DUSTBAN DB Series Commercial Dry Vacuum Instruction Manual

DUSTBAN DB Series Commercial Dry Vacuum

Parts & Operations Manual

• Serial Number
• Distributor Name
• Date of Purchase
• Date of Issue

SAFETY INFORMATION

Safety precautions
Read the “User Manual” carefully before start-up and use or before performing maintenance or any other work on the machine.

• WARNING: Rigorously follow all the instructions in this Manual (in particular those marked “Danger!” and “Warning!”). Also respect the labels applied to the machine. The Manufacturer declines all liability for injury to = persons or damage to property resulting from failure to follow instructions.
• DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner’s Manual and on your machine.
• WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner’s Manual and on your machine.
• CAUTION: Failure to read and observe all CAUTION statements could result in damage to the machine or to other property. Read and observe all CAUTION statements found in your Owner’s Manual and your machine.
• DANGER: Failure to read the Owner’s Manual prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could result as well. You must have training in the operation of this machine before using it. If you or your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine.
• DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation. Use only as described in this manual. Use only the manufacturer’s recommended attachments.
• DANGER: Machines can cause an explosion when operated near flammable materials and vapors. Do not use this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials.
• DANGER: Do not pick up flammable fluids, dust or vapors.
• DANGER: To reduce the risk of fire, electric shock, or injury, do not pick up liquids (DB3 and DB4 only).
• DANGER: Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• DANGER: This machine is not suitable for picking up health endangering dust.
• DANGER: Using a machine with a damaged power cord could result in an electrocution. Do not use the machine if the power cord is damaged. Do not use the electrical cord to move the machine. Keep cord away from heated surfaces. Do not unplug by pulling on the cord; grasp the plug, not the cord. Turn off all controls before unplugging. Do not close a door on cord or pull around sharp edges or corners.
• DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source. Disconnect the power supply before attempting any maintenance or service.
• Warning: Operating a machine without observing all labels, decals, etc., could result in injury or damage. Read all machine labels before attempting to operate the machine. Make sure all of the labels are attached or fastened to the machine. Get replacement labels and decals from the manufacturer’s distributor.
• Warning: Electrical components can “short-out” if exposed to water or moisture. Keep the electrical components of the machine dry. Always store the machine in a dry area.
• Warning: Use of this machine to move other objects or to climb on could result in injury to the opera-tor or damage to the machine. Do not use this machine as a step or furniture. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Warning: Moving parts of this machine can cause injury and/or damage. Keep hands, feet, loose clothing, hair, fingers, and all parts of the body away from openings and moving parts.
• Warning: Electrocution could occur if you handle the plug or appliance with wet hands. Do not handle plug or appliance with wet hands.
• Warning: Do not use without dust bag and or filters in place.
•  Warning: Rotating fan blades inside the cover. Before opening cover, switch off machine. Wait until the fan/brush stops completely or dust and debris may be ejected.
• Warning: If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an Authorized service center.
• Warning: Damage could occur to machine if openings are blocked. Do not put any object into openings. Do not use any opening blocked: keep free of dust, lint, hair, and anything that may reduce air flow.
• Warning: Injury could occur to the operator or the machine if used without the dust bag and/or filters in place. Do not use the machine without the dust bag and/or filters in place.
• Warning: Injury to the operator and/or damage to the machine could occur when cleaning on stairs, unless caution is used. Use extreme caution when cleaning on stairs.
•  Warning: To reduce the risk of electrical shock, always use a 3-wire electrical system connected to the electrical ground. Whenever possible connect the machine to an outlet protected by a ground fault interrupter (GFCI). See “Grounding Instructions.”

120 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground (FOR DB4, DB7, AND DB24 MODELS)
This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine has an approved power cord with three conductors and a plug with three terminals. Connect the plug to a receptacle that has three holes and is connected to the electrical ground. The green (or green and yellow) conductor in the cord is the ground wire. Never connect this wire to any terminal other than the ground terminal.
This machine uses a 120 volt AC 60 cycle electrical circuit. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has a plug as shown in Figure 1. If a receptacle connected to the electrical ground as shown in Figure 1 is not available, have one installed by an electrical contractor. Do not use an adapter.

• Warning: To reduce the risk of electrical shock, protect the machine from rain. Keep the machine in a dry area.
• Warning: To reduce the risk of electrical shock, always use a 3-wire electrical system connected to the electrical ground. Whenever possible connect the machine to an outlet protected by a ground fault interrupter (GFCI).
• Warning: Do not cut, remove or break the ground pin. If the outlet does not fit the plug, consult your electrical contractor.
• Warning: Have worn, cut or damaged cords and plugs replaced by an authorized service person.
• Warning: If it becomes necessary to use an extension cord to reach an electrical outlet, you must use one that is at least one size larger in wire size. Such as a power cord that is marked 12/3 would need to use an extension cord that is marked 10/3. Do not use an extension cord that is undersized.

GROUNDING INSTRUCTIONS (FOR DB4, DB7, AND DB24 MODELS)

IMPORTANT: Improper grounding method can result in a risk of electrical shock. This equipment shall not be used with any extension cord.
DB vacuums must be connected to a properly grounded outlet only. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of shock. DB vacuums are equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING : Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a GROUNDING PIN qualified electrician. RATED LESS THAN 15 AMPERES AND INTENDED FOR USE ON A BRANCHE DE MISE À LA TERRE
NOMINAL 120-VOLT SUPPLY CIRCUIT: the DB vacuums have a grounding attachment plug that looks like the plug illustrated. Make sure that the vacuum is connected to an outlet having the same configuration as the plug. No adaptor should be used with these vacuums.

SERVICING OF DOUBLE-INSULATED APPLICANCES (FOR DB3 MODEL ONLY)

• A double insulated appliance is marked with one or more of the following: the words “DOUBLE INSULATION” or “DOUBLE INSULATED” or the double insulation symbol (square within a square).
• In a double insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to  the appliance.
• Servicing a double insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel.
• Replacement parts for a double insulated appliance must be identical to the parts they replace.

IMPORTANT INSTRUCTIONS

• Before use, the equipment must be correctly assembled with all of its components.
• Check that the electrical outlet is correct for use with the plug on the machine.
• Before connecting, check that the specified motor voltage corresponds to the main voltage available.
• Never use the equipment near flammable, explosive or toxic substances: sparks from the motor could cause dangerous reactions.
• Always unplug the machine from the electrical outlet when leaving machine unattended or before attempting any repair.
• Service and repair should be done by qualified personnel only. Use only original manufacturer’s replacement parts.

Operation

This machine is a commercial vacuum designed for wet or dry pick up. And must be stored in a dry location.

• Machines with dual or triple vac motors can be run together or independently as the job requires.
• Dry soil can be vacuumed directly into the tank or into a disposable paper bag fitted onto the vacuum inlet.
• Only for DB7 and DB24 models: For wet pick-up, remove polyester filter. The machine is equipped with a shut-off float. As the tank is filled to capacity, a float rises and seals the vac intake, causing a loss of vacuum. Switch off the vacuum when this happens and bring the machine to a drain.
• To empty the machine, either use the drain hose mounted on the back of the tank, or remove the motor head assembly and tilt the tank backwards on tipping models, or lift and dump out the contents of smaller units.
• With both wet and dry applications be sure to frequently clean the filter. This is especially true when the vacuum is being used with strippers and floor finish.
• To reduce the risk of fire, electric shock, or injury, do not pick up liquids (DB3 and DB4 only).

After Use

1. Store the cord on the hook.
2. Store the appliance indoors, away from sources of heat.
3. This appliance is provided with an automatically reset thermal limiter to avoid damage to motor. If thermal limiter operates do one or more of the following:
   • Change the bag.
   • Clean or replace the cartridge filter.
   • Check hose and tank inlet for any obstructions.
   • Wait a few minutes for the thermal limiter to re-close the circuit.

Periodic Checks

Checks| Daily Operations| Weekly Operations| Six Monthly Operations
---|---|---|---
Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning| | | X
Inspect gasket seals and replace those which have begun to leak| | | X
Examine carbon motor brushes and commutator| | | X

Servicing The Filter
The filter is accessed by lifting the head assembly off the tank. The Polyester filter assembly is easily removed by simply lifting the filter basket out of the tank. The cartridge filters they are removed very easily. First remove the filter retainer by turning the black knob 90 degrees counter-clockwise. The cartridge filter will then slide off of the support assembly.

• Be sure to frequently clean the filters.
• Allow filters to thoroughly air dry after washing them before returning them to the machine.
• Worn filters can affect vacuum performance. Replace the filters when they become worn out and normal cleaning will not restore vacuum performance.

Servicing The Vac Motor

Motor Replacement :

1. Disconnect power cord from power source.
2. To access the vac motor, remove the screws that attach the main cover to the head assembly and set the over to one side.
3. Remove the screws that attach the inner cover to the head assembly and set aside.
4. Remove the carbon brush assembly by removing the 2 screws that attach it to the vac motor.
5. Slide off the carbon brush connector from the motor terminal.
6. Inspect armature commutator. If it is extremely pitted, grooved or not concentric then the motor will need to be replaced or sent to a qualified service center.
7. Reverse steps 6 through 4 to install new carbon brush and housing.
8. Repeat steps 4 through 7 for the other carbon brush.
9. Reverse steps 3 and 2 for re-assembly.
10. Test for proper operation.
    SAVE THESE INSTRUCTIONS

Vacuum Warranty

Dustbane Products Ltd.

• Your new product from Dustbane Products Limited is covered by a full warranty from the date of purchase. This includes all new units and accessories (some exceptions apply) manufactured or supplied by Dustbane Products Limited and delivered to the original retail purchaser by an authorized Dustbane distributor. Should your product have a defect in material or workmanship under normal use and care within the warranty period outlined below,
• Dustbane shall arrange to have the original product returned to our head office or to an authorized service center for repair, replacement or refund.

WHAT IS COVERED

• Tanks
  ONE (1) YEAR warranty on all equipment parts against defects in material and workmanship under normal use and care.

• Parts
  ONE (1) YEAR warranty on all equipment parts against defects in material and workmanship under normal use and care.

• Labour
  ONE (1) YEAR warranty on labour based on Dustbane’s Labour Rates and equipment parts under normal use and care.

• Electrical Components
  ONE (1) YEAR warranty on electrical components under normal use and adequate storage methods.

• Vac Motor
  ONE (1) YEAR OR UP TO 850 HOURS warranty on vac motor under normal use and care.

• Wheels and Casters
  ONE (1) YEAR warranty on equipment wheels and casters under normal use and care.

The provisions of this Warranty shall not apply to:

• any unit of Dustbane Equipment which has been subject to misuse, negligence, accident, use of inappropriate accessories, parts or chemicals, or service by an unauthorized Dustbane repair depot.
• normal maintenance services and the replacement of service items (including but not limited to electric cord, painted parts, any rubber parts and springs, switch and bearings) made in connection with such services as required in the Dustbane Recommended Maintenance Schedule.
• travel time
• the followina parts and/or accessories are not covered under the warranty:
• Rubber parts
• Electric cord
• Switch Gaskets
• External Hoses
• Springs
• Painted parts
• Bearings
• Filters

Use this card for quick access to your product information (information purposes only)

WARRANTY CARD

• Model Name:
• Model Number:
• Serial Number:
• Date of Purchase:
• Purchased From:

HEAD

Ref.

|

Part N.

| HEAD

Description

|

Qty

---|---|---|---
1| 3MECB01727| CABLE E.2X16AWG SJT MT8,5 N1-15| 1
2| 3MEVR28673| STRAIN RELIEF| 1
3| 3VTVT71960| SCREW PAT TMT PHL M5X14 ZN BLACK| 4
4| 3MPVR11943| HANDLE DB3 VAC| 1
5| 3MPVR11667| COVER DB3 VAC| 1
6| 3GUVR00404| ADHESIVE GASKET COVER| 1
9| 3FTDP00506| CARTRIDGE HEPA 140X70X20| 1
10| 3MPVR11757| BRACKET DB3 VAC| 1
11| 3FTDP40010| FILTER PPI/80 D.115X20| 1
12| 3MEVR40111| GUIDING SLIT W/LEO MEMBRANE| 1
13| 3VTVT71961| SCREW PFU TMT PHL 5X20 BLACK| 3
14| 3VTVT71961| SCREW PFU TMT PHL 5X20 BLACK| 2
15| 3MPVR28690| CABLE CLAMP| 1
16| 3MECI00651| SWITCH BUTTON| 1
17| 3MPVR11669| MOTOR FASTENER| 1
20| 3MEVR40111| GUIDING SLIT W/MEMBRANE| 1
21| 3MPVR40559| MOTOR FASTENER M30 D42X20| 1
22| 3MOMO00917| MOTOR TS202 K 800W 120V 60HZ| 1
23| 3GUGO00505| GASKET D.130 H=13| 1
24| 3GUGO40053| O-RING SPONGE RUBBER D.4 D.190| 1
25| 3MPVR10300| BASE| 1
26| 3VTVT71966| SCREW PAT TMT PHL 5X30 BLACK| 6
27| 3GUVR40077| GASKET FOR BASE| 1
28| 3MPVR06885| CLIP BIG FIXING CABLE| 1

KIT BASKET

TANK

PAPER FILTER

KIT

HEAD

Ref.

| ****

Part N.

| HEAD

Description

| ****

Qty

---|---|---|---
| 3FSVR00127| CLAMP| 1
| 3MECB01830| MOTOR WIRING 40CM POKE-IN UL| 1
| 3MECB01686| CONN.WIRE M.AWG-400-G/V-SP9-4,2| 1
1| 3MPVR13334| HANDLE TOPPER 500 AZZURRO AU| 1
2| 3VTVT71961| SCREW PFU TMT PHL 5X20 ZN NERA| 1
3| 3MECI72195| ANTISPLASH SWITCH| 1
4| 3VTVT71961| SCREW PFU TMT PHL 5X20 ZN NERA| 2
5| 3VTVT40007| SCREW PAT TMT PHL 5X55 BLACK| 2
5| 3MPVR11834| COVER TOPPER 500 NE AU| 1
7| 3VTVT01453| SCREW VITE TC PZ 4,2X16 ZN NERA| 1
8| 3MECV35825| ELECTRIC CORD 3X16 AWG| 1
9| 3MEVR02216| FAIR-LEAD LONG| 1
10| 3MPVR28690| CABLE CLAMP| 1
11| 3VTVT71961| SCREW PFU TMT PHL 5X20 ZN NERA| 1
12| 3MECB01155| TERMINAL BOARD 300-500 3P AWG S/R| 1
13| 3FTDP38064| FILTER MTP/65 H=15 D.95| 1
14| 3VTVT71971| SCREW PAT TMT PHL 5X35 BLACK| 6
15| 3MPVR13336| COVERING 99 S/FORI AU AZZURRO| 1
16| 3MPVR38371| WASHER H8 D85X65| 1
17| 3FTDP38066| FILTER PHONO H=75| 1
18| 3VTVT71971| SCREW PAT TMT PHL 5X35 BLACK| 6
19| 3VTVT71961| SCREW PFU TMT PHL 5X20 ZN NERA| 4
20| 3MPVR08400| MOTOR FASTENER 500 AU. NERO| 1
21| 3GUGO28683| “L” GASKET W/O HOLES H=5,5| 1
22| | MOTOR BD381 AU 1000W 120/60| 1
23| 3VTRS00393| TOOTHED WASHER M4 UNI 8842| 1
24| 3VTVT01037| SCREW TC CROSS M 4X8 UNI 7687| 1
25| 3GUGO28683| “L” GASKET W/O HOLES H=5,5| 1
26| 3FTDP38067| WASHER MTP 65MM 18D 230X145| 1
27| 3PMBA00116| BASE 500 AU C/GUAR. NERO| 1

FILTERING KIT

TROLLEY

KIT

Ref.

| ****

Part N.

| FILTERING KIT

Description

| ****

Qty

---|---|---|---
A| 3MPVR09568| RING 500 W/POLY.FIL.H=75| 1
1| 3MPVR36522| FILTER RING 500| 1
2| 3FTDP00451| FILTER POLYESTER H=75 SAN| 1
3| 3MPVR28830| BASKET FOR FILTER P.| 1
4| 3VTVT71971| SCREW PAT TMT PHL 5X35 BLACK| 4
5| 3FTDP00481| FILTER PPI/20 D.115| 1

Ref.

| ****

Part N.

| TANK

Description

| ****

Qty

---|---|---|---
1| 3PMVR06254| DRUM PL.200/16D NE| 1
2| 3MPVR09033| BL.PIPE UNION R155 C/PUL.AZ| 1
3| 3GUGO28701| GASKET D.38| 1
4| 3GUGO28736| GASKET R 205 BLACK| 1
5| 3MPVR28696| DEFLECTOR 99| 1
6| 3VTVT71966| SCREW PAT TMT PHL 5X30 BLACK| 4
7| 3CHVR28735| COMPLETE PLASTIC HOOK BLACK| 2
8| 3VTVR71992| RIVET RIVET 4,8X17| 4

Ref.

| ****

Part N.

| TROLLEY

Description

| ****

Qty

---|---|---|---
1| 3MPVR40522| TROLLEYTROLLEY BODY 500 VEGAS BL| 1
2| 3RTRT42006| TROLLEY BOX WHEEL| 2
3| 3RTRT85778| WHEEL BODY YES| 2
4| 3MPVR40523| WHEEL COVERING YES BLACK| 2
5| 3VTVT71960| SCREW SCREW PAT TMT PHL 5X14 ZN| 4
6| 3MPVR11783| EXTENSION INN. SPAZZOLA CARR.VEGAS| 1
| | PAPER FILTE| R
---|---|---|---
Ref.| Part N.| Description| Qty
1| 3FTDP33284| PAPER BAG 101/BOX| 1

HEAD

FILTERING KIT

TANK

TROLLEY

PAPER FILTER

Ref.

| ****

Part N.

| TANK

Description

| ****

Qty

---|---|---|---
1| 3PMVR06256| DRUM PL.500/27W C/Q NE| 1
2| 3MPVR09033| BL.PIPE UNION R155 C/PUL.AZ| 1
3| 3GUGO28701| GASKET D.38| 1
4| 3GUGO28736| GASKET R 205 BLACK| 1
5| 3MPVR28696| DEFLECTOR 99| 1
6| 3VTVT71966| SCREW PAT TMT PHL 5X30 BLACK| 4
7| 3CHVR28735| COMPLETE PLASTIC HOOK BLACK| 2
8| 3VTVR71992| RIVET RIVET 4,8X17| 4

Ref.

| ****

Part N.

| TROLLEY

Description

| ****

Qty

---|---|---|---
1| 3MPVR40522| TROLLEYTROLLEY BODY 500 VEGAS BL| 1
2| 3RTRT42006| TROLLEY BOX WHEEL| 2
3| 3RTRT85778| WHEEL BODY YES| 2
4| 3MPVR40523| WHEEL COVERING YES BLACK| 2
5| 3VTVT71960| SCREW SCREW PAT TMT PHL 5X14 ZN| 4
| | PAPER FILTE| R
---|---|---|---
Ref.| Part N.| Description| Qty
1| 3FTDP72226| PAPER BAG 101/BOX| 1

DO ALL TOOL

Ref.

| ****

Part N.

| DO ALL TOOL

Description

| ****

Qty

---|---|---|---
1| 3MPVR06726| BRUSH BODY 400| 1
2| 3MPVR49176| ELASTIC RING NUT BRUSH 400| 1
3| 3MPVR02289| BRUSH 400 ELBOW CLUTCH D.38| 1
4| 3MPVR06728| WHEEL HOLDER SUPPORT BRUSH 400| 2
5| 3VTVT01193| SCREW PAT TMT PHL 5X15 ZN BLACK| 4
6| 3RTRT87117| WHEEL D.25 BRUSH 300/400| 2
7| 3LAFN86068| PIVOT 5 X 17,5 ZN| 2
8| 3MPVR38641| GUIDE LIST W/WET L=395| 2

CARPET TOOL

Ref.

| ****

Part N.

| CARPET TOOL

Description

| ****

Qty

---|---|---|---
1| 3MPVR06726| BRUSH BODY 400| 1
2| 3MPVR49176| ELASTIC RING NUT BRUSH 400| 1
3| 3MPVR02289| BRUSH 400 ELBOW CLUTCH D.38| 1
4| 3MPVR06728| WHEEL HOLDER SUPPORT BRUSH 400| 2
5| 3VTVT01193| SCREW PAT TMT PHL 5X15 ZN BLACK| 4
6| 3RTRT87117| WHEEL D.25 BRUSH 300/400| 2
7| 3LAFN86068| PIVOT 5 X 17,5 ZN| 2
8| 3SPPV76601| STRIP L=395| 1
9| 3SPPV76599| GUIDE LIST W/STRIP L=395| 1

KIT

HEAD

FILTERING KIT

__

Ref.

| __

Part N.

| FILTERING KIT

Description

| __

Qty

---|---|---|---
A| 3FTDP28733| KIT RING+FILT+BASK.400 CONIC.SAN| 1
1| 3MPVR35807| FILTER RING 400| 1
2| 3FTDP00523| FILTER POLY AN4-600 CON REG H320| 1
3| 3MPVR09199| CONICAL BASKET 400| 1
4| 3MPVR40521| NET ANTIFOAM BODY HIGH| 1
5| 3RCGR40008| HIGH FLOAT 99 W/GASKET 37 SHA| 1
6| 3MPVR35796| BUSHING PLASTIC SLEEVE D.8| 4
7| 3VTVT36751| SCREW SCREW PAT TMT PHL 5X25| 4

DO ALL TOOL

__

Ref.

| __

Part N.

| DO ALL TOOL

Description

| __

Qty

---|---|---|---
1| 3MPVR06726| BRUSH BODY 400| 1
2| 3MPVR49176| ELASTIC RING NUT BRUSH 400| 1
3| 3MPVR02289| BRUSH 400 ELBOW CLUTCH D.38| 1
4| 3MPVR06728| WHEEL HOLDER SUPPORT BRUSH 400| 2
5| 3VTVT01193| SCREW PAT TMT PHL 5X15 ZN BLACK| 4
6| 3RTRT87117| WHEEL D.25 BRUSH 300/400| 2
7| 3LAFN86068| PIVOT 5 X 17,5 ZN| 2
8| 3MPVR38641| GUIDE LIST W/WET L=395| 2
Ref.| Part N.| Description| Qty
---|---|---|---
29| 3GUGO28683| “L” GASKET W/O HOLES H=5,5| 2
30| 3MPVR08575| FAKE MOTOR LOWERED AU| 2
31| 3FTDP38057| ANTINOISE TRIANGLE H=51| 3
32| 3FTDP28745| GASKET MTP/30 AU-AD 50X10X85| 3
33| 3MPVR38058| BASE CAP| 2
34| 3PMBA00209| BASE 600/400 AU NE COMP| 1

TANK

KIT

KIT

PAPER FILTER

CARPET TOOL

Ref.

| ****

Part N.

| KIT

Description

| ****

Qty

---|---|---|---
1| 3TBFX01166| FLEXIBLE HOSE N2,5-3838G38 TYPE| 1
2| 3LAFN43048| WAND| 2
3| 3MPVR43047| PISTOL GRIP| 1
4| 3SPPV00156| CREVICE TOOL| 1
5| 3SPPV43052| ROUND BRUSH| 1
6| 3SPPV43050| CARPET TOOL| 1
7| 3SPPV43051| DO ALL TOOL| 1
8| 3MPVR43049| PVC ADAPTOR D.38| 1

Ref.

| ****

Part N.

| KIT

Description

| ****

Qty

---|---|---|---
*| 3PLDC03239| | 1
1| 3MPVR08170| HOSE HOLD.CLIP D36-38 BLACK| 2
2| 3VTVT71960| SCREW SCREW PAT TMT PHL 5X14 ZN| 4
| | PAPER FILTE| R
---|---|---|---
Ref.| Part N.| Description| Qty
1| 3FTDP28862| PAPER BAG FILTER 400| 1

Ref.

| ****

Part N.

| CARPET TOOL Description| ****

Qty

---|---|---|---
1| 3MPVR06726| BRUSH BODY 400| 1
2| 3MPVR49176| ELASTIC RING NUT BRUSH 400| 1
3| 3MPVR02289| BRUSH 400 ELBOW CLUTCH D.38| 1
4| 3MPVR06728| WHEEL HOLDER SUPPORT BRUSH 400| 2
5| 3VTVT01193| SCREW PAT TMT PHL 5X15 ZN BLACK| 4
6| 3RTRT87117| WHEEL D.25 BRUSH 300/400| 2
7| 3LAFN86068| PIVOT 5 X 17,5 ZN| 2
8| 3SPPV76601| STRIP L=395| 1
9| 3SPPV76599| GUIDE LIST W/STRIP L=395| 1

Tools & Accessories

Vacuums

Dustbane Customer Support

• Mailing Address 1000 Last Mile Drive, Ottawa, Ontario, K1G 6Y1
• Canada
• Phone
• 1-800-387-8226
• Email
• General Inquiries: info@dustbane.ca
• Technical Inquiries: techsupport@dustbane.ca
• Website
  www.dustbane.ca

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>