HAUNTED LIVING KL-99001 3.5-FT Lighted Kraken with Tentacles User Manual

September 2, 2024
HAUNTeD LiViNG

HAUNTED LIVING KL-99001 3.5-FT Lighted Kraken with Tentacles

USER MANUAL

Serial Number____
Purchase Date___
AK24008
Thank you for purchasing this HAUNTED LIVING product.
Questions, problems or missing parts?
Before returning, contact us on:
888-251-1006, 8 a.m. – 8 p.m., EST, Monday – Sunday or ascs@lowes.com.

BEFORE ASSEMBLY

  • Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface to avoided damaging parts during assembly.
  • The shipping box can provide an ideal work surface if none is available.
  • Use the components and hardware lists below to inventory and separate each of the components included.
  • To avoid accidentally discarding small components or hardware, do not dispose of any packaging until the assembly is complete.
  • DO NOT USE power tools. Power tools can damage the fasteners and components.

CARE INSTRUCTIONS

  • Use a soft, clean cloth that will not scratch the surface when cleaning.
  • Do not wash or bleach, do not use any cleaners that may damage the paint.
  • Colors and details may vary from the images shown on the packaging.
  • Store in a cool dry place to avoid deformation over time.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not assemble the product – contact customer service first.

Estimated Assembly Time: 20 minutes

Tools Required for Assembly (not included): Phillips Screwdriver

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY
A Tentacle Base 1
B Tentacle End 1
C Tentacle Base 1
D Tentacle End 1
E Kraken Head 1
F Tentacle 1
G Tentacle 1
H Head Base Plate 1
I Tentacle Base Plate 1
J Tentacle Base Plate 1
K Mounting Stake 5
L Power Adapter 1
M Controller 1
N Wiring Harness 1

HARDWARE CONTENTS (shown actual size)

ASSEMBLY INSTRUCTIONS

1. Begin with the largest Tentacle Base [A] and the matching Tentacle End [B].
Connect the male plug from the Tentacle End [B] to the female plug in Tentacle Base [A].
Screw the threaded collar of the male side to the female end to secure the connector.

2. Insert the Tentacle End [B] into Tentacle Base [A] at the assembly collar. Align the geometry of the assembly features so that the Tentacle End [B] can be fully inserted.
Do not pinch the wire between the two parts.
Allow extra wire to fall into Tentacle Base [A] during assembly.

3. Once inserted, rotate Tentacle End [B] clockwise to lock it into place. Once locked, the outer form should align so that the sculpted details match between the two parts, like the image shown in the bottom right corner of the diagram.

4. Repeat step one with Tentacle Base [C] and the matching Tentacle End [D].
Connect the male plug from the Tentacle End [D] to the female plug in Tentacle Base [C].
Screw the threaded collar of the male side to the female end to secure the connector.

5. Repeat Step 2 for Tentacle Base [C] and Tentacle End [D]. Insert the Tentacle End [D] into Tentacle Base [C] at the assembly collar.
Align the geometry of the assembly features so that the Tentacle End [D] can be fully inserted..
Do not pinch the wire between the two parts.
Allow extra wire to fall into Tentacle Base [C] during assembly.

6. Repeat Step 3 with Tentacle Base [C] and Tentacle End [D]. RotateTentacle End [D] clockwise until secure to lock it into place. Once locked, the outer form should align so that the sculpted details match between the two parts, as shown in the image in the bottom right corner of the diagram.

7. Assemble Head Base Plate [H] into the Kraken Head [E] using the included screws [AA]. Flip the head upside down, placing it on a soft surface that will not scratch the paint. Align the holes on the base of the Kraken Head [E] with the threaded holes of the frame, as shown in the diagram. Use a Phillips head screwdriver to assemble the four screws into place, securing Head Base Plate [H] to Kraken Head [E].

8. Place Tentacle Base Plate [I] into the Tentacle Base [A], aligning the screw holes as shown in the diagram. Use a Phillips head screwdriver to assemble the three screws into place, securing Tentacle Base Plate [I] to Tentacle Base [A].

9. Place Tentacle Base Plate [J] into Tentacle Base [C], aligning the screw holes. Use a Phillips head screwdriver to assemble the three screws into place, to secure the bracket.

10. Attach the female ends of the wiring harness [N] to the male wires at the bottom of each Kraken part as shown in the diagram below.
Fasten the threaded collar to secure each connection.
Connect the two-pronged connector from the controle module to power adapter.
You may power the product at this stage to make sure each of the components light up.

11. Ground Staking (OPTIONAL). Recommended
if displaying outdoors in the yard.
Space Mounting Stake [K] 24” – 36” apart. Use a hammer or mallet to drive Mounting Stake [K]  into the ground where Kraken parts will be placed.

Tools Required

12. Place the center holes on the bases of each of the Kraken parts onto the corresponding stakes.

OPERATING INSTRUCTIONS

1. Plug the Power Adapter [L] into a standard power outlet. Use the Controller [M] to turn Kraken on and off.
2. Press the power button to toggle through the three modes.
1. On
2. Timer (on 6 hours, off 18 hours)
3. Off
3. If using the timer function, you must set the product to timer mode at the time you wish to have the product turn on.
4. If the product is unplugged, the timer will be reset and will need to be set again at the desired hour.

WARNING

This item is not a toy and should be used for decoration only. This item contains small parts that can be a choking hazard. Keep all plastic parts and hardware away from children. For indoor and outdoor use.

  • Usage near children should be supervised by adults. Keep away from open flame.
  • Do not climb, push, pull, or tilt the product.
  • Do not modify the product.
  • Assemble and display the product on flat, level surfaces.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna,
  • Increase the separation between the equipment and the receiver,
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or experienced radio/TV technician for help.

CARE AND MAINTENANCE

  • When not in use, store this product in its original packaging.
  • Use a soft, clean cloth that will not scratch the surface when cleaning.
  • Do not wash or bleach, do not use any cleaners that may damage the paint.
  • Colors and details may vary from the images shown on the packaging.
  • Store in a cool dry place to avoid deformation over time.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Assembly Issues Debris or damage to threaded parts Make certain the

components are clear of any debris. Inspect for damaged parts, call customer service
Product is wobbling| The product may be placed on a surface that is rough, uneven, or not level.| Make sure the product is on a hard, flat surface, and all five stakes are in place.
Product is not function- ing.| Adapter is not plugged in to the wall and/or function control box.| Plug the adapter into the wall and function control box when assembly is complete.
Product is not functioning in the way anticipated.| The function control box switch may not be on the desired setting.| Toggle switch to the desired setting.
Part of the product is functioning, but not all of it.| The cable for the non- functioning part of the product may not be connected.| Ensure all cables are connected before operating the product.

WARRANTY

Please remove all parts from the box to check them against this list before attempting to assemble.

If any part is missing or unsatisfactory, call our customer service department at 888-251-1006, 8 a.m. – 8 p.m., EST, Monday – Sunday. You may also contact us at ascs@lowes.com.

Specifications

  • Item #: 5745254

  • Model #: KL-99001

  • Product Name: 3.5-FT Lighted Kraken with Tentacles

FAQ

Q: What should I do if the product is not functioning properly?

A: Check if all cables are connected properly and toggle the function control box switch to the desired setting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals