Due to packaging or medicine content, your label may be attached as an annex tag.
- To access the electronic label, lift it away from the package when scanning.
Battery Level
- The device will report the battery level during start-up when below 20% charge.
- To check the battery level at any time, unplug the device and turn it on.
- Let the device fully start up. Press all three buttons (PREV, READ and NEXT). Among other information spoken, the device will report the current charge level of the battery.
Recharging the Battery
Plug the charge adapter into a wall outlet, then plug the USB-C cable into the port on the left side of your Scrip Talk.
When charging is complete, your ScripTalk will let you know
“Battery Charging Completed.” Max charge should take no more than 5-6 hours
from a fully depleted level.
Power and Volume Control
Turn the thumbwheel switch clockwise to power on the unit.
To adjust the volume, turn the thumbwheel.
To shut off the unit, turn the thumbwheel counter-clockwise until you hear a
click.
On-Board Help
To listen to the instructions on how to use the unit, press and hold READ for
about three seconds. To stop the instructions, press READ again.
Press PREV or NEXT to move through the different topics.
Reading a Prescription Label
- To scan, press READ. You will hear beeping.
- Place your label on the top of the reader.
- Listen to the label information.
- To stop the speaking, press READ.
Scrolling Through the Information
While the unit is speaking the label information, you can press PREV or NEXT
to move through the information or to repeat an item.
Troubleshooting
Place your prescriptions on the reader individually. The unit can only read
one label at a time.
If the unit cannot find or read a label, it will give you a warning. Have a
sighted friend or a family member read the label for you, and talk to your
pharmacist to see about a new label.
Changing the Voice Speed
To change the voice speed, press and hold PREV or NEXT for three seconds, then press PREV or NEXT to find the speed you like. Press READ to set the speed.
Spell Mode
You can have the information spelled out if you don’t understand a word.
Select the slowest setting in voice speed.
It will say “Spell Mode.” Press READ to select, then scan your label.
Reset voice speed to exit.
Accessories
A handy travel bag is available for your convenience. The insulated zippered bag is designed to hold your reader as well as your medications. And it’s perfect for trips or organization of your medications.
Scrip Talk Travel Case $24.99
Headphones $15.99
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For more information or assistance, please contact us at:
- En-Vision America
- 825 4th St W
- Palmetto, FL 34221
- Toll Free: 800-890-1180
- Fax: 309-452-3643
frontdesk@envisionamerica.com www.envisionamerica.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>