MAF THREE 3D Scanner User Guide

: September 2, 2024
: MAF

Table of Contents

MAF THREE 3D Scanner
Product Information
OVERVIEW
Software
Setup
Connecting to Your Network
Connection Alternative
3D Scanning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MAF THREE 3D Scanner

Product Information

Software: The THREE scanner does not require any additional software installation. The software is embedded within the hardware itself and can be accessed through a modern web browser when connected to a home network.

Specifications

Power Plugs: International
Calibration Cards: Large and Small
Accessories: Antenna, AC power adapter, Tripod
Scanner Type: THREE 3D Scanner

Setup Instructions

Select the appropriate power plug and connect it to the AC power adapter.
Attach the antenna to the 3D scanner.
Connect the tripod to the 3D scanner.
Plug in the power adapter to the scanner.
Attach the turntable wire connector to the magnetic port on the scanner.
Place the large calibration card in front of the scanner.
Power on the scanner and wait for the software updates to be checked.

Connecting to Your Network – Wireless

The scanner will create a WIFI hotspot named MAF_THREE. Connect your computer to this hotspot.
Enter the IP address projected by the scanner into your web browser.
Follow the on-screen instructions to select your WIFI network and enter the password.
The scanner will disconnect from the hotspot and connect to your WIFI network using the provided password.

Frequently Asked Questions (FAQ)

Q: Does the THREE scanner require additional software installation?
A: No, the THREE scanner does not require any software installation as the software is integrated into the hardware itself.
Q: What should I do if I encounter issues connecting to my WIFI network?
A: Make sure you are entering the correct password for your WIFI network. If issues persist, contact customer support for assistance.

OVERVIEW

Turntable
International power plugs
Large calibration card
Calibration card stand
Small calibration card
THREE 3D Scanner with antenna attached
AC power adapter
Tripod

Software

The THREE has NO software to install or download. THREE is NOT a cloud service. Instead the software is built into the THREE scanner hardware itself. To access it, connect the THREE to your home network and use any modern web- browser. Please read and follow the directions below carefully, to learn how to connect THREE to your WIFI network.

Setup

Select the appropriate power plug for your region and connect it to the AC power adapter.
Attach the antenna to the 3D scanner.
NOTE: Never store the 3D scanner in the carrying case with the antenna connected.
Attach the tripod to the 3D scanner.
Plug in the power adapter to the 3D scanner.
Attach the turntable wire connector to the magnetic port on the 3D scanner. (Figure 2.)
Attach the large calibration card to the slot in the calibration card stand and place it in front of the 3D scanner. (Figure 3.)
Press the power button. The 3D scanner will project the THREE triangle logo and then check for software updates.

Connecting to Your Network

Option 1 – Wireless

The 3D scanner will start a WIFI hotspot called MAF_THREE and project an IP address. Connect your computer to the WIFI hotspot MAF_THREE. (Figure 4.)
Open your web browser and enter the IP address projected by the 3D scanner.
Follow the instructions on the website to select your WIFI network and enter its password. (Figure 5.)
MAF_THREE hotspot will disconnect and the 3D scanner will attempt to connect to the selected WIFI network using the password you provided. Your computer will disconnect from MAF_THREE.
If necessary, reconnect your computer to your WIFI network.
When the 3D scanner successfully connects to your WIFI network it will project a new IP address. Open the IP address in your web browser. This accesses the 3D scanner’s built-in website, which provides software control for 3D scanning and managing your scans. (Figure 6.)
If the 3D scanner does not successfully connect to WIFI, it is because of an incorrect password or because the network is no longer available. In this situation the 3D scanner will restart the WIFI hotspot MAF_ THREE. Repeat the connection process from Step 1.

Option 2 – Ethernet

Connect the 3D scanner using an ethernet cable (not included).
Connect the ethernet cable to the 3D scanner, and then connect the other end to your router. (Figure 7.)
Open your web browser and enter the IP address projected by the 3D scanner.
Optionally: Click on the “hamburger menu” (the three horizontal lines) at the top-left corner of the page. (Figure 8.)
Optionally: Choose “Network”, then click on WIFI and select your WIFI network and enter its password.
Optionally: When the 3D scanner successfully connects to your WIFI network it will project “Connected” with an IP address. Type the IP address in your web browser to connect using WIFI.
Optionally: You may disconnect the ethernet cable and use THREE via WIFI.

Connection Alternative

Direct Ethernet Connection

Connect an ethernet cable (not included) to the 3D scanner and to your computer’s ethernet port.
Once connected, open the IP address projected by the 3D scanner. You may choose to connect the 3D scanner to WIFI as per the instructions above. Please Note, this may not work for all devices.

Hotspot Only
You may optionally use the 3D scanner by connecting to its hotspot and not connecting it to WIFI. This configuration is not recommended because you will not have internet access on your computer and THREE will not have internet access to check for software updates.

Connect your computer to the THREE’s WIFI hotspot MAF_THREE.
Use a web-browser to open the projected IP address.
When prompted choose not to connect to WIFI.

3D Scanning

Once connected to the 3D scanner follow the built-in tutorial instructions to scan, process and export.

Product Information
Please read the “Important Product Information” booklet for safety and warranty information.