Sentiotec Medium – 196 Solid wood sauna Family All in Set Installation Guide

: July 16, 2024
: sentiotec

Table of Contents

Preparing for installation
Parts list for Family Medium All in Set
Parts list for Family Large All in Set
Floor plan for Family Medium All in Set
Floor plan for Family Large All in Set
Assembling the cabin
Family Medium All in Set
Family Large All in Set
Documents / Resources

Solid wood sauna
Family All in Set
Medium – 196 x 159 x 204 cm
Large – 196 x 189 x 204 cm
INSTRUCTIONS FOR INSTALLATION
Version 02/24
FAMILY-SET

Preparing for installation

Read these assembly instructions carefully and keep them within reach when using the sauna so that you can look up product information at any time.
These installation instructions can also be found in the downloads section of our website: www.sentiotec.com/downloads .

1.1. Important note

Before you begin work, check the parts list to ensure that all the individual parts have been delivered. If you discover any missing parts, notify your dealer within 14 days of receiving the sauna cabin.
The room in which the sauna is installed must be dry and ensure an appropriate amount of air circulation.
The floor must be level and even, preferably a stone or tiled floor.
A minimum cabin height of 230 cm is required for the cabin installation work.
A distance of at least 5 cm from the wall must be maintained.
The inside of the wooden parts used must not be handled with any impregnating material.
Wood is a natural product that can swell, shrink or warp, despite good storage.
For this reason, some force may be necessary during the installation.
Air circulation in the sauna cabin is crucial for correct function. Please observe the dimensions for the air intake and outlet vents specified by the manufacturer of the sauna heater. If necessary, cut a rectangular cutout into the base frame before installation; Holes can also be made later using a drill.
You will need good manual skills and an assistant for the installation.
All screw fittings must be pre-drilled.

Attention!
The electrical connection may only be performed by a qualified electrician or similarly qualified person.

1.2. Tools required

Hammer with a wooden head or a mallet
Cordless screwdriver with bits for cross-head screws and Torx
Roller tape measure
Drill bits with a diameter of 3 mm, 10 mm, 20 – 30 mm (for sauna heater power cable)
Spirit level
1.5mm hexagonal socket wrench
Utility knife
Ladder

| This symbol indicates tips and useful information
---|---
| Back-to-front assembly
| Pre-drill
| Carry out wiring
| Cut to actual measurement with saw

Check the right angle:

Handle glass with care: Special care must be taken with the edges of the glass – hardened glass can shatter into small pieces in the event of impact. Insert protective cushioning (eg: cardboard box) under the edge of the glass.

1.3. Maintenance and cleaning

The sauna should be cleaned inside with a damp cloth. Use warm water only – if required, we recommend Harvia Sauna Cleaner (SAC25040 – Cleaning and disinfection)
If the sauna will not be used for an extended period, we recommend heating the cabin once a month to prevent the formation of mold.
Pitch pockets are not grounds for return, since they can always appear in spruce wood and the depth at which they lie cannot be detected during the sorting-out process.

If these are just under the surface, heat can cause them to soften and “bleed”.
The leaking pitch can be removed with a rag soaked in acetone. If only droplets of pitch occur, allow them to harden and then carefully scrape them off with a knife.

1.4. Disposal

Dispose of packaging materials in accordance with the applicable waste disposal regulations.
Used devices contain reusable materials as well as hazardous substances.
Therefore, do not dispose of your used device with household waste, but do so in accordance with the locally applicable regulations.

Parts list for Family Medium All in Set

No. of items	Name	Dimensions (cm)

Wall elements
1| Wall element, bottom right – Electrical element| 154.5x102x4
1| Wall element, top right – Electrical element| 154.5x108x4
1| Wall element, bottom rear – Ventilation element| 185×88.5×4
1| Wall element, top rear| 185×121.5×4
1| Wall element, bottom left – Electrical element| 154.5x102x4
1| Wall element, top left – Electrical element| 154.5x108x4
1| Above door element, black| 173×12.1×4
1| Element with groove for glass, right, black| 202.5x6x4
1| Element with groove for glass, left, black| 202.5x6x4
1| Mounting rail above door, black| 59.7×1.8×0.8
1| Cover, front with cut-out, black| 202.5×11.5×4
1| Cover, front, black| 202.5×11.5×4
1| Cover, top front, black| 175×10.6×4
Roof elements
2| Roof element| 146.7x92x5.6
Glass elements
1| Glass door| 190x59x0.8
1| Glass element with holes for door hinges| 193x58x0.8
1| Glass element| 193x58x0.8
Support slats
3| Bench support slats| 57x4x4
2| Bench support slats| 88.5x4x4
2| Roof support slats| 138.5x4x4
1| Roof support slat| 185x4x4
1| Roof support slat with LED| 185x4x4
4| Cover slats, outside corners| 202.5x8x1.5
2| Cover slats, outside, top| 138.5x8x1.5
1| Cover slat, inside, top| 145.5x8x1.5
Interior fittings

Parts list for Family Large All in Set

No. of items	Name	Dimensions (cm)

Wall elements
1| Wall element, bottom right – Electrical element| 185x102x4
1| Wall element, top right – Electrical element| 185x108x4
1| Wall element, bottom rear – Ventilation element| 185×88.5×4
1| Wall element, top rear| 185×121.5×4
1| Wall element, bottom left – Electrical element| 185x102x4
1| Wall element, top left – Electrical element| 185x108x4
1| Above door element, black| 173×12.1×4
1| Element with groove for glass, right, black| 202.5x6x4
1| Element with groove for glass, left, black| 202.5x6x4
1| Mounting rail above door, black| 59.7×1.8×0.8
1| Cover, front with cut-out, black| 202.5×11.5×4
1| Cover, front, black| 202.5×11.5×4
1| Cover, top front, black| 175×10.6×4
Roof elements
2| Roof elements| 177.2x92x5.6
Glass elements
1| Glass door| 190x59x0.8
1| Glass element with holes for door hinges| 193x58x0.8
1| Glass element| 193x58x0.8
Support slats
3| Bench support slats| 57x4x4
2| Bench support slats| 114x4x4
2| Roof support slats| 169x4x4
1| Roof support slat| 185x4x4
1| Roof support slat with LED| 185x4x4
4| Cover slats, outside corners| 202.5x8x1.5
2| Cover slats, outside, top| 169x8x1.5
1| Cover slat, inside, top| 176x8x1.5
2| Benches| 184x57x8
---|---|---
1| Bench| 113x57x8
1| Bench foot| 57x94x6
1| Heater protection grid| 50x73x5
2| Heater protection grid| 32.2x43x5
1| Cover, IR radiators| 69x21x5
Accessories
1| Headrest| 30x28x7
1| Door handle set lime wood/black wood|
1| LED RGBW – integrated into roof support slat| 185×2.1×1.7
1| LED technology 40W (white)| LED set 230V S/D 40W
1| 4 linear m silicone cable 5×2.5mm²|
1| Cable cover slat| 200x4x3
1| Ventilation slit| 56x14x1.5
1| Door magnet, sleeve plate, black|
2| Door hinges 8652-05, black|
2| Aluminum U-profile, black| 56.7
1| Installation material set|
1| Assembly instructions|
Technology
1| Sauna heater sentiotec 190E, 9 kW| ST190400BE
1| Finnish sauna stones| R-990
1| Sauna control unit PRO-D2I| PRO-D2I
1| Bench sensor| O-F2
1| Control panel additional output (IR radiators)| PRO-DA-CU
1| ECO IR radiator 350W| ECO-350-R

Floor plan for Family Medium All in Set

4.1. Floor plan Medium “left”

Sentiotec Medium - 196 Solid wood sauna Family All in Set -
Medium 4.2. Floor plan Medium “right”

Sentiotec Medium - 196 Solid wood sauna Family All in Set - Floor plan
Medium

Floor plan for Family Large All in Set

5.1. Floor plan Large “left”

Sentiotec Medium - 196 Solid wood sauna Family All in Set - Floor plan for
Family Large 5.2. Floor plan Large “right”

Assembling the cabin

ATTENTION!
The cabin is designed for both “right-hand” and “left-hand” assembly.
Please observe the floor plans on pages 10 and 11, depending on model.
Observe the figures starting on page 17.

6.1. Installing wall elements
Start assembly with the “Wall element, bottom rear – Ventilation element” and the “Element, bottom right”. The lower parts can be identified by the projecting connecting strips. Screw the elements at a right angle (see tip on page 4) from
outside. Repeat this with the left side wall. The rear wall is thus installed between the side walls.
When assembling the upper sections, again start with the rear wall (Element, top rear). Make sure this is flush with the connecting strip of the lower rear wall.
Screw both sides of the upper rear wall to the projecting strip of the lower rear wall.
Screw the upper wall elements together.
Note that each upper wall element must be screwed to the protruding strip of the lower wall element.

6.2. Assembling the glass elements
Screw the “Elements with groove for glass” to the side walls from outside. Fit the “Element above door” and additionally screw in from above.
Fit the aluminium U-profiles flush with the glass elements.
Please note that when you install the “glass element with holes for door hinges”, you are defining the direction in which the door opens (see option 1 and 2).
Position the glass element centrally in the door frame, paying attention to straight alignment and the position of the struts. Slide the glass element to the left or right, respectively, into the groove in the corner posts.
Insert the “Mounting rail above door” between the glass elements.
6.3. Completing the cabin exterior
Install the “Covers, front” by screwing from the inside – flush with the inner side.
Pay attention to the element with cut-out for the control panel – this can be fitted on the left or right.
Install the “Cover, top front” above the glass by screwing from the inside.
Mount the “Cover slats, outside” using screws.
6.4. Roof installation
Install the roof support slats. Start with the LED strip on the rear wall.
Insert the roof elements and screw them to the cabin walls. Observe the cable outlets.
Install the cover slat, inside.
6.5. Installing interior fittings
Install the infrared radiator. Fit the radiator flush with the rear side of the radiator cover. Position the radiator cover in the cut-out and screw it to the rear wall.
**** Please note that the terminal box for the radiator must be at the top.

Mount the ventilation slide.
Install the bench support slats.
Place the upper and lower benches on the bench support slats provided for this purpose.
Screw the bench foot to the upper angled bench and screw the other end of this to the rear upper bench. Finally, screw the bench foot to the wall element.
6.6. Installing the electrical equipment
You need a hole measuring Ø 2 cm in the cable shaft for the heater supply cable.
Drill the cable outlet at a right angle and route the cable as far as the roof to the power unit for the sauna control (5 x 2.5 mm).
Repeat for the heater sensor – Ø 1 cm – 15 cm below the ceiling.
Repeat for the bench sensor – Ø 1 cm, opposite the heater sensor on the rear2 wall – 15 cm below the ceiling.
To cover the cables, use the cable cover slat. Shorten them with a saw as required.
Route the data cable for the control panel up to the cabin roof, to the power unit for the sauna control.

6.7. Installing the glass door
Screw the two door fittings onto the glass element, making sure that they are straight and that the doors open outward.
The alignment of the fittings is achieved by adjusting / rotating both plastic inserts.

6.8. Installing accessories
The door handles are screwed together from the inside.
Fit the door magnet and sleeve plate. There are mounting holes under the seal for the door magnet; the seal needs to be cut to the left or right depending on how the door opens.
Assemble the protection grille.
Install the cable cover slat as required.

6.9. Connecting the electrical equipment

Observe the operating instructions for your sauna heater and the sauna control.
ATTENTION!
Installation may only be performed by a qualified electrician or similarly qualified person.

Sentiotec Medium - 196 Solid wood sauna Family All in Set -
Installation

Power supply unit for PRO D2i

Sentiotec Medium - 196 Solid wood sauna Family All in Set - Power supply
unit for PRO D2i

Family Medium All in Set

Sentiotec Medium - 196 Solid wood sauna Family All in Set - Family Medium
All in Set1

Family Large All in Set

Sentiotec Medium - 196 Solid wood sauna Family All in Set - Family Medium
All in Set2 |
---|---
|
|
|
|
| Sentiotec Medium - 196 Solid
wood sauna Family All in Set - fig3
|

sentiotec GmbH Division of Harvia Group
Wartenburger Straße 31, A-4840 Vöcklabruck
T +43 (0) 7672/22 900-50 | F -80
info@sentiotec.com www.sentiotec.com

Documents / Resources

| Sentiotec Medium - 196 Solid wood sauna Family All in Set [pdf] Installation Guide
Medium - 196 Solid wood sauna Family All in Set, Medium - 196, Solid wood sauna Family All in Set, sauna Family All in Set, Family All in Set, All in Set, in Set, Set
---|---