HOUSE OF ROHL INS11711A 1/2 Inch Pressure Balance Trim Instruction Manual

HOUSE OF ROHL INS11711A 1/2 Inch Pressure Balance Trim

Product Specifications

• Product Name : 1/2 Pressure Balance Trim
• Model: 51 Trim Sets (style varies)

Product Usage Instructions

Helpful Tools:
For safety and ease of installation, it is recommended to use the following tools:

• Phillips Screwdriver
• 2mm Allen Wrench

Installation:
Follow these steps for proper installation:

1. If installing on a standard wall, remove Valve Cover and Plaster Ground (C). If installing on an acrylic wall, remove Valve Cover (C).
2. Open water for 20 seconds.
3. Remove test plug (B) from Valve Assembly. Turn off stops and remove test plug for flushing.
4. Install Cartridge Puck (F) and Cartridge (G) into the Valve Assembly with red inlet on the left and blue inlet on the right. Ensure correct installation of Cartridge ends.
5. Turn the Cartridge 1/4 turn.
6. Install the Wall Plate (E) onto the Mounting Bracket Assembly and then install the Rosette (J).

FAQ

Where can I find additional support or warranty information?

• US Customers:
  • houseofrohl.com/support
  • 1-800-777-9762
• Canadian Customers:
  • houseofrohl.ca/support
  • 1-866-473-8442 (Canada)
  • 1-800-287-5354 (Ontario)

HELPFUL TOOLS
For safety and ease of installation, the use of these helpful tools is recommended.

Parts List

• A. Valve Assembly
• B. Valve Test Plug
• C. Valve Cover and Plaster Ground
• D. Mounting Bracket Assembly
• E. Wall Plate
• F. Cartridge Puck
• G. Cartridge
• H. Decorative Sleeve
• I. Handle Dome
• J. Rosette
• K. Handle
• L. Handle Set Screw

INSTALLATION INSTRUCTION

OPTIONS OF INSTALLATION

• STANDARD WALL

• ACRYLIC WALL

INSTRUCTION

1. A. If installed with a standard wall, remove Valve Cover and Plaster Ground (C).
   B. If installed with an acrylic wall, remove Valve Cover (C).

2. Remove test plug (B) from Valve Assembly. Turn off stops. Remove test plug for flushing.

3. Suggested: Open stop. Flush the hot and cold supplies 20 seconds each.

4. With stops in the close or vertical position, install Cartridge Puck (F) and Cartridge (G) into the Valve Assembly. Red inlet will be on the left, blue inlet will be on the right. Ensure that the ends of the Cartridge are installed correctly. Red marking on the Cartridge to be installed on the hot water line. Blue marking on the Cartridge to be installed on the cold water line.

5. Slide Cartridge Nut onto Cartridge and hand tighten.

6. Do not overtighten the cartridge nut. Mark a line on the nut and body. With a wrench, rotate the nut closed 1/4 turn. Turn on the stops and check for leaks.

7. Install Decorative Sleeve (H) and Handle Dome (I). Tighten dome, hand tight only. Orient the Handle Dome as shown.

8. Install the Mounting Bracket Assembly (D) and secure with Mounting Bracket Assembly Screws (x2). Shorten the screws as needed. Apply sealant to the edges.

9. Install the Wall Plate (E) onto the Mounting Bracket Assembly. Once the Wall Plate is installed, install the Rosette (J).

10. Install the Handle (K). Once the Handle is installed, insert and tighten the Handle Set Screw (L) to the underside of the Handle.

11. Installation is complete.
    
    

ABOUT COMPANY

For warranty or additional information, contact:

• US Customers
  • U.S.A.
  • houseofrohl.com/support
  • 1-800-777-9762
  • QUEBEC / MARITIMES / WESTERN CANADA:
  • houseofrohl.ca/support
  • 1-866-473-8442
• Canadian Customers
  • ONTARIO
  • houseofrohl.ca/support
  • 1-800-287-5354

References

• Support | House of Rohl
• Support | House of Rohl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>